Gotham Lighting EVO® 6" Round Pendant Mount Cylinder Installation guide

Brand: Gotham Lighting

Model: EVO® 6" Round Pendant Mount Cylinder

Type: Installation guide

IMPORTANT SAFETY INSTRUCTIONS

OCCUPIED SPACES DIRECT IRRADIATION UV EQUIPMENT

READ AND FOLLOW ALL SAFETY INSTRUCTIONS!

IMPORTANT SAFEGUARDS

When using electrical equipment, basic safety precautions should always be followed including the following:

•To reduce the risk of death, personal injury or property damage from fire, electric shock, falling parts, cuts/abrasions, and other

hazards please read all warnings and instructions included with and on the fixture box and all fixture labels.

•Before installing, servicing, or performing routine maintenance upon this equipment, follow these general precautions.

•Installation and service of this equipment should be performed by a qualified licensed electrician.

•Equipment should be mounted in locations and at heights where it will not readily be subjected to tampering by unauthorized

personnel.

•The use of accessory equipment not recommended by the manufacturer may cause an unsafe condition.

•Do not use this equipment for other than intended use.

•It is the obligation of the end-user to consult with appropriately qualified Professional Engineer(s), Certified Infection Control

professionals, and Certified Industrial Hygienists, as applicable, to determine whether this equipment and its installation meets

the applicable requirements for system performance, code compliance, safety, suitability and effectiveness for use in a

particular application design.

•DO NOT INSTALL DAMAGED PRODUCT! This equipment has been properly packed so that no parts should have been damaged

during transit. Inspect to confirm. Any equipment damaged or broken during or after installation should be replaced. Contact

the manufacturer for replacement.

•DO NOT INSTALL BELOW THE MINIMUM HEIGHT SPECIFIED IN THESE INSTALLATION INSTRUCTIONS.

•Follow all disposal laws when replacing or disposing. Excimer lamps do not contain hazardous materials and can be recycled by

standard electronics recyclers.

•These instructions do not purport to cover all details or variations in equipment nor to provide every possible contingency to

meet in connection with installation, operation, or maintenance. Should further information be desired, or should problems

arise which are not covered sufficiently for the purchaser’s or owner’s purposes, please contact Technical Services at Acuity

Brands Lighting, 800-705-SERV (7378).

*Asterisked statements only apply to UV222 and UV222H configurations, not applicable to UV222VL configurations. UV222VL

configurations do not have a UVC emitter, no UVC precautions necessary with UV222VL configurations.

•This equipment is designed for use with germicidal UV radiation sources and must be installed in compliance with competent

technical directions to prevent risk of personal injury from UV radiation.*

•UV radiation can pose a risk of personal injury. Overexposure can result in damage to eyes and bare skin. To reduce the risk of

overexposure this equipment must be installed in accordance with the manufacturer’s site planning recommendations. This may

include instructions on the relative location of each germicidal system component, the minimum distances between UV-

generating devices and other objects or surfaces, and protection from line-of-sight exposure to UV radiation in occupied spaces

located above the equipment mounting area (e. g. upper floor balconies, open staircases, etc.).*

•UV and optical radiation can be reflected by surrounding surfaces such as ceilings and walls. Since the reflective properties of

surfaces can vary widely, it should be considered as part of site planning. Follow the manufacturer’s recommendations for

selecting appropriate ceiling and wall finishes.*

•IT IS THE RESPONSIBILITY OF THE INSTALLER TO ENSURE THAT PERSONS WILL NOT BE EXPOSED TO EXCESSIVE UV OR OPTICAL

RADIATION DURING EQUIPMENT OPERATION. THIS WILL REQUIRE THE INSTALLER TO CONDUCT AN ASSESSMENT OF

IRRADIANCE OR ILLUMINANCE LEVELS IN THE SURROUNDING OCCUPIED SPACES PRIOR TO OCCUPANCY.*

•Maintenance and servicing of this UV generating equipment shall be performed by authorized personnel. Service personnel

must wear appropriate Personal Protective Equipment (PPE) if the equipment will be in operation during the maintenance or

servicing work. Contact the equipment manufacturer for PPE recommendations and guidance.*

•Take precautions to ensure that the concentration of ozone in the installation is limited to a value that is within applicable

permissible exposure limits. Verify acceptable ozone concentrations in the installation taking into account the number of

products in a given volume of space, the characteristics of the ventilation system, access, and other factors. Permissible

exposure limits vary based on the place of ozone application, the length of exposure, and other factors and are publicly

available. For reference, the EPA National Ambient Air Quality Standard is 0.070 ppm maximum concentration averaged over 8

hours and current OSHA regulations set an eight-hour time-weighted average permissible exposure limit of 0.10 ppm. The

amount of ozone emitted by this equipment does not exceed a concentration of 0.001 ppm over an 8-hour period, as tested in

accordance with UL 867.*

•UVC module not intended for use with wall switches. Connect to an unswitched circuit intended for 24/7/365 continuous

operation.*

•To ensure that the equipment may continue to operate as designed, replacements for the proprietary UV Module System (UV

Lamp Module and Dosage Controller) must be purchased from Acuity Brands Lighting. Contact Acuity Brands Lighting when the

UV Lamp Module reaches end of life.*

•This equipment, including the lamp modules, must be stored in a dust-free environment and be handled while wearing clean

gloves. Since far-UVC radiation is absorbed by proteins and other organic compounds, accumulation of dust particles or touching

of the optical radiation surface will negatively impact the output of the UV radiation source. Follow recommended cleaning

procedures when dirt is observed on the lens and as part of a regular maintenance cleaning cycle.*

SAVE THESE INSTRUCTIONS AND DELIVER TO OWNER AFTER INSTALLATION

Gotham | Acuity Brands Lighting, Inc., One Lithonia Way, Conyers, GA 30012 • 800-705-SERV (7378) • www.gothamlighting.com

Gotham, nLight, and the Acuity Brands logos are registered trademarks of Acuity Brands. Care222 is a registered trademark of Ushio America, Inc.

Products herein may be covered by one or more U.S. Patents and Patents Pending. Specifications subject to change without notice.

912-00308-001 Rev. B

Page 1 of 17

Disconnect or turn off power before installation or

servicing.

Verify that supply voltage is correct by comparing it with

the equipment label information.

Make all electrical and grounded connections in

accordance with the National Electrical Code (NEC) and any

applicable local code requirements.

All wiring connections should be capped with UL approved

recognized wire connectors.

WARNING

RISK OF ELECTRIC SHOCK

Allow lamp/fixture to cool before handling. Do not touch

hot lens, lamp, guard, or enclosure.

Follow all lamp manufacturer’s warnings,

recommendations and restrictions on lamp operation

including but not limited to: ballast type, burning

position, replacement, and recycling.

WARNING

RISK OF BURN

Wear gloves and safety glasses at all times when removing

equipment from carton, installing, servicing or performing

maintenance.

Avoid direct eye exposure to the light source while it is on.

CAUTION

RISK OF INJURY

Keep combustible and other materials that can burn away

from lamp/lens.

Do not operate in close proximity to persons,

combustible materials or substances affected by heat or

drying.

CAUTION

RISK OF FIRE

Disconnect or turn off power to equipment before

performing maintenance or servicing other elements in the

ceiling or space that require closer proximity than normal

standing height away from the equipment.

Skin or eye injury may result from overexposure to the light

produced by the lamp in this equipment at distances less

than 24 in. from the emitter.

Emitters used within this equipment are in the EXEMPT

RISK GROUP for actinic UV (200-400nm), near UV

(315-400nm), and blue light (300-700nm) hazards, as

described in IEC 62471, when installed and used according

to instructions in this document.

UV emitters used in this equipment can cause the limited

photodegradation of many materials over years of

operation. For the few materials where photodegradation

may be more significant (such as PVC), remove or protect

these materials prior to operation of the unit if degradation

is a concern. Tested materials are identified in the

Photodegradation Testing Results summarized on the

specification sheet for this equipment.

CAUTION

UV EXPOSURE RISKS

UV222 & UV222H ONLY*

IMPORTANT SAFETY INSTRUCTIONS

OCCUPIED SPACES DIRECT IRRADIATION UV EQUIPMENT

PRECAUTIONARY STATEMENTS

HAZARDS TO HUMANS AND DOMESTIC ANIMALS

This equipment emits UV radiation at wavelengths less

than 250 nm which can generate ozone.

Take precautions to ensure that ozone concentration

stays within applicable permissible exposure limits

described on page 1 of this document.

CAUTION

OZONE EXPOSURE RISK

UV222 & UV222H ONLY*

*Asterisked warnings only apply to UV222 and UV222H configurations, not applicable to UV222VL configurations.

UV222VL configurations do not have a UVC emitter, no UVC precautions necessary with UV222VL configurations.

SAVE THESE INSTRUCTIONS AND DELIVER TO OWNER AFTER INSTALLATION

912-00308-001 Rev. B

Page 2 of 17

Gotham | Acuity Brands Lighting, Inc., One Lithonia Way, Conyers, GA 30012 • 800-705-SERV (7378) • www.gothamlighting.com

Gotham, nLight, and the Acuity Brands logos are registered trademarks of Acuity Brands. Care222 is a registered trademark of Ushio America, Inc.

Products herein may be covered by one or more U.S. Patents and Patents Pending. Specifications subject to change without notice.

IMPORTANT SAFETY INSTRUCTIONS

OCCUPIED SPACES DIRECT IRRADIATION UV EQUIPMENT

READ AND FOLLOW ALL SAFETY INSTRUCTIONS!

Never connect components under load.

Do not mount or support these fixtures in a manner that can cut the outer jacket or damage wire insulation.

Controls for dimming, auto-sensing, or remote control of a luminaire that are not factory-wired to the luminaire

must be checked for compatibility with the luminaire prior to installation. LED components must be powered

directly from a switched circuit while UVC components must be powered directly from an unswitched circuit.

Unless individual product specifications deem otherwise, do not restrict fixture ventilation. Allow for some

volume of airspace around fixture. Avoid covering LED fixtures with insulation, foam, or other material that will

prevent convection or conduction cooling.

Unless individual product specifications deem otherwise, do not exceed fixture’s maximum ambient temperature.

Only use fixture in its intended location.

LED products are polarity sensitive. Ensure proper polarity before installation.

Electrostatic Discharge (ESD): ESD can damage LED fixtures. Personal grounding equipment must be worn during all

installation or servicing of the unit.

Do not touch individual electrical components as this can cause ESD, shorten lamp life, or alter performance.

Some components inside the fixture may not be serviceable. In the unlikely event your unit may require service,

stop using the unit immediately and contact an Acuity Brands Lighting representative for assistance.

Always read the fixture’s complete installation instructions prior to installation for any additional fixture specific

warnings.

Always ensure that the electrical distribution system is up to NEC (and any applicable local code) requirements.

Verify that power distribution system has proper grounding. Lack of proper earth ground can lead to fixture failure

and may void warranty.

CAUTION: RISK OF PRODUCT DAMAGE

All luminaires that contain electronic devices that generate frequencies above 9kHz from any component within the luminaire comply with Part

15 of the FCC Rules. Operation is subject to the following two conditions:

(1) This device may not cause harmful interference

(2) This device must accept any interference received, including interference that may cause undesired operation

This device complies with Part 18 of the FCC Rules but may cause interference with cordless and cell phones, radios, televisions, and other

electronic devices. To correct the problem, move the device away from the luminaire or plug into a different outlet. This product may cause

interference to radio equipment and should not be installed near maritime safety communications equipment or other critical navigation or

communications equipment operating between 0.45-30MHz.

Failure to follow any of these instructions could void product warranties available at www.acuitybrands.com/support/warranty. For

technical assistance, call 800-705-SERV (7378).

EPA Establishment Number: 97727-IN-1. For sale only in the United States of America and Mexico. Not registered as a pesticide device and not intended for sale into the

following U.S. states: Colorado, Hawaii, Indiana, New Mexico, Oklahoma, West Virginia, Wyoming, and the District of Columbia.

Does not meet California air cleaner regulation requirements; cannot be shipped to California.

Acuity Brands Lighting, Inc. assumes no responsibility for claims arising out of improper or careless installation or handling of its products.

SAVE THESE INSTRUCTIONS AND DELIVER TO OWNER AFTER INSTALLATION

912-00308-001 Rev. B

Page 3 of 17

Gotham | Acuity Brands Lighting, Inc., One Lithonia Way, Conyers, GA 30012 • 800-705-SERV (7378) • www.gothamlighting.com

Gotham, nLight, and the Acuity Brands logos are registered trademarks of Acuity Brands. Care222 is a registered trademark of Ushio America, Inc.

Products herein may be covered by one or more U.S. Patents and Patents Pending. Specifications subject to change without notice.

UVC Module

Violet hue visible

during on cycle

THIS PAGE ONLY APPLIES TO UV222 & UV222H CONFIGURATIONS

Cylinder Aperture

•When line voltage is applied to the luminaire, the Status Indicator LED should appear as a green solid light. The UV lamp

module will remain inactive for between 11 and 12 minutes. Complete any mechanical adjustments to the luminaire

before applying line voltage, or else ensure that any work on or near the luminaire that would require any part of the

installer to be more than 7 ft. off the floor is complete within the first 11 minutes after line voltage is applied to prevent

the installer from receiving a UV dose that is larger than the recommended amount.

•The UV lamp module will operate on 12-minute cycles, activating for a duration between 10 and 50 seconds each cycle.

The duration will depend on the Programming Option value in each luminaire’s order nomenclature (e.g. EVO6…D108).

Refer to the product Spec Sheet for guidance in selecting the correct Programming Option value for each application.

•When activated, the UV module will illuminate with a soft violet glow (see image below). The Status Indicator LED will

remain green whether the UV module is active or inactive if all self-diagnostics report proper function.

•The Status Indicator LED may reflect additional states throughout the lifetime of the luminaire. The possible states are as

follows:

•The UV lamp modules are rated for approximately 5 years of life (3000 activated hours). The Status Indicator LED will

change to yellow solid when six months of projected life are left in the lamp module. Contact Acuity Brands Lighting

for service.

•The UV Module only version is an ultraviolet (UV) based device that is not serviceable. The Hybrid (H) version contains an

embedded UV based device that is not separable from the fixture and is also not serviceable. Therefore, if this fixture

experiences a failure due to a defect in material or workmanship after the warranty period has expired or the fixture

reaches the end of its useful life then, if continued operation is desired, a new fixture must be purchased.

912-00308-001 Rev. B

Page 4 of 17

Gotham | Acuity Brands Lighting, Inc., One Lithonia Way, Conyers, GA 30012 • 800-705-SERV (7378) • www.gothamlighting.com

Gotham, nLight, and the Acuity Brands logos are registered trademarks of Acuity Brands. Care222 is a registered trademark of Ushio America, Inc.

Products herein may be covered by one or more U.S. Patents and Patents Pending. Specifications subject to change without notice.

EVO6 CARE222® Cylinders

DESCRIPTION OF NORMAL OPERATION UV222H: Visible light integrated with 222nm UV module

UV222: 222nm UV module only

UV222VL: Visible light only (no UV module)

UV Emitter Information

•HIGHEST IRRADIANCE AT 500 mm: 0.51 W/m2

•Dosing is listed as height from floor to the mounting surface of the luminaire.

•Minimum floor to mounting surface height:

*All measurements in μW/cm2measured at plane 7 ft. above floor -1x1 ft. grid

**All measurements in mJ/cm2per 8 hours, measured at plane 7 ft. above floor -1x1 ft. grid. ACGIH guideline for maximum dose is 22.87 mJ/cm2

per 8 hours. Consult an Acuity Brands UV Lighting Specialist for layout of multiple-luminaire installations.

EVO6…D108 = 105 Inch (min) to 111 Inch (max) height from floor to cylinder aperture

EVO6…D114 = 111 Inch (min) to 117 Inch (max) height from floor to cylinder aperture

EVO6…D120 = 117 Inch (min) to 123 Inch (max) height from floor to cylinder aperture

EVO6…D126 = 123 Inch (min) to 129 Inch (max) height from floor to cylinder aperture

EVO6…D132 = 129 Inch (min) or greater height from floor to cylinder aperture

912-00308-001 Rev. B

Page 5 of 17

Gotham | Acuity Brands Lighting, Inc., One Lithonia Way, Conyers, GA 30012 • 800-705-SERV (7378) • www.gothamlighting.com

Gotham, nLight, and the Acuity Brands logos are registered trademarks of Acuity Brands. Care222 is a registered trademark of Ushio America, Inc.

Products herein may be covered by one or more U.S. Patents and Patents Pending. Specifications subject to change without notice.

EVO6 CARE222® Cylinders

DESCRIPTION OF NORMAL OPERATION UV222H: Visible light integrated with 222nm UV module

UV222: 222nm UV module only

UV222VL: Visible light only (no UV module)

These installation instructions are used for installing the following luminaires and kits.

Luminaire Variants Mounting Type Mounting Type Description

EVO6PC UV222H (Visible Light and UV Module)

EVO6PC UV222 (UV Module Only)

EVO6PC UV222VL (Visible Light Only)

JBX Integral driver, Recessed or Surface J-

box

JBXCC Integral driver, Surface J-box with

Conduit Covers

EVO6 CARE222® Cylinders

INSTALLATION INSTRUCTIONS

A) Identification of Pendant Stem Luminaires…............................... ………….……………………… Page 6

B) Identification of Parts…................................................................ ………….……………………… Page 7

C) Stem Length Calculation………………………………………….... ………….……………………… Page 8

D) Care222 Information Label Removal and Placement………...…. …………………………………. Page 9

E) Stem End Hole Drilling for Swivel Ball…...................................... ………….……………………… Page 9

F)Stem Cylinder Assembly…........................................................... ………….……………………… Page 10

G) Conduit Canopy Assembly (JBXCC)…......................................... ………….……………………… Page 11

H) Fixture Install…………………..….................................................. ………….……………………… Page 12

I) Cleaning Instructions………………………………………………... ………….……………………… Page 17

JBX

(Recessed

J-box)

JBX

(Sloped Ceiling

Canopy)

JBX

(Surface

J-box)

JBXCC

(Ceiling

Canopy)

JBXCC

(Slope Ceiling

Canopy)

A) Identification of Pendant Mount Luminaires

UV222H: Visible light integrated with 222nm UV module

UV222: 222nm UV module only

UV222VL: Visible light only (no UV module)

912-00308-001 Rev. B

Page 6 of 17

Gotham | Acuity Brands Lighting, Inc., One Lithonia Way, Conyers, GA 30012 • 800-705-SERV (7378) • www.gothamlighting.com

Gotham, nLight, and the Acuity Brands logos are registered trademarks of Acuity Brands. Care222 is a registered trademark of Ushio America, Inc.

Products herein may be covered by one or more U.S. Patents and Patents Pending. Specifications subject to change without notice.

B) Identification of Parts

Stem Cylinder

Assembly

Stem

a) External and internal threaded ends

iEVO6PC external threads: 3/8-18 NPSM

b) Internal threaded ends

i. EVO6PC internal threads: 1/4-18 NPSM

c) Threaded nipple

Stem Hardware

a) Swivel ball

b) Screw (2)

a) #8-32 x 3/8”

Lg. Pan

Head

a) b)

Canopy Assembly

a) JBX Canopy

b) JBXCC Canopy

Conduit Keys (JBXCC Only)

a) Blank Conduit Key (4)

b) Conduit Key (4)

c) 5/64” Allen wrench (1)

a) c) b)

912-00308-001 Rev. B

Page 7 of 17

Gotham | Acuity Brands Lighting, Inc., One Lithonia Way, Conyers, GA 30012 • 800-705-SERV (7378) • www.gothamlighting.com

Gotham, nLight, and the Acuity Brands logos are registered trademarks of Acuity Brands. Care222 is a registered trademark of Ushio America, Inc.

Products herein may be covered by one or more U.S. Patents and Patents Pending. Specifications subject to change without notice.

Calculate the necessary stem length per the equations below.

C) Stem Length Calculation

Cut line

Stem Length (2” MINIMUM)

Cut off

WARNING: DO NOT CUT OFF

EXTERNAL THREAD SIDE OF PIPE

If there are multiple sections of stem, assemble them together using the threaded nipples provided.

Cut the assembled stem to the calculated length per Step 1.

Stem Length = B –A –11”

Desired

illuminated

surface

Mounting Plane

(J-Box)

Bottom of

cylinder

Mounting Height (in)

Surface J-Box Sloped Surface

(45deg)

Measure B from

center of J-Box

for length

calculation with

sloped surfaces.

Recessed J-box

Fixture Height (in)

912-00308-001 Rev. B

Page 8 of 17

Gotham | Acuity Brands Lighting, Inc., One Lithonia Way, Conyers, GA 30012 • 800-705-SERV (7378) • www.gothamlighting.com

Gotham, nLight, and the Acuity Brands logos are registered trademarks of Acuity Brands. Care222 is a registered trademark of Ushio America, Inc.

Products herein may be covered by one or more U.S. Patents and Patents Pending. Specifications subject to change without notice.

E) Stem End Hole Drilling for Swivel Ball

123

Locate the swivel ball and stem that

has already been assembled and cut

to length.

Place swivel ball on the stem

end opposite of the external

threads.

4 5

Make sure ball is seated on the

top of the stem. Thread screws

into each side of the swivel ball to

secure it in place before drilling.

Using the guide holes in the ball and

a drill with a 3/16” drill bit, drill

through both sides of the stem.

Loosen screws and remove swivel ball

from stem for later assembly steps.

Note: Swivel Ball will be secured to the

stem in a later step by tightening screws

and engaging them into the holes that

were drilled in the end of the stem.

3/16”

drill bit

912-00308-001 Rev. B

Page 9 of 17

D) Care222® Information Label Removal and Placement

1Remove the Care222 Information Label (the lower

rectangular portion of the hanging label).

2Remove sticker backing and affix label in a location

that will be visible after installation and likely to be

discovered by future maintenance personnel.

Suggested locations include: a cover plate near the

entrance to the room containing the Care222 fixture,

the electrical panel supplying the luminaire branch

circuit, or a clean, smooth wall near the room

entrance.

Gotham | Acuity Brands Lighting, Inc., One Lithonia Way, Conyers, GA 30012 • 800-705-SERV (7378) • www.gothamlighting.com

Gotham, nLight, and the Acuity Brands logos are registered trademarks of Acuity Brands. Care222 is a registered trademark of Ushio America, Inc.

Products herein may be covered by one or more U.S. Patents and Patents Pending. Specifications subject to change without notice.

F) Stem Cylinder Assembly

1Unscrew cap from cylinder. Align stem with the cylinder so

the external threads of the stem are closest to the top of

the cylinder. Pull the wires through the stem, then thread it

into the cylinder. Leave at least 6” of wires coming out of

the end of the stem.

Note: Set screw may need to be loosened to allow

threading in the stem.

2Once the stem has been threaded in fully, tighten the

set screw to lock the stem in the cylinder. Then screw

on and hand tighten the cap.

Set Screw

Cap

6” MIN

Cap

912-00308-001 Rev. B

Page 10 of 17

Gotham | Acuity Brands Lighting, Inc., One Lithonia Way, Conyers, GA 30012 • 800-705-SERV (7378) • www.gothamlighting.com

Gotham, nLight, and the Acuity Brands logos are registered trademarks of Acuity Brands. Care222 is a registered trademark of Ushio America, Inc.

Products herein may be covered by one or more U.S. Patents and Patents Pending. Specifications subject to change without notice.

G) Conduit Canopy Assembly (JBXCC)

2 3

If JBX fixture, skip to Section H. Select the appropriate keys and insert them into the correct canopy slots for each

specific J-box configuration. Adjust set screws in the keys to allow the keys to slide in completely.

Note: Keys accept ½” and ¾” EMT conduit ONLY. Conduit fittings may vary by manufacturer. If using ¾” set

screw type fittings, the fitting may need to be rotated so that the set screw is off vertical for proper clearance

with canopies.

Loosen screws securing the plate to the

canopy so the screws can slide within the

slots.

Bring canopy up to J-box and insert J-box screws into key slots.

Rotate the plate attached to the canopy to allow the J-box

screws to slide into the key slots. Tighten the screws that secure

the plate to the canopy. This will secure the canopy to the ceiling

for fixture install. Leave J-box screws loose for fixture install.

Screw

Screws Screws

Plate

Rotate ¾” set

screw fittings

off vertical

NOTE: JBXCC mounting type requires a 1.5” depth, 4” octagonal junction box.

912-00308-001 Rev. B

Page 11 of 17

Gotham | Acuity Brands Lighting, Inc., One Lithonia Way, Conyers, GA 30012 • 800-705-SERV (7378) • www.gothamlighting.com

Gotham, nLight, and the Acuity Brands logos are registered trademarks of Acuity Brands. Care222 is a registered trademark of Ushio America, Inc.

Products herein may be covered by one or more U.S. Patents and Patents Pending. Specifications subject to change without notice.

1Slide Canopy (1), Mounting Bracket (2), and

Swivel Ball (3) onto stem in below order.

Note: Rest the Canopy and Mounting Bracket

on the top of the cylinder.

H) Fixture Install

Thread screws into swivel ball and align with drilled

holes in stem. Tighten screws so they are engaged

through the holes in the stem.

Drilled Hole (x2)

NOTE:

JBX mounting type fixtures require a 1.5” minimum depth, 4” octagonal junction box.

JBXCC mounting type fixtures require a 1.5” depth, 4” octagonal junction box.

Recessed junction boxes cannot be more than 1/8” proud of the ceiling surface.

WARNING: All pendant fixtures exposed to wind require tethering –consult factory.

3Align swivel ball groove with mounting plate tab as

it is brought up to secure to ceiling.

912-00308-001 Rev. B

Page 12 of 17

Gotham | Acuity Brands Lighting, Inc., One Lithonia Way, Conyers, GA 30012 • 800-705-SERV (7378) • www.gothamlighting.com

Gotham, nLight, and the Acuity Brands logos are registered trademarks of Acuity Brands. Care222 is a registered trademark of Ushio America, Inc.

Products herein may be covered by one or more U.S. Patents and Patents Pending. Specifications subject to change without notice.

H) Fixture Install –Continued…

4Bring the fixture up to junction box with the swivel

ball seated in the mounting plate. 5Pull stem wires through the multiple triangular cutouts in

the mounting plate. Also pull the corresponding supply

wires through each respective cutout.

Triangular

Cutout

Do not pull

wires through

square cutouts.

JBX

Supply Wires, Visible Light

(SWITCHED CIRCUIT)

JBXCC

Supply Wires, UV Module

(UNSWITCHED CIRCUIT)

912-00308-001 Rev. B

Page 13 of 17

Gotham | Acuity Brands Lighting, Inc., One Lithonia Way, Conyers, GA 30012 • 800-705-SERV (7378) • www.gothamlighting.com

Gotham, nLight, and the Acuity Brands logos are registered trademarks of Acuity Brands. Care222 is a registered trademark of Ushio America, Inc.

Products herein may be covered by one or more U.S. Patents and Patents Pending. Specifications subject to change without notice.

Use the keyholes in the mounting bracket to

secure it with the J-box screws. Align screws

with the indication marks on the bracket.

Adjust as necessary for fixture alignment.

Tighten screws.

After securing mounting plate, make wire connections per below diagram and

push them through the mounting bracket cutouts into the J-box.

H) Fixture Install –Continued…

EVO6PC UV222H (Visible Light and UV Module)

GREEN WIRE FROM

STEM

GRAY (or PINK)

PURPLE

WHITE

BLACK

DIM (-)

DIM (+)

NEUTRAL

HOT

GROUND

J-BOX

CONNECTIONS

NEUTRAL

HOT

GROUND

WIRES LABELED

SWITCHED

WIRES LABELED

UNSWITCHED

BLACK

WHITE

SUPPLY

WIRES

VISIBLE

LIGHT

CIRCUIT

BRANCH

SUPPLY WIRES

UN-SWITCHED UV

CIRCUIT BRANCH

CYLINDER

COPPER WIRE (FROM

MOUNTING PAN)

CYLINDER

912-00308-001 Rev. B

Page 14 of 17

Gotham | Acuity Brands Lighting, Inc., One Lithonia Way, Conyers, GA 30012 • 800-705-SERV (7378) • www.gothamlighting.com

Gotham, nLight, and the Acuity Brands logos are registered trademarks of Acuity Brands. Care222 is a registered trademark of Ushio America, Inc.

Products herein may be covered by one or more U.S. Patents and Patents Pending. Specifications subject to change without notice.

H) Fixture Install –Continued…

GREEN WIRE

FROM STEM

CYLINDER

WHITE

BLACK

NEUTRAL

HOT

J-BOX

CONNECTIONS

CYLINDER

COPPER WIRE

(FROM MOUNTING PAN)

GROUND

SUPPLY WIRES

UN-SWITCHED UV

CIRCUIT BRANCH

EVO6PC UV222 (UV Module Only)

EVO6PC UV222VL (Visible Light Only)

COPPER WIRE (FROM

MOUNTING PAN)

CYLINDER

GRAY (or PINK)

PURPLE

WHITE

BLACK

GREEN WIRE

(FROM STEM)

DIM (-)

DIM (+)

NEUTRAL

HOT

GROUND

J-BOX

CONNECTIONS

SUPPLY

WIRES

VISIBLE

LIGHT

CIRCUIT

BRANCH

WIRES LABELED

UNSWITCHED

912-00308-001 Rev. B

Page 15 of 17

Gotham | Acuity Brands Lighting, Inc., One Lithonia Way, Conyers, GA 30012 • 800-705-SERV (7378) • www.gothamlighting.com

Gotham, nLight, and the Acuity Brands logos are registered trademarks of Acuity Brands. Care222 is a registered trademark of Ushio America, Inc.

Products herein may be covered by one or more U.S. Patents and Patents Pending. Specifications subject to change without notice.

9Bring the canopy up to the ceiling and align the spring clips on the canopy with the rectangular cutouts on

the bracket. Push the canopy up to the ceiling to snap the clips into the cutouts to secure the canopy.

H) Fixture Install –Continued…

Spring Clips Rectangular

Cutouts

JBX

912-00308-001 Rev. B

Page 16 of 17

Gotham | Acuity Brands Lighting, Inc., One Lithonia Way, Conyers, GA 30012 • 800-705-SERV (7378) • www.gothamlighting.com

Gotham, nLight, and the Acuity Brands logos are registered trademarks of Acuity Brands. Care222 is a registered trademark of Ushio America, Inc.

Products herein may be covered by one or more U.S. Patents and Patents Pending. Specifications subject to change without notice.

1Disconnect power to the unit prior to opening or performing any maintenance.

I) Cleaning Instructions

2Wipe off exterior dirt and debris using a soft, clean cloth. A mild detergent and water may be used if

necessary. CAUTION: DO NOT USE ABRASIVE CLEANERS ON THE LENS. THEIR USE MAY RESULT

IN DAMAGE.

If dust or fingerprints are present on the lens, clean the glass with a non-abrasive cleaner, such as a glass

cleaner or disinfecting wipes. It is recommended that the glass be cleaned periodically to retain intended

UV-C transmission.

912-00308-001 Rev. B

Page 17 of 17

Gotham | Acuity Brands Lighting, Inc., One Lithonia Way, Conyers, GA 30012 • 800-705-SERV (7378) • www.gothamlighting.com

Gotham, nLight, and the Acuity Brands logos are registered trademarks of Acuity Brands. Care222 is a registered trademark of Ushio America, Inc.

Products herein may be covered by one or more U.S. Patents and Patents Pending. Specifications subject to change without notice.

Gotham Lighting EVO® 6" Round Pendant Mount Cylinder Installation guide

Gotham Lighting EVO® 6" Round Pendant Mount Cylinder Installation guide

Gotham Lighting EVO® 6" Round Pendant Mount Cylinder Installation guide

Other documents