UPLIFT Desk TOP425 User manual

Brand
UPLIFT Desk
Model
TOP425
Type
User manual

UPLIFT Desk TOP425 is a versatile and sturdy craft table that can be attached to various UPLIFT Desk frames, including 2-leg standing desks, T-frame desks, and seated height tables. It features pre-drilled holes and threaded inserts for easy assembly and comes with #10-24x3/4'' Machine Screws and Washers for attaching the table to the frame. To prevent damage during assembly, place the table upside down on a debris-free carpeted area or blanket and use masking or painter's tape to keep the drawers and lids closed.

UPLIFT Desk TOP425 is a versatile and sturdy craft table that can be attached to various UPLIFT Desk frames, including 2-leg standing desks, T-frame desks, and seated height tables. It features pre-drilled holes and threaded inserts for easy assembly and comes with #10-24x3/4'' Machine Screws and Washers for attaching the table to the frame. To prevent damage during assembly, place the table upside down on a debris-free carpeted area or blanket and use masking or painter's tape to keep the drawers and lids closed.

© UPLIFT Desk • 800-349-3839 • [email protected] • upliftdesk.com
Craft Table
Package Contents
Craft Table
TOP425
Step 1
A. Open your box and dispense of its packaging.
B. Take a moment to put some masking tape on the
drawers and lids so they stay closed while moving,
ipping over, and assembling your desk.
• Note: If you do not use tape, loose drawers and
lids may open suddenly, possibly damaging the
table or causing injury.
These instructions show the Craft Table being attached to an UPLIFT Desk 2-Leg Standing Desk, C-Frame.
The Craft Table can also be used with these UPLIFT Desk frames:
2-Leg Standing Desk, T-Frame 2-Leg Seated Height Table, C-Frame
2-Leg Seated Height Table, T-Frame 4-Leg Standing Height Table
4-Leg Seated Height Table
© UPLIFT Desk • 800-349-3839 • [email protected] • upliftdesk.com
Copyright Notice: These instructions are a component of this product. These instructions are part of the scope of delivery, even if the item is resold. These instructions are also available on the UPLIFT Desk website: uplift-
desk.com. Excerpts or copies may not be forwarded to third parties or used in any other published form without the prior written consent of UPLIFT Desk. These instructions are subject to United States copyright law.
©
AI-TOP425-1.0
CAUTION: Read all instructions before assembly. Failure to assemble properly may result in
damage or personal injury.
WARNING: Exercise caution with the table’s hinged lids as they can slam shut and cause injury.
CAUTIONS & WARNINGS
!
!
!
Step 4
A. Once the Table is secured to the frame, have your
friend help you ip it over safely.
•
Grasp both the frame and Craft Table being
careful to support both equally so you do not
stress the screws or pull them loose and ip the
Table over.
B. Adjust the leveling studs on the feet to ensure that
it is level.
C. Once it is right-side up, carefully remove the tape
from the lids and drawers.
Step 2
A. To avoid any damage to your oor or your Craft
Table, assemble on top of a debris free carpeted
area or blanket.
B. Have a friend help you place the Table upside
down on the blanket or carpet, so that the pre-
drilled holes and threaded inserts are facing up.
Step 3
A. Get ready to attach the desk frame to the Table.
Refer to the instructions provided with your frame
for assembly.
B. Line up the holes in your frame with the threaded
inserts in the table per the frame instructions.
C. Attach the frame to the Table using the #10-
24x3/4’’ Machine Screws and Washers that were
provided with the frame.
NOTE
Masking tape or Painter’s tape should be strong enough to keep drawers and
lids closed while also being gentle enough to not damage your Craft Table’s
surface. Do NOT use other types of tape such as Scotch or Duct tape.
  • Page 1 1
  • Page 2 2

UPLIFT Desk TOP425 User manual

Brand
UPLIFT Desk
Model
TOP425
Type
User manual

UPLIFT Desk TOP425 is a versatile and sturdy craft table that can be attached to various UPLIFT Desk frames, including 2-leg standing desks, T-frame desks, and seated height tables. It features pre-drilled holes and threaded inserts for easy assembly and comes with #10-24x3/4'' Machine Screws and Washers for attaching the table to the frame. To prevent damage during assembly, place the table upside down on a debris-free carpeted area or blanket and use masking or painter's tape to keep the drawers and lids closed.

Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents