Quick Installaon Guide
0.7-3.3kW Single Phase Inverter
1. Packing List
A B C D E
F G H I J
Quick
Guide
K
L
M
N
Manual
Step 1: Fix the bracket on the wall
Drill holes with electric drill, make
sure the holes are at least 50mm
deep, and then ghten the expansion
tubes.
Choose the place you want to install
the inverter. Place the bracket on the
wall and mark the posion of the 3
holes from bracket.
Please make sure the inverter will be installed with a proper distance
as shown below.
Posi�on Min Size
Le
Right
Top
Boom
Front
2. Inverter Installa�on
Step 2: Match the inverter with wall bracket
Hang the inverter over the bracket, slightly lower the inverter, and make
sure the two moun grooves on the back are properly xed with the
two bracket bars.
Model (kW) 0.7 1.0 1.5 2.0 2.5 3.0 3.3
Cable 2.5mm² 2.5mm² 2.5mm² 4mm² 4mm² 4mm² 4mm²
Micro-Breaker 16A 16A 16A 25A 25A 25A 25A
AC Wiring
-
Cable dimensions
3. Wiring Steps
Insert the expansion tubes into the holes
and ghten them. Install the bracket
with the expansion screws.
Note: Please refer to local cable type and color for actual installa
a. Hold the middle part of the female insert, rotate the back shell to
loosen it, and detach it from female inset.
b. Remove the cable nut (with rubber insert) from the back shell.
· Slide the cable nut,
then the back shell onto the cable.
-
Trim all the wires to 52.5mm and the PE wire to 55mm.
-
Use the crimping pliers to trim 12mm of insulaon from all wire ends
as shown in the picture.
· Separate the AC plug into three parts as below.
L: Brown/Red Wire
N: Blue/Black Wire
PE: Yellow & Green Wire
· Push the threaded sleeve into the socket,
ghten up the cap on the terminal.
DC Wiring
· Turn othe DC switch.
· Choose 12 AWG wire to connect the PV module.
· Trim 6mm of insularom the wire end.
· Separate the DC connector as below.
· Push the threaded sleeve to connecn terminal unl both are locked
ghtly on the inverter.
· Remove the AC connector, press the bayonet out of the slot with a
small screwdriver or the unlock tool and pull it out, or unscrew the
threaded sleeve, then pull it out.
· Insert striped cable into pin contact and ensure all conductor strands
are captured in the pin contact.
· Unlock the DC connector
- Use the specied wrench tool.
- When separa the DC + connector, push the tool down from the
top.
- When separag the DC - connector, push the tool down from the
bom.
- Separate the connectors by hand.
· Crimp pin contact by using a crimping plier. Put the pin contact with
striped cable into the corresponding crimping pliers and crimp the
contact.
· Insert pin contact through the cable nut to assemble into back of the
male or female plug. When you feel or hear a “click” the pin contact
assembly is seated correctly.
Grounding Wiring
Screw the ground screw with screwdriver as shown below.
4. Startup Procedure
V1.0
10-203-00152-00
Plug Pin contact cable nut
D-
D+
12
Object Quan�ty Descrip�on Object Quan�ty Descrip�on
A
Earth terminal 1H
Inverter1
B Bracket1
C DC connector (F/M)2
D AC connector1
E Expansion tube3
F Expansion screw3
G
DC pin contact
(1*posie, 1*negae)
2
Set screw1I
1J
K Product manual 1
1L
WiFi/LAN1M
N Unlock tool 1
4. Complete inverter Start-up guide
breakers.
energy, the LED will be green.
Note:
correct.
300mm
(11.8in)
300mm
(11.8in)
300mm
(11.8in)
300mm
(11.8in)
300mm
(11.8in)
300mm
(11.8in)
300mm
(11.8in)
300mm
(11.8in)
300mm
(11.8in)
O
P
O1
P1
-
1
-
2
FOX-ESS 0.7-3.3kW Single Phase Inverter Installation guide
- Type
- Installation guide
- This manual is also suitable for
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI
Other documents
-
Energizer Force 3S Installation guide
-
FoxESS 11 KW Installation guide
-
Fox Hybrid and AC Charger H3 and AC3 Installation guide
-
CPS SCA60KTL-DO/US-480 Operating instructions
-
CPS SCA23KTL-DO/US-480 Operating instructions
-
YASKAWA PVI 36TL Operating instructions
-
-
SunPower RESERVE-INV-1-P5-L1-INT Solar Storage Battery Installation guide
-
Broseley F-0710X2 series Installation guide
-
Premier MAMBA Assembly Manual
