Altronix TROVE Trove1M1WP Installation guide

TROVE Trove1M1WP
Altronix
Brand
Altronix
Model
TROVE Trove1M1WP
Type
Installation guide

This manual is also suitable for

Altronix TROVE Trove1M1WP offers a secure and versatile solution for integrating access control and power systems outdoors. With its NEMA 4/IP 66-rated enclosure, it protects sensitive electronic components from harsh weather conditions. The backplane accommodates various combinations of Mercury/LenelS2 boards, allowing for customized access control configurations. Additionally, it supports Altronix power supplies and sub-assemblies, enabling power and battery backup integration.

Altronix TROVE Trove1M1WP offers a secure and versatile solution for integrating access control and power systems outdoors. With its NEMA 4/IP 66-rated enclosure, it protects sensitive electronic components from harsh weather conditions. The backplane accommodates various combinations of Mercury/LenelS2 boards, allowing for customized access control configurations. Additionally, it supports Altronix power supplies and sub-assemblies, enabling power and battery backup integration.

Trove1M1WP
- NEMA 4/IP 66 Rated outdoor enclosure with Altronix and Mercury/LenelS2 backplane
TM1X
- Altronix/Mercury/LenelS2 backplane only
Access & Power Integration
Rev. T1M1WP121919
Installing Company: _________________________ Service Rep. Name: __________________________________________
Address: _________________________________________________________ Phone #: _________________________
All registered trademarks are property of their respective owners.
Installation Guide
More than just power.™
Access & Power Integration
- 2 - Trove1M1WP / TM1X Installation Guide
Overview:
Altronix Trove1M1WP accommodates various combinations of Mercury/LenelS2 boards with or without Altronix power supplies and sub-assemblies
for access systems in a NEMA 4/IP 66 Rated outdoor enclosure.
Specifications:
Trove1M1WP :
Outdoor enclosure with TM1X Altronix/Mercury/LenelS2 backplane.
Accommodates the following Mercury/LenelS2 controllers:
LP1501, MR51e, MR50, LP1502, MR4502, MR52, MR16IN, MR16OUT, LP2500, MUX8
Accommodates the following Altronix power supplies and/or sub-assemblies: eFlow or ULX Power Supply/Chargers, AL175ULB, T2428100,
ACM4, ACM4CB, VR6, PDS8, PDS8CB, PD4UL, PD4ULCB, PD8UL or PD8ULCB
• 16 Gauge Backplane (TM1X):
- Dimensions (H x W x D): 14.875” x 12.875” x 0.3125” (377.8mm x 327mm x 7.9mm).
• Enclosure (WP2):
- Hot compression molded, halogen free, self-extinguishing fiberglass reinforced polyester.
- Stainless steel continuous hinge and stainless steel padlockable latches.
- Dimensions (H x W x D): 17.53” x 15.3” x 6.67” (445.3mm x 388.6mm x 169.4mm).
• Includes mounting hardware.
TM1X:
16 Gauge Backplane.
Accommodates the following Mercury/LenelS2 controllers:
LP1501, MR51e, MR50, LP1502, MR4502, MR52, MR16IN, MR16OUT, LP2500, MUX8
Accommodates the following Altronix power supplies and/or sub-assemblies: eFlow or ULX Power Supply/Chargers, AL175ULB, T2428100,
ACM4, ACM4CB, VR6, PDS8, PDS8CB, PD4UL, PD4ULCB, PD8UL or PD8ULCB.
- Dimensions (H x W x D): 14.875” x 12.875” x 0.3125” (377.8mm x 327mm x 7.9mm).
See TM1X Position Charts on Pg. 3 for the list of compatible power supplies and sub-assemblies.
Battery Backup:
• Trove1M1WP enclosure accommodates up to two (2) 12VDC/7AH batteries.
Accessories
PMK2 Pole Mount Kit (order separately)
PMK2 pole mount kit is designed to simplify installation of outdoor units. It accommodates 2”- 8”(diameter) poles or 5” (127mm) square poles.
Kit includes:
- Two (2) powder coated steel mount brackets.
- Four (4) stainless steel bolts and lock washers.
- Two (2) wormgear quick release straps.
Installation Instructions:
Wiring methods shall be in accordance with the National Electrical Code/NFPA 70/ANSI and with all local codes and authorities having jurisdiction.
Product is intended for indoor use only.
1. Remove backplane from enclosure prior to drilling. Do not discard hardware.
Note: Make sure that hardware will not interfere with components of the circuit board.
2. Mark and drill desired inlets on the enclosure to facilitate wiring. Maximum NEMA type 4X rated fittings to be used are 0.5”.
Follow manufacturer’s specifications for the appropriate size opening.
Note: Inlets for conduit fittings should only be made on the bottom of the enclosure.
UL Listed NEMA type 4X rated conduit connector/hubs shall be used for the appropriate size inlets.
3. Mounting NEMA4/4X rated enclosure (Enclosure Dimensions, pg. 8):
Wall mount: Mount unit in desired location. Mark and drill holes to line up with the top and bottom holes of the enclosure flange.
Secure enclosure with appropriate fasteners (e. g. screws and anchors; bolts and locking nuts, etc.) that are compatible
with mounting surface and are of sufficient length/construction to ensure a secure mount (Fig. 3, pg. 6).
Pole Mount: Refer to Figs. 4 - 8, pg. 6.
Note: All inlets for conduit fittings should be on the bottom of the enclosure.
4. To facilitate wire entry utilize weather-tight NEMA rated connectors, bushings, and cable.
Trove1M1WP / TM1X Installation Guide - 3 -
Installation Instructions for Sub-Assemblies to Trove1M1WP/TM1X:
Altronix Power Supplies/Chargers and/or Sub-Assemblies:
1a. Power Supply/Charger:
Fasten two (2) nylon and two (2) metal standoffs (supplied) to pem location (1) (Fig. 1, pg. 4).
Secure board to standoffs using pan head screws (supplied) (Fig. 1a, pg. 4).
1b. T2428100 Transformer:
Position transformer on pem location (3) as shown in Fig. 2, pg. 5. Secure transformer to backplane using two (2) lock nuts (supplied).
2. Sub-Assemblies:
Fasten standoffs (supplied) to pem location (2) as shown on Fig. 1, 2, pg. 4, 5.
Secure boards to standoffs using pan head screws (supplied) (Fig. 1a, 2a, pg. 4, 5).
3. For detailed information about installing and connecting Altronix sub-assemblies refer to the individual Installation Guides.
Mercury/LenelS2 Sub-Assemblies:
4. Fasten standoffs (supplied) to pem locations (A), (B), (C) or (D) as shown on Fig. 1, 2, pg. 4, 5 depending on the sub-assembly module.
5. Secure boards to standoffs using pan head screws (supplied).
6. Fasten backplane to WP2 enclosure utilizing provided hardware.
Position Chart for the Following Altronix Models:
Altronix Board Pem Mounting
AL400ULXB2, AL600ULXB, AL1012ULXB, AL1024ULXB2, eFlow4NB, eFlow6NB, eFlow102NB, eFlow104NB 1
AL175ULB, ACM4, ACM4CB, VR6, PDS8, PDS8CB, PD4UL, PD4ULCB, PD8UL or PD8ULCB 2
T2428100 3
Position Chart for the Following Mercury/LenelS2 Models:
Mercury/LenelS2 Access Controller Pem Mounting
LP1502, LP4502, MR52, MR16IN, MR16OUT A
LP2500, MUX8 B
LP2500, MUX8 C
LP1501, MR62e D
- 4 - Trove1M1WP / TM1X Installation Guide
2
1
Metal
Spacer
Placement
Nylon
Spacer
Placement
C
D
A
B
Pem
Spacer
Backplane
Pan Head
Screw
Sub-Assembly
Fig. 1a
Fig. 1
Trove1M1WP / TM1X Installation Guide - 5 -
2 2
3
A
B
CD
Fig. 2
Pem
Spacer
Backplane
Pan Head
Screw
Sub-Assembly
Fig. 1a
- 6 - Trove1M1WP / TM1X Installation Guide
Wall Mount Installation
1- Place unit at desired location and secure with mounting
screws (not included) (Fig. 3, pg. 6).
Fig. 3
Pole Mounting Using Optional Pole Mount Kit PMK2 (not included):
This installation should be made by qualified service personnel. This product contains no serviceable parts. PMK2 is intended for use with Altronix
outdoor rated power supplies or accessories housed in WP2 enclosures. Brackets are designed for use with the Wormgear Quick Release Straps
(two included).
1. Thread one (1) wormgear quick release strap through the slots on the back of a mounting bracket (Fig. 4, pg. 6).
2. Once the desired height of the top Pole Mount bracket is achieved, tighten the straps down by sliding open end of the strap through the
locking mechanism on the strap, then tighten the screw with flat head screwdriver or 5/16” hex socket driver
(Fig. 5, pg. 6 and Fig. 7, pg. 6).
3. Attach the bottom bracket to the enclosure by inserting bolts through the flange of the enclosure and into the bracket, tightening bolts
with a 7/16” hex socket (Fig. 6, pg. 6).
4. Thread the second wormgear quick release strap through the slots on the back of the bottom mounting bracket (Fig. 4, pg. 6).
5. Mount enclosure onto the top bracket by inserting bolts through flange of the enclosure and into the bracket, tightening bolts with a
7/16” hex socket (Fig. 6, pg. 6).
6. Tighten the straps of the bottom bracket down by sliding the open end of the strap through the locking mechanism on the strap, then
tighten screw with flat head screwdriver or 5/16” hex socket driver (Fig. 4, pg. 6).
7. Clip excess straps.
Fig. 4 Fig. 5 Fig. 6
Fig. 7
Fig. 8
2” to 8”(50.8mm to 203.2mm)
diameter round pole
Fig. 8a
5” (127mm) square pole
Trove1M1WP / TM1X Installation Guide - 7 -
TM1X Drawing and Dimensions (H x W x D approx.):
10.75” x 8.875” x 2.375” (273.1mm x 225.4mm x 60.3mm)
8.875” (225.4mm)
8.25” (209.5mm)
0.25”
(6.4mm)
10.75” (273.1mm)
10.25” (260.3mm)
- 8 - Trove1M1WP / TM1X Installation Guide
Altronix is not responsible for any typographical errors.
140 58th Street, Brooklyn, New York 11220 USA | phone: 718-567-8181 | fax: 718-567-9056
web site: www.altronix.com | e-mail: [email protected]
IITrove1M1WP / TM1X G14U MEMBER
Enclosure Dimensions (H x W x D approximate):
17.53” x 15.3” x 6.67” (445.3mm x 388.6mm x 169.4mm)
FRONT VIEW COVER REMOVED
RIGHT SIDE VIEWFRONT VIEW
END VIEW
SECTION A-A
AA
316 STAINLESS STEEL PADLOCK LATCH
ATTACHED WITH RIVETS. Ø 0.375 PADLOCK EYE
17.36” (441 mm)
12.00” (304.8mm)
6.41” (162.8mm)
10-32 X 0.250 BRASS INSERT 4 PLCS.
14.54” (369.3mm)
16.74” (425.2mm)
0.125” (3.2mm)
14.25” (362mm)
14.00” (355.6mm)
12.23” (310.6mm)
17.53” (445.3mm)
16.00” (406.4mm)
1.67” (42.4mm) 5.00” (127mm)
16.73” (425mm)
15.3” (388.6mm)
6.67” (169.4mm)
4.94” (125.5mm)
5.77” (146.6mm)
0.75” (19.1mm)
MOUNTING PLATE
Ø 0.32” (8.1mm)
WALL MOUNTING HOLE X 4
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8

Altronix TROVE Trove1M1WP Installation guide

TROVE Trove1M1WP
Altronix
Brand
Altronix
Model
TROVE Trove1M1WP
Type
Installation guide
This manual is also suitable for

Altronix TROVE Trove1M1WP offers a secure and versatile solution for integrating access control and power systems outdoors. With its NEMA 4/IP 66-rated enclosure, it protects sensitive electronic components from harsh weather conditions. The backplane accommodates various combinations of Mercury/LenelS2 boards, allowing for customized access control configurations. Additionally, it supports Altronix power supplies and sub-assemblies, enabling power and battery backup integration.

Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents