Retrofit kit No. 84 61 0 143 955
Installation Instructions No. 01 29 0 146 555 Issue date: 04.2002
BMW Apollo car phone retrofit kit
BMW 3 Series Convertible (E
46/C)
The installation time is approx. 5 hours, but this may vary depending on the condition of the car and the
equipment in it.
Retrofit kit No. 84 61 0 143 955
Parts and Accessories
Installation Instructions
046 0627 Z
EN/2
Retrofit kit No. 84 61 0 143 955
Installation Instructions No. 01 29 0 146 555 Issue date: 04.2002
Contents
Section Page
Important information. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
1. Preparations. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
2. Retrofit wiring harness connection diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
3. Installation and cabling diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
4. To install and connect the retrofit wiring harness . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
5. To install and connect the transceiver module . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
6. To install and connect the eject box . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
7. To install the hands-free microphone . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
8. Concluding work . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
9. Circuit diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
EN/3
Retrofit kit No. 84 61 0 143 955
Installation Instructions No. 01 29 0 146 555 Issue date: 04.2002
Important information
Only for use in the BMW dealer organisation.
Subject to technical modifications.
Installation information
Ensure that the cables/lines are not kinked or damaged as you install them in the car.
If the specified PIN chambers are occupied, bridges, double crimps or twin-lead terminals must be used.
Target group
The target group for these installation instructions is specialist personnel trained on BMW cars with the
appropriate specialist knowledge.
All work must be completed using the latest BMW repair manuals, circuit diagrams, servicing manuals and
work instructions in a rational order using the prescribed tools (special tools) and observing current health and
safety regulations.
Ordering instructions
A black insert for the centre console is supplied in the retrofit kit.
An insert for the centre console in other colours for cars with different interior colours can be ordered if
required. See the EPC for all further ordering information.
Safety instructions
Refer to the safety instructions for handling components of the airbag system. Further information is available
in the TIS in RA No. 32 34 ... If you fail to follow the safety instructions the airbag system may deploy
incorrectly and cause injuries.
List of special equipment
The following special equipment must be taken into consideration when installing the mobile phone.
SA 602
On-board monitor
SA 606
Radio navigation system
SA 609
Navigation system
SA 660
BMW Reverse radio
SA 661
BMW Business radio
SA 662
BMW Business CD radio
SA 663
BMW Professional radio
Special tools required
DIS or MoDiC III
EN/4
Retrofit kit No. 84 61 0 143 955
Installation Instructions No. 01 29 0 146 555 Issue date: 04.2002
1. Preparations
0
TIS instruction No.
Conduct a brief test
Disconnect the negative pole of the battery 12 00 ...
The following components must be removed first of all:
Boot trim on the left 51 47 151
Rear seat bench 51 24 005
Rear seat backrest 51 24 010
Front left door sill trim 51 47 000
Rear left side trim 51 43 015
Front left seat 52 .. ...
B pillar trim at the bottom left 51 43 150
Glove box, left 51 16 350
Pedal trim 51 15 185
A pillar trim in the left footwell 51 43 070
A pillar trim on the left 51 43 201
Left sun visor 51 16 080
Interior light 63 31 000
Glove box with casing, right 51 16 366
Oddments box support 51 16 ...
Finishing strips, centre and right 51 10 221
Heating system control 64 11 748
Radio 65 11 030
Oddments box 51 16 200
EN/5
Retrofit kit No. 84 61 0 143 955
Installation Instructions No. 01 29 0 146 555 Issue date: 04.2002
2. Retrofit wiring harness connection diagram
0
0
Item Description Signal
Cable colour /
Cross-section
Connection location in the car Abbreviation / Slot
A Multi wiring harness --- --- --- ---
A1 SW 54-pin plug --- --- To transceiver module adapter branch
B1
X4038
A2 Fakra plug contact --- --- Insulate and tie back X13323
A3 SW 18-pin plug --- --- To eject box adapter branch
C1
X4545
A4 Fakra plug contact --- --- Insulate and tie back X13322
A5 SW 10-pin plug LSP
---
Cars with SA 660/661/662 only
To t he radio plug
X13598
A6 Socket contact
Mute
Te l -On
WS/BR
0.35 mm
2
WS/GN
0.35 mm
2
Cars with SA 660/661/662 only
To the radio plug X18126
PIN 4
X18126
PIN 10
A7 Twin-lead terminal
SW 8-pin plug
--- ---
Between audio plugs X322
A8 SW 3-pin plug Mic --- To hands-free microphone X13293
A9 SW 3-pin plug --- --- To the aerial booster X1765
A10 Cable eyelet Terminal 31 --- To the earth post in the boot on the left X13016
A11 SW 12-pin plug LSP
---
Cars with SA 602/606/609/663 only
To radio receiver plug X13321
A12 Socket contact
Mute
Te l -On
WS/BR
0.35 mm
2
WS/GN
0.35 mm
2
Cars with SA 602/606/609/663 only
To radio receiver plug X18126
PIN 10
X18772
PIN 11
A1
A12
A11
A5
A6
A3
A
A4
A2
A7
A8
A10
A9
046 0490 Z
EN/6
Retrofit kit No. 84 61 0 143 955
Installation Instructions No. 01 29 0 146 555 Issue date: 04.2002
2. Retrofit wiring harness connection diagram
0
0
Item Description Signal
Cable colour /
Cross-section
Connection location in the car Abbreviation / Slot
BTransceiver module adapter --- --- --- ---
B1 SW 54-pin plug --- --- To multi wiring harness branch
A1
X4038
B2 SW 25-pin plug --- --- To transceiver module X695
CAdapter eject box --- --- --- ---
C1 SW 18-pin plug --- --- To multi wiring harness branch
A3
X4545
C2 SW 18-pin plug --- --- To interface X4545
--- ---
DAerial adapter --- --- --- ---
D1 FAKRA plug contact --- --- To standard aerial cable ---
D2 Mini UHF plug contact --- --- To transceiver module ---
046 0619 Z
A2
A
A1
B1
B2
B
C1 C2
C
EN/7
Retrofit kit No. 84 61 0 143 955
Installation Instructions No. 01 29 0 146 555 Issue date: 04.2002
3. Installation and cabling diagram
0
Legend
A Multi wiring harness II
BTransceiver module adapter
CAdapter eject box
0
1Radio plug
X18126
(with SA 660, 661, 662 only)
2 Hands-free microphone
3Eject box and interface
4Audio plug
X322
5Transceiver module
6Radio plug
X18126
(with SA 602, 606, 609, 663 only)
7 Earth post
X13016
046 0761 Z
2
3
6
7
B
A
4
1
5
C
EN/8
Retrofit kit No. 84 61 0 143 955
Installation Instructions No. 01 29 0 146 555 Issue date: 04.2002
4. To install and connect the retrofit wiring harness
0
0
0
0
0
Install branches
A1 – A8
as follows:
-Branches
A1
-
A2
to the installation site of the
transceiver module behind the rear seat backrest on
the left
-Branches
A3
-
A8
to the left side skirt
-Branches
A9
-
A12
through the cable duct (1) into the
boot on the left
0
Connect branches
A1
and
B1
.
Wrap both plug connections in safety strips (1).
0
Screw branch
A10
to earth post
X13016
.
Cars with SA 660/661/662 only
Insulate branches
A11
and
A12
and tie them back.
Cars with SA 602/606/609/663 only
Lay plug
X18126
to the radio receiver.
0
Disconnect plug
X18126
from the radio receiver (1).
A1
A2
A3-A8
A9-A12
1
1
B1
A1
046 0498 Z
A10
A10
X13016
A11-A12
X18126
1
046 0723 Z
EN/9
Retrofit kit No. 84 61 0 143 955
Installation Instructions No. 01 29 0 146 555 Issue date: 04.2002
4. To install and connect the retrofit wiring harness
0
0
0
0
0
Connect branch
A12
as follows to plug
X18126
:
- WS/BR cable in PIN 10
- WS/GN cable in PIN 11
0
Connect branch
A11
to plug
X18126
.
If the plug
X13321
is already in the car, the two
cables from branch
A9
must be disconnected and
connected to the same pins in the plug in the car
X13321
.
0
All cars
Install branches
A3 – A8
as follows:
-Branches
A3
and
A4
to the centre console.
-Branch
A8
to the A pillar.
Cars with SA 660/661/662 only
-Branches
A5 – A7
to the radio.
Cars with SA 602/606/609/663 only
-Insulate branches
A5
and
A6
and tie them back.
0
All cars
Lay branch
A8
to the installation site of the hands-free
microphone.
A12
X18126
046 0724 Z
A11
X18126
046 0725 Z
A8
A3-A4
A5-A7
A8
EN/10
Retrofit kit No. 84 61 0 143 955
Installation Instructions No. 01 29 0 146 555 Issue date: 04.2002
4. To install and connect the retrofit wiring harness
0
0
0
0
Disconnect plug
X322
.
Connect branch
A7
in parallel between plug
X322
.
0
Cars with SA 660/661/662 only
Connect branch
A6
as follows to plug
X18126
:
- WS/BR cable in PIN 4
- WS/GN cable in PIN 10
0
Connect branch
A5
to plug
X18126
.
If the plug
X13321
is already in the car, the two
cables from branch
A9
must be disconnected and
connected to the same pins in the plug in the car
X13321
.
X322
A7
X322
046 0540 Z
X18126
A6
X18126
A5
EN/11
Retrofit kit No. 84 61 0 143 955
Installation Instructions No. 01 29 0 146 555 Issue date: 04.2002
5. To install and connect the transceiver module
0
0
0
0
0
Insert the transceiver module (1) into the holder (2) and
secure the bar (3) with hexagonal screw (4).
0
Bolt the strut (1) to the holder (3) using a hexagonal screw (2).
0
Connect branch
B2
to the transceiver module (1).
Connect the aerial adapter
C
between the transceiver
module (1) and standard aerial cable (2).
0
Insert the holder with the transceiver module (1) into left
rear panel (2) and secure it with hexagonal screws (3).
2
3
4
1
046 0329 Z
2
1
3
046 0330 Z
1
B2
B
C
2
046 0331 Z
1
2
3
046 0332 Z
EN/12
Retrofit kit No. 84 61 0 143 955
Installation Instructions No. 01 29 0 146 555 Issue date: 04.2002
6. To install and connect the eject box
0
0
0
0
0
Connect the telephone cable (1) to the eject box (2).
Insert the telephone cable (1) into the cable guide (3) and
clip the cable guide (3) together.
0
Clip the eject box (1) into the frame console (2).
0
Clip the cable guide (1) into the frame console (2).
0
Clip the frame console with the eject box (1) into the
oddments box (2).
3
1
2
046 0308 Z
1
2
046 0309 Z
1
2
046 0310 Z
1
2
046 0311 Z
EN/13
Retrofit kit No. 84 61 0 143 955
Installation Instructions No. 01 29 0 146 555 Issue date: 04.2002
6. To install and connect the eject box
0
0
0
0
0
Affix the foam strip (1) to the inside of the holder frame (2).
Place the interface (3) on the oddments box (4) and clip in
the holder frame (2).
0
Connect the black 12-pin plug (1) for the eject box to the
interface (2).
Connect the black 6-pin plug (3) for the eject box to the
black 6-pin plug (4) for the interface (2).
0
The adapter cable C must be fitted.
Connect the eject box adapter C between the black 18-
pin plug (1) on the interface and branch A3.
0
Wrap the plug connectors (1) in safety strips (2).
3
1
2
4
046 0312 Z
1
2
3
4
046 0313 Z
1
A3
C
1
2
EN/14
Retrofit kit No. 84 61 0 143 955
Installation Instructions No. 01 29 0 146 555 Issue date: 04.2002
7. To install the hands-free microphone
0
0
Connect branch A8 to the hands-free microphone (1).
The arrow on the hands-free microphone (1) must
point to the front of the car.
Clip the hands-free microphone (1) into the ceiling light (2).
2
1
A8
EN/15
Retrofit kit No. 84 61 0 143 955
Installation Instructions No. 01 29 0 146 555 Issue date: 04.2002
8. Concluding work
This retrofit system does not require coding.
- Conduct a brief test with DIS/MoDiC III.
- Conduct a function test
- Re-assemble the car
EN/16
Retrofit kit No. 84 61 0 143 955
Installation Instructions No. 01 29 0 146 555 Issue date: 04.2002
9. Circuit diagram
The circuit diagrams for the retrofit telephone system are available if required on the installation
instructions CD entitled “Circuit diagrams for retrofit telephones UNI II”.
/