Page is loading ...
Sliding Flex Lamp
LTG006
©2023 UPLIFT Desk®. All Rights Reserved
For assembly assistance,
visit upliftdesk.com/contact,
or call 800-349-3839,
or email [email protected]
2
Under no circumstances does the manufacturer accept warranty or liability claims for damages
caused from improper use of this product. Provide this manual to any new user.
Safety and Warnings
CAUTION: Read all instructions before assembly. Failure to assemble or operate properly may result
in damage or personal injury.
CAUTION: If using Lamp on an adjustable height work surface, raise to maximum height before
attaching Lamp to ensure that the power cord will reach the outlet when the worksurface is raised.
CAUTION: Route the power cord so it won’t be stepped on, get pinched, or have items placed on it.
Do not place the Lamp anywhere it could be a tripping hazard.
WARNING: When unplugging, do not pull on power cord or unplug from any angle other than
straight from outlet. Never touch metal conductors on the plug while plugging or unplugging.
WARNING: To avoid electric shock, do not disassemble or tamper with the Lamp or Power Adapter.
Only use the Power Adapter included with this Lamp.
CAUTION: Do not use outdoors. Never use in a wet environment. Never allow liquid of any kind to
spill onto or enter any part of the product. Do not use in high temperatures.
WARNING: Unplug and discontinue use in the event that the following occurs.
• The Power Adapter or cord breaks
• The Lamp’s casing or one or more of the joints break
• The light emits sparks or smoke
• Abnormal ickering occurs or the LED bulb breaks
CAUTION: Do not try to push the joints beyond their adjustment range, as this will cause damage.
Neck Head Power Adapter
M3 x 8mm Flat Head Screw 2mm Allen Wrench
4mm Allen Wrench
Package Contents
3
© UPLIFT Desk • 800-349-3839 • info@upliftdesk.com • upliftdesk.com
Step 1 - Head Attachment
A. Lay the Neck on its back as shown.
B. With the LED strip facing up, slide the Head onto
the end of the Neck until the screw hole in the
Head aligns with the screw hole in the Neck.
Step 2 - Mounting Clamp Adjusting
(if necessary)
The mounting clamp can attach to desktops from 3/4”
to 3 1/2” thick. If the mounting clamp does not t on
your desk edge, you can adjust the clamping range
by removing the lower clamp bracket assembly and
repositioning it by following the steps below.
C. Insert the M3 x 8mm Flat Head Screw
through the hole in the Head and into the
threaded hole in the Neck and tighten it
using the 2mm Allen Wrench.
A. Using the 4mm Allen wrench, remove the two
screws holding the lower clamp bracket assembly
to the back plate of the clamp.
4
B. For thinner desks (minimum 3/4’’), reassemble
the lower clamp bracket assembly in the upper
threaded holes as shown.
C. For thicker desks (maximum 3 1/2”), after removing
the lower clamp bracket assembly, use a Phillips Head
screwdriver to remove the round clamping plate from the
threaded stem and knob. Then remove the threaded stem
and knob from the L-shaped bracket.
D. Flip the L-bracket over.
Round clamping plate
Stem and knob
E. Reinstall the threaded stem and knob though
the bottom of the ipped L-bracket and
reattach the round clamping plate to the
threaded stem.
5
© UPLIFT Desk • 800-349-3839 • info@upliftdesk.com • upliftdesk.com
F. Reattach the lower clamp bracket assembly to the bottom
holes in the back plate as shown using the two screws removed
previously and the 4mm Allen Wrench.
Step 3 - Mount to the Desk
A. Loosen the handle under the mounting clamp at
the base of the Neck and slide the clamp onto the
edge of your desk making sure the back of the
clamp is against the back edge of the desktop.
B. Tighten the knob until the clamp is securely
fastened to the edge of your desk.
6
Step 5 - Lamp Head Positioning
A. The Head of the lamp slides laterally to illuminate
areas as needed. To move the lamp Head, gently
slide it to the left or right to the desired position.
B. The lamp’s exible Neck allows the Head to
be positioned in nearly any orientation. Adjust
the position of the lamp Head by gripping the
Neck, not by gripping the ends of the lamp
Head. Doing so can damage the lamp’s sliding
mechanism.
Note: Positioning the lamp Head vertically with
the Head parallel to the Neck will cause it to
slide down to the end of travel.
Step 4 - Power Cord Connection
A. Plug the barrel end of the Power Adapter cord into the end of the cord
coming from the lamp.
B. Plug the Power Adapter into a 120V power outlet. If you are attaching
the lamp to a height adjustable desk or table, make sure there is
enough slack in the power cord to reach the lamp when the desk or
table is raised.
7
© UPLIFT Desk • 800-349-3839 • info@upliftdesk.com • upliftdesk.com
Step 6 - Lamp Operation
A. Touch the Power button on the front of the lamp Head to turn it on.
B. Touch the Sun button on the front of the lamp Head to cycle through the color temperatures. When turned off, the
Sliding Flex Lamp remembers the color temperature setting for the next session.
2700K 3500K 5000K 5700K
Warm White Natural Cool Cool Daylight
Color temperature settings
C. Touch the Up and Down buttons on the front of the lamp Head to change the brightness of the Sliding Flex Lamp.
When turned off, the lamp remembers the brightness setting for the next session.
Brightness levels:
100% 90% 80% 60% 40% 20%
SAVE THE INSTRUCTIONS
Study this manual carefully. If this product is sold, please provide this
manual to the buyer, installers, or support personnel operating the product.
Work Better. Live Healthier
AI-LTG006-1.0
Copyright Notice: This guide is a component of this UPLIFT Desk product. This guide is a part of
the scope of delivery, even if the item is resold. This guide is also available on the UPLIFT Desk
website: upliftdesk.com. These specications are subject to United States copyright law.
©
upliftdesk.com
800-349-3839
512-614-3152
/
