Page is loading ...
Retrofit / Installation kit No. 82 83 0 136 518
Installation Instructions No. 01 29 0 136 536 Issue date: 10.2001
Sound Module system retrofit kit
BMW 3 Series compact (E
46/5) LHD
The Sound Module system is only suitable for installation in cars
without SA676
BMW Hi-fi
system.
Technical and electrical knowledge required
The installation time is approx. 3.5 hours but this may vary depending on the condition of the
car and the equipment in it.
Retrofit / Installation kit No. 82 83 136,518
Parts and Accessories
Installation Instructions
046 0621 B
EN/2
Retrofit / Installation kit No. 82 83 0 136 518
Installation Instructions No. 01 29 0 136 536 Issue date: 10.2001
Contents
Section Page
1. Important information for the installation of the Sound Module . . . . . . . . . . . . . . . . 3
2. Preparations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
3. Parts list . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
4. To install the amplifier and additional wiring harness
(for cars with a battery in the engine compartment) . . . . . . . . . . . . . . . . . . . . . . . . . 7
5. To install the amplifier and additional wiring harness
(for cars with a battery in the boot) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
6. To install the amplifier and additional wiring harness
(for cars with a battery in the engine compartment)
with an on-board monitor radio . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
7. To install the amplifier and additional wiring harness
(for cars with a battery in the boot) with an on-board monitor radio . . . . . . . . . . . . . 21
8. To install the tweeters and woofers/mid-range speakers in the front . . . . . . . . . . . 26
9. To install the tweeters and woofers/mid-range speakers in the rear . . . . . . . . . . . . 27
10. Templates for rear tweeters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30
11. Templates for airbag mounting plate . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31
12. Coding/Concluding work . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32
EN/3
Retrofit / Installation kit No. 82 83 0 136 518
Installation Instructions No. 01 29 0 136 536 Issue date: 10.2001
1. Important information for the installation of the Sound Module system3
Only for use in the BMW dealer organisation.
The Sound Module system may only be installed by a specialist workshop that has the required
special tools and manuals (servicing, repair, diagnostics, etc.).
This high quality audio system is to be fitted exclusively in conjunction with original BMW
car radios.
The customer information is to be given to the customer.
If it is connected to other makes, BMW AG cannot accept any guarantee for the sound module
system.
The Sound Module system is only suitable for installation in cars
without SA676
BMW Hi-fi
system..
Ensure that the cables/lines are not kinked or damaged as you install them in the car.
Additional cables/lines that you install must be secured with cable ties.
Item numbers refer only to the overview drawings and to the texts next to the appropriate figure.
Electrical knowledge is required.
Use the radio/amplifier adapter cable
C
in cars with an on-board monitor radio with a
production date after 9/01 (New Generation radio connection plug).
During installation, proceed in the same way as when installing the radio/amplifier adapter
cable
A
.
The top section on the left and right of the rear speaker mounting box is not supplied in
the retrofit kit and must be ordered separately to match the vehicle equipment (interior
equipment) using the electronic arts catalogue (EPC) (a new part is required).
Subject to technical modifications
Required tools and equipment
1/4 inch socket set Set of Philips screwdrivers
Crimping pliers Cable lamp
Set of flat screwdrivers Angle cutter
Set of Torx sockets Combination pliers
Set of drill bits Drill
Textile adhesive tape Sealing compound
Pneumatic grinders with milling insert
EN/4
Retrofit / Installation kit No. 82 83 0 136 518
Installation Instructions No. 01 29 0 136 536 Issue date: 10.2001
2. Preparations
0
TIS instruction No.
Conduct a brief test (print out error memory)
---
Disconnect the battery 12 00 ...
Remove the left footwell trim
---
Remove the oddments box on the left of the steering column
---
Remove the décor strips on the left and centre
---
Remove the light switch unit
---
Remove the radio
---
Remove the control module cover in the engine compartment
---
Remove the rear seat bench
---
Remove the rear seat backrest parts on both sides
---
Remove the side trim at the rear left and rear right
---
Remove the boot carpet and the foam mat beneath it
---
Remove the closing panel trim in the boot
---
Remove the boot trims on both sides
---
Remove the seat belt cover at the top left and top right
---
Remove the C pillar covers on both sides
---
Remove the mounting box for the rear speakers on both sides
---
Remove the mounting boxes for the rear speakers (top and bottom
sections; the top sections are no longer required)
---
Remove the rear speakers on both sides
(no longer required)
---
Remove the door trims on both sides
---
Undo the covers on the tweeters at both sides
---
Remove the tweeters (no longer required)
---
Remove the front door speakers on both sides (no longer required)
---
Additional work for cars with the battery in the engine
compartment
---
Remove the battery cover
---
---
Additional work for cars with the battery in the boot
---
Remove the left door sill strip
---
Remove the A pillar trim at the bottom left (footrest)
---
---
Additional work for cars with an on-board monitor radio
---
Remove the rear left airbag (if fitted)
---
Remove the rear left airbag mounting plate
---
Remove the on-board monitor radio
---
EN/5
Retrofit / Installation kit No. 82 83 0 136 518
Installation Instructions No. 01 29 0 136 536 Issue date: 10.2001
3. Parts list
0
Legend
0
ARadio/Amplifier adapter cable
BPower supply cable with fuse
CRadio/amplifier adapter cable
only for cars with an on-board monitor radio after production date 09/01
1 Amplifier
2 Fillister head self-tapping screw 3.5x9.5 for amplifier holder (8x)
3 Adapter for earth connection
4Hexagonal lock nut M6
5Bottom amplifier holder
6 Top amplifier holder
7Pipe clip
8Hexagonal screw M8x20
9Hexagonal nut with collar M8
10 Damping strip
11 Blade terminal contact for adapter cable power lead
12 Front woofer/mid-range speaker (2x)
13 Rear woofer/mid-range speaker (2x)
1
2
3
A
B
4
89 10
567
C
11 12 13
046 0865 B
EN/6
Retrofit / Installation kit No. 82 83 0 136 518
Installation Instructions No. 01 29 0 136 536 Issue date: 10.2001
3. Parts list
0
Legend
0
14 Front tweeter (2x)
15 Rear tweeter (2x)
16 Washer 4.3 mm (4x)
17 Lock nut M4 (4x)
18 Cable tie (20x)
19 Double insulation-piercing connector (2x)
20 Top section of rear speaker mounting box, right*
21 Top section of rear speaker mounting box, left*
22 Template for rear tweeter, left
23 Template for rear tweeter, right
24 Customer information
25 Installation instructions (on the installation instructions CD)
26 Template for airbag mounting plate
27 Template for airbag mounting plate
28 Foam hose 150 mm (2x)
Parts marked with an asterisk (*) are not supplied with the retrofit kit and must be ordered
separately to match the car’s equipment (interior equipment) using the electronic parts
catalogue (EPC).
BMW
Einbauanleitung
Kunden
information
14
20 21 22 23
24 25 26 27 28
15 16 17 18 19
046 0805 B
left
right
EN/7
Retrofit / Installation kit No. 82 83 0 136 518
Installation Instructions No. 01 29 0 136 536 Issue date: 10.2001
4. To install the amplifier and additional wiring harness
(for cars with a battery in the boot)
0
0
0
0
0
Push the hexagonal screw M8x20 (8) into the top
amplifier holder (6) from underneath.
Place the top amplifier holder (6) with the inserted
hexagonal screw M8x20 (8) on to the amplifier (1)
and secure it with four fillister head screws 3.5x9.5
(2).
Watch the position of the opening (40) for the
adapter cable connection plug.
0
Affix the damping strip (10) on to the top amplifier
holder (6) and the amplifier (1) as shown in the
figure.
0
The figure shows the driver’s footwell with a
view through the opening in the left
oddments box next to the steering column.
Fit the pipe clip (7) to the cross strut (40) on the
instrument panel holder.
Cut out the insulation mat (41) above the securing
screw (42) for the control module box and unscrew
the securing screw (42).
If the Telestart receiver for a retrofit auxiliary
heating system is fitted in this position it must
be removed.
0
Screw the bottom amplifier holder (5) into the hole
(41) provided using the existing securing screw
(40) for the control module box.
Do not tighten the securing screw (40) yet
since otherwise it will be difficult to slide in
the amplifier.
1
2
40
8
6
046 0623 B
1
6
10
046 0624 B
40
42
7
41
046 0625 B
40
41
5
046 0626 B
EN/8
Retrofit / Installation kit No. 82 83 0 136 518
Installation Instructions No. 01 29 0 136 536 Issue date: 10.2001
4. To install the amplifier and additional wiring harness (for cars with a battery in the boot)
0
0
0
0
0
Connect the black 17-pin radio connection plug
X18126
to the black 17-pin plug casing (40) on
adapter cable
A
.
You may have to reconnect the CD changer
connection cable to the black 17-pin socket
casing (41) on the adapter cable
A
.
Connect the black 17-pin socket casing (41) on
the adapter cable
A
to the radio.
Then lay the adapter cable
A
with the black 25-pin
connection plug (42), as shown in the figure, above
the steering column to the installation site of the
amplifier and secure it with cable ties.
0
Connect the adapter cable
A
to the amplifier (1).
Attach the 25-pin connection plug (40) on the
adapter cable
A
to the plug strip (41) and press it
in the direction indicated by the arrow with a large
flat screwdriver (42) until it audibly engages in the
amplifier casing.
0
Carefully slide the connected, assembled amplifier
(1) behind the cross strut (40) and above the
bottom amplifier holder (5).
As you slide in the amplifier, ensure that you
do not jam or damage any of the cables. The
sequence of the following installation work
must be followed to the letter.
Place a hexagonal screw M8x20 (8) into the pipe
clip (7) and screw on a hexagonal nut with collar
M8 (9).
Do not tighten the nut yet.
B
M
W
41
40
X18126
A
42
046 0627 B
40
41
40
A
42
1
046 0628 B
5
1
40
8
7
9
046 0629 B
EN/9
Retrofit / Installation kit No. 82 83 0 136 518
Installation Instructions No. 01 29 0 136 536 Issue date: 10.2001
4. To install the amplifier and additional wiring harness (for cars with a battery in the boot)
0
0
0
0
0
Secure the bottom amplifier holder (5) to the
amplifier (1) with the two fillister head self-tapping
screws 3.5 x 9.5 (2).
Secure the adapter cable A along the main wiring
harness (40) with cable ties (18).
Align the amplifier (1) and ensure that you do not
jam or damage any of the cables. Then tighten the
securing screw (41) for the control module box and
the hexagonal nut with collar M8 (9).
If the car has an auxiliary heating system,
now reinstall the Telestart receiver you
removed earlier.
0
The figure shows the engine compartment on
the right near the control module box.
Secure the adapter for the earth connection (3) to
the earth post (40) near the brake booster using
the existing hexagonal nut M8.
0
Lay the earth cable (40), brown cable, with the 6
mm cable eyelet and the power cable (41), red
cable on the adapter cable A through the opening
(42) into the control module box in the engine
compartment on the left.
0
Carefully cut open the rubber grommet (40) in the
front a little.Carefully push the earth cable (41),
brown cable with 6 mm cable eyelet, through the
opening you have made in the rubber grommet
(40).Then secure the 6 mm cable eyelet (42) to the
adapter for the earth connection (3) using the
hexagonal nut M6 (4).
Seal the rubber grommet (40) around the
opening you cut using sealing compound.
5
1
2
9
A
40
41
18
046 0630 B
3
40
046 0631 B
41
A
40
42
046 0632 B
42
40
3
41
4
046 0633 B
EN/10
Retrofit / Installation kit No. 82 83 0 136 518
Installation Instructions No. 01 29 0 136 536 Issue date: 10.2001
4. To install the amplifier and additional wiring harness
(for cars with a battery in the engine compartment
0
0
0
0
0
Carefully cut open the rubber grommet (40) in the
front a little.Carefully push the power cable (41),
red cable, through the opening you have made in
the rubber grommet (40) and then push it through
the rubber grommet (42).
Seal the rubber grommet (40) around the
opening you cut using sealing compound.
0
Lay the power cable (40), red cable, under the
cable guide (41) from the left to the right side of the
car.Then on the right-hand side of the car push it
through the rubber grommet (42) to the installation
site of the battery.
0
Lay the power cable (40), red cable, to the
connection site of the supply cable with fuse B and
cut off the excess length.
Crimp the blade terminal contact (11) on to cut off
power cable (40) and connect it to the supply
cable with fuse B.Secure the cable eyelet, 8 mm in
diameter (41) on the supply cable with fuse B to
the positive pole on the battery.The secure the
supply cable with fuse B and the power cable (40)
with cable ties (18).
41
40
42
046 0634 B
40
4041
42
40
046 0635 B
046 0636 B
40
B
18
41
11
EN/11
Retrofit / Installation kit No. 82 83 0 136 518
Installation Instructions No. 01 29 0 136 536 Issue date: 10.2001
5. To install the amplifier and additional wiring harness
(for cars with a battery in the boot)
0
0
0
0
Push the hexagonal screw M8x20 (8) into the top
amplifier holder (6) from underneath.
Place the top amplifier holder (6) with the inserted
hexagonal screw M8x20 (8) on to the amplifier (1)
and secure it with four fillister head screws
3.5x9.5 (2).
Watch the position of the opening (40) for the
adapter cable connection plug.
0
Affix the damping strip (10) on to the top amplifier
holder (6) and the amplifier (1) as shown in the
figure.
0
The figure shows the driver’s footwell with a
view through the opening in the left
oddments box next to the steering column.
Fit the pipe clip (7) to the cross strut (40) on the
instrument panel holder.
Cut out the insulation mat (41) above the securing
screw (42) for the control module box and unscrew
the securing screw (42).
If the Telestart receiver for a retrofit auxiliary
heating system is fitted in this position it must
be removed.
0
Screw the bottom amplifier holder (5) into the hole
(41) provided using the existing securing screw
(40) for the control module box.
Do not tighten the securing screw (40) yet
since otherwise it will be difficult to slide in
the amplifier.
1
2
40
8
6
046 0637 B
1
6
10
046 0638 B
40
42
7
41
046 0639 B
40
41
5
046 0640 B
EN/12
Retrofit / Installation kit No. 82 83 0 136 518
Installation Instructions No. 01 29 0 136 536 Issue date: 10.2001
5. To install the amplifier and additional wiring harness (for cars with a battery in the boot)
0
0
0
0
Connect the black 17-pin radio connection plug
X18126 to the black 17-pin plug casing (40) on
adapter cable A.
You may have to reconnect the CD changer
connection cable to the black 17-pin socket
casing (41) on the adapter cable A.
Connect the black 17-pin socket casing (41) on
the adapter cable Ato the radio.
Then lay the adapter cable A with the black 25-pin
connection plug (42), as shown in the figure, above
the steering column to the installation site of the
amplifier and secure it with cable ties.
0
Connect the adapter cable A to the amplifier (1).
Attach the 25-pin connection plug (40) on the
adapter cable A to the plug strip (41) and press it
in the direction indicated by the arrow with a large
flat screwdriver (42) until it audibly engages in the
amplifier casing.
0
Carefully slide the connected, assembled amplifier
(1) behind the cross strut (40) and above the
bottom amplifier holder (5).
As you slide in the amplifier, ensure that you
do not jam or damage any of the cables. The
sequence of the following installation work
must be followed to the letter.
Place a hexagonal screw M8x20 (8) into the pipe
clip (7) and screw on a hexagonal nut with collar
M8 (9).
Do not tighten the nut yet.
B
M
W
41
40
X18126
A
42
046 0641 B
40
41
40
A
42
1
046 0642 B
5
1
40
8
7
9
046 0643 B
EN/13
Retrofit / Installation kit No. 82 83 0 136 518
Installation Instructions No. 01 29 0 136 536 Issue date: 10.2001
5. To install the amplifier and additional wiring harness (for cars with a battery in the boot)
0
0
0
0
0
Secure the bottom amplifier holder (5) to the
amplifier (1) with the two fillister head self-tapping
screws 3.5 x 9.5 (2).
Secure the adapter cable A along the main wiring
harness (40) with cable ties (18).
Align the amplifier (1) and ensure that you do not
jam or damage any of the cables. Then tighten the
securing screw (41) for the control module box and
the hexagonal nut with collar M8 (9).
If the car has an auxiliary heating system,
now reinstall the Telestart receiver you
removed earlier.
0
The figure shows the engine compartment on
the right near the control module box.
Secure the adapter for the earth connection (3) to
the earth post (40) near the brake booster using
the existing hexagonal nut M8.
0
Lay the earth cable (40), brown cable, on the
adapter cable A with the 6 mm cable eyelet
through the opening (41) into the control module
box in the engine compartment on the left.Lay the
power cable (42), red cable on the adapter cable A
along the standard wiring harness to the left door
sill and secure it with cable ties.
0
Carefully cut open the rubber grommet (40) in the
front a little.Carefully push the earth cable (41),
brown cable with 6 mm cable eyelet, through the
opening you have made in the rubber grommet
(40).Then secure the 6 mm cable eyelet (42) to the
adapter for the earth connection (3) using the
hexagonal nut M6 (4).
Seal the rubber grommet (40) around the
opening you cut using sealing compound.
5
1
2
9
A
40
41
18
046 0644 B
3
40
046 0645 B
42
A
40
41
046 0646 B
42
40
3
41
4
046 0647 B
EN/14
Retrofit / Installation kit No. 82 83 0 136 518
Installation Instructions No. 01 29 0 136 536 Issue date: 10.2001
5. To install the amplifier and additional wiring harness (for cars with a battery in the boot)
0
0
0
Lay the power cable (40), red cable on the adapter
cable near the left door sill along the standard
wiring harness under the reinforcement for the rear
seat bench into the boot and secure it with cable
ties.Then lay it along the closing panel to the
installation site of the battery (41) and secure it
with textile adhesive tape (42).
0
The figure shows the boot at the rear right.
Lay the power cable (40), red cable, to the
connection site of the supply cable with fuse B and
cut off the excess length.
Crimp the blade terminal contact (11) on to cut off
power cable (40) and connect it to the supply
cable with fuse B.Secure the cable eyelet, 8 mm in
diameter (41) on the supply cable with fuse B to
the positive pole on the battery.The secure the
supply cable with fuse B and the power cable (41)
with cable ties (18).
046 0652 B
40
18
41
046 0653 B
40
18
18
B
41
11
EN/15
Retrofit / Installation kit No. 82 83 0 136 518
Installation Instructions No. 01 29 0 136 536 Issue date: 10.2001
6. To install the amplifier and additional wiring harness (for cars with a battery in
the engine compartment) with an on-board monitor radio
0
0
0
0
0
Affix the template (26) to the airbag mounting plate
(40) and drill four holes with diameters of 2.5 mm
(41).
0
Affix the template (27) to the airbag mounting plate
(40) and drill two holes with diameters of 2.5 mm
(41).
0
Place the top amplifier holder (6) on the amplifier
(1) and secure it with the two fillister head self-
tapping screws 3.5 x 9.5 (2).
Watch the position of the opening (40) for the
adapter cable connection plug.
0
Secure the amplifier (1) with the top amplifier
holder (6) to the airbag mounting plate (40) with
two fillister head self-tapping screws 3.5 x 9.5 (2).
046 0806 B
40
41
26
40
41
27
046 0807 B
1
2
40
6
046 0808 B
2
1
40
6
046 0809 B
EN/16
Retrofit / Installation kit No. 82 83 0 136 518
Installation Instructions No. 01 29 0 136 536 Issue date: 10.2001
6. To install the amplifier and additional wiring harness
(for cars with a battery in the engine compartment) with an on-board monitor radio
0
0
0
0
0
Mark the holes (41) on the top amplifier holder (6)
from the other side of the airbag mounting plate
(40).
0
Unscrew the amplifier and unscrew the top
amplifier holder.
Drill the marked holes (40) on the top amplifier
holder (6) with a diameter of 2.5 mm.
0
Place the top amplifier holder (6) on the amplifier
(1) and secure it with the two fillister head self-
tapping screws 3.5 x 9.5 (2).
Watch the position of the opening (40) for the
adapter cable connection plug.
0
Secure the amplifier (1) with the top amplifier
holder (6) to the airbag mounting plate (40) with six
fillister head self-tapping screws 3.5 x 9.5 (2).
41
6
40
046 0810 B
40
6
046 0811 B
1
2
40
6
046 0812 B
2
2
6
1
40
046 0813 B
EN/17
Retrofit / Installation kit No. 82 83 0 136 518
Installation Instructions No. 01 29 0 136 536 Issue date: 10.2001
6. To install the amplifier and additional wiring harness
(for cars with a battery in the engine compartment) with an on-board monitor radio
0
0
0
0
0
Cut open the rubber grommet (40) for the airbag
mounting plate.
Push the black 25-pin connection plug on the
radio/amplifier adapter cable A through it.
0
Connect the radio/amplifier adapter cable A to the
amplifier (1).
Attach the 25-pin connection plug (40) on the
adapter cable A to the plug strip (41) and press it
in the direction indicated by the arrow with a large
flat screwdriver (42) until it audibly engages in the
amplifier casing.
0
Place the rubber grommet (40) into the recess in
the airbag mounting plate (41).
0
Secure the rubber engagement pin (40) on the
rubber grommet (41) with cable ties (18).
40
A
046 0814 B
40
41
40
A
42
1
046 0628 B
40
41
046 0416 B
41
40
18
046 0817 B
EN/18
Retrofit / Installation kit No. 82 83 0 136 518
Installation Instructions No. 01 29 0 136 536 Issue date: 10.2001
6. To install the amplifier and additional wiring harness
(for cars with a battery in the engine compartment) with an on-board monitor radio
0
0
0
0
0
Install the airbag mounting plate and amplifier (40)
and lay the radio/amplifier adapter cable A along
the main wiring harness to the on-board monitor
radio.
0
Lay the earth cable (40) and the radio/amplifier
adapter cable along the main wiring harness and
secure them with cable ties (18).
MacPherson strut tower on the left below the
rear seat backrest lock.
0
Secure the earth cable (40) on the radio/amplifier
adapter wiring harness A to the earth post
X13016.
0
Connect the black 17-pin radio connection plug
X18126 to the black 17-pin plug casing (40) on
adapter cable A.
You may have to reconnect the CD changer
connection cable to the black 17-pin socket
casing (41) on the adapter cable A.
Connect the black 17-pin socket casing (41) on
the adapter cable A to the radio.
046 0822 B
40
A
18
046 0823 B
046 0824 B
X13016
40
A
046 0825 B
41
40
X18126
EN/19
Retrofit / Installation kit No. 82 83 0 136 518
Installation Instructions No. 01 29 0 136 536 Issue date: 10.2001
6. To install the amplifier and additional wiring harness
(for cars with a battery in the engine compartment) with an on-board monitor radio
0
0
0
0
0
Lay the 1-pin cable on the radio/amplifier adapter
wiring harness A along the main wiring harness on
the left-hand side.
0
Driver’s footwell.
Lay the 1-pin red cable on the radio/amplifier
adapter wiring harness A, through the opening (40)
into the control module box in the engine
compartment on the left-hand side.
0
Engine compartment at the front left.
Carefully cut open the rubber grommet (40) in the
front.
Lay the 1-pin red cable on the radio/amplifier
adapter wiring harness A, through the opening you
have made in the rubber grommet (40) and then
push it through the rubber grommet (41).
Seal the rubber grommet (40) around the
opening you cut using sealing compound.
0
Lay the 1-pin red cable on the radio/amplifier
adapter wiring harness A, under the cable guide
(40) from the left to the right-hand side of the car.
Then on the right-hand side of the car push it
through the rubber grommet (41) to the installation
site of the battery.
046 0826 B
A
40
A
046 0754 B
A
40
41
046 0726 B
A
A
40
41
A
046 0727 B
EN/20
Retrofit / Installation kit No. 82 83 0 136 518
Installation Instructions No. 01 29 0 136 536 Issue date: 10.2001
6. To install the amplifier and additional wiring harness
(for cars with a battery in the engine compartment) with an on-board monitor radio
0
0
0
0
Cut the 1-pin red cable on the radio/amplifier
adapter wiring harness A, to the appropriate
length, crimp on a blade terminal contact and
insert it into the fuse holder (40).
Secure the cable eyelet (41) on the supply cable
with the fuse B to the positive pole (42).
046 0728 B
40
42
41
B
B
/