Fox Hybrid and AC Charger H3 and AC3 Installation guide

Brand: Fox

Model: Hybrid and AC Charger H3 and AC3

Type: Installation guide

Fox Hybrid and AC Charger H3 and AC3 are versatile devices that offer a range of features for optimizing energy usage and ensuring a reliable power supply. With the ability to seamlessly integrate solar power, store excess energy in batteries, and provide backup power during grid outages, these devices are ideal for residential and commercial applications seeking energy independence and resilience. Their advanced monitoring and control capabilities allow for efficient energy management and remote access, making them a smart choice for modern energy needs.

QUICK INSTALLATION GUIDE

Step1: Fix the bracket on the wall

Step2: Match the inverter with wall bracket

Choose the place you want to install the inverter.



bracket.

Please make sure the inverter will be installed with a proper distance

as shown below.

Pon Min Distance

 500mm

Right 500mm

Top



500mm

2. Installaon Steps

Drill holes with electric drill, make sure the holes are at least 50mm deep







Mount the inverter to the bracket. Secure the inverter with the M5

screw and washer.

Please reer to the ollowing steps to start up the inverter.

1. Ensure the inverter ed well.

2. Make sure all wirings are completed.

3. Make sure the meter is connected well.

4. Make sure the baery is connected well.

5. Make sure the eternal EPS contactor is connected well d).



.

Turn on the PV/DC switch (or Hybrid version only), AC breaker, EPS

breaker and baery breaker.



quickly go to the START/STOP page and set it to start.



Note:

· When starg inverter or the rst e, the country code will be

set by deault to the local segs. Check i the country code is correct.

· Set the the inverter using the buon or by using the APP.

Please reer to the ollowing steps to switch othe inverter.

1. Enter the segs page, select START / STOP and set it to stop.

2. Turn o the PV/DC switch (or Hybrid version only), AC breaker, EPS

breaker and baery breaker.

3. Wait 5 min beore you open the upper lin repair).





5. Inverter Start-Up

6. Inverter Switch O

• Push the threaded sleeve into the socket, ghten up

the cap on the terminal.

B. GRID Wiring

• Separate the ON-GRID plug into three parts as below.

1. Hold the middle part the emale insert, rotate the back shell to

loosen it, and detach itrom emale inset.

2. Remove the cable nut (with rubber insert) rom the back shell.

• Slide the cable nut and then the back shell onto the cable.

PV Wiring (For Hybrid version Only)

 Wiring

· Choose 12 AWG wire to connect the PV module.

·

12AWG

8AWG

10AWG

· Trim minsularom the wire end.

· Choose 8 AWG wire to connect t

·

· Trim minsularom the wire end.

· Separate the DC connector (PV) as below.

· Insert striped cable into pin contact and ensure all conductor strands

are captured in the pin contact.

· Insert pin contact through the cable nut to assemble into back o the

male or emale plug. When you eel or hear a click the pin contact

assembly is seated correctly.

4. Wiring Steps

· Crimp pin contact by using a crimping plier. Put the pin

contact with striped cable into the corresponding

crimping pliers and crimp the contact.

Plug Pin contact cable nut

D-

D+

· Separate the DC connector () as below.

· Insert striped cable into pin contact and ensure all conductor strands

are captured in the pin contact.

· Insert striped cable into earth terminal and ensure all conductor strands

are captured in the earth terminal.

Plug Pin contact cable nut

D-

D+

· Insert pin contact through the cable nut to assemble into back o the

male or emale plug. When you eel or hear a click the pin contact

assembly is seated correctly.

· Crimp pin contact by using a crimping plier. Put the

pin contact with striped cable into the corresponding

crimping pliers and crimp the contact.

Quick Installaon Guide 5-12kW Three Phase Storage Inverter

Object Quanty Descripn Object Quanty Descripn

A 1 Inverter

B 2 Brackets

CPV connectors (Only  H3)

(3*posie, 3*negae)

1LAN/GPRS (Oponal)

DPV pin contacts (Only or H3)

(3*posie, 3*negae)

Meter









2 AC connectors al screws

Eansion tubes &

G 1 Earth terminal

H 1 Communicaon connector

I 1 Product manual

A B C D

 G H

I J K L

1. Packing List

Quick

Guide

Installaon

Manual

sion screws

Meter and RS485 should be connected to inverter by the connector



to the corresponding ports on inverter

Port

1 2 3 4 5 6 7 8

Meter/

485

485A / / RY_ CON +12V

485B

Meter

485B Meter

485A

Note:





Note:

1. CompaMeter type: DTSU (CHINT).

2. 

;

3. Serial Port Conneons

V1.3

10-203-00172-03

•



Locker

female

Housing hole

male

Housing hole

• Put the sealing body and yarn trapper into the main body, screw the

lock nut into the main body, and the torque is (2.5 + / - 0.5N·m).

• Insert the male end into the emale end. or the rota direc o

the lock, please reer to the LOCK mark on the assembly.

•

Click

Push Housing into Body.

· Unlock the DC connector:

- Use the specied wrench tool.

- When separag the DC+ connector, push the tool downrom the

top.

- When separag the DC- connector, push the tool dowrom the

bom.

- Separate the connectors by hand.

· Unlock the DC connector:

- Use the specied wrench tool.

- When separag the DC+ connector, push the tool downrom the

top.

- When separag the DC- connector, push the tool dowrom the

bom.

- Separate the connectors by hand.

Grounding Wiring

Use the crimping pliers to press the ground cable into the ground terminal,

screw the ground screw with screwdriver as shown below.

• Push the threaded sleeve to connerminal unl both

are locked ghtly on the inverter.

• Remove the GRID connector: Press the bayonet out othe slot

with a small screwdriver or the unlock tool and pull it out,

or unscrew the threaded sleeve, then pull it out.

• Remove the EPS connectorPress the bayonet with a small screwdriver

or the unlock tool.

the assembly, then pull it out.

Note: Please reer to local cable type and color or actual installa

A. EPS Wiring

•

L1/L2/L3: Brown/Red/Green or Yellow Wire

N: Blue/Black Wire

PE: Yellow & Green Wire

Nutclaw

Seal body Nut

Seal body

short body long body

Set the parts on the cable.

- Trim all the wires to 52.5mm and the PE wire to 55mm.

- Use the crimping pliers to trim 12mm insula all wire ends as

shown in the picture.

Grid Wiring

Cable dimensions

Click

Quick installae1



Note:





500mm

500mm500mm

Trim minsularom the wire end.

· Crimp earth terminal by using a crimping plier. Put the

earth terminal with striped cable into the corresponding

crimping pliers and crimp the contact.

EPS

GRID

Modell (kW)

Cable (ON-GRID) mm² mm² mm² mm²

Cable (EPS) mm² mm² mm²

Micro-Breaker A A A A A

mm²

mm²4,mm²

5.0 6.0 8.0 12.0

10.0

Main Switch

Meter 485-

Meter 485+

L1 L2 L3

Grid

Load

Communica�on Ports for Meter

Fox Hybrid and AC Charger H3 and AC3 Installation guide

Fox Hybrid and AC Charger H3 and AC3 Installation guide

Fox Hybrid and AC Charger H3 and AC3 Installation guide

Other documents