FS S5850-24XMG-U User guide

ETHERNET L3 SWITCHES

Ethernet L3-Switches

Switchs Ethernet L3

V1.0

Quick Start Guide

Quick Start Anleitung

Guide de Démarrage Rapide

S5850-24XMG-U

CON

MGMT

1 2 3 4

17 18 19 20 21 22 23 24

9 10 11 12 13 14 15 16

1 2 3 4 5 6 7 8

SYS ID MGMT POE

S5850-24XMG-U POE+

Breakout

26 100G

25

Introduction

EN

Thank you for choosing S5850-24XMG-U Series Switches. This guide is designed to familiarize you

with the layout of the S5850-24XMG-U Series Switches and describes how to deploy them in your

network.

Accessories

S5850-24XMG-U

1

Rubber Pad x4

CON

MGMT

1 2 3 4

17 18 19 20 21 22 23 24

9 10 11 12 13 14 15 161 2 3 4 5 6 7 8

SYS ID MGMT POE

S5850-24XMG-U POE+

Breakout

26 100G

25

Console Cable x1

Front Mounting Bracket x2

Grounding Cable x1Power Cord x1

M4 Screw x12

Rear Mounting Bracket x2Sliding Rail x2

CON

MGMT

1 2 3 4

17 18 19 20 21 22 23 24

9 10 11 12 13 14 15 16

1 2 3 4 5 6 7 8

SYS ID MGMT POE

S5850-24XMG-U POE+

Breakout

26 100G

25

EN

Front Panel Ports

Ports Description

CON

USB

MGMT

POE RJ45

QSFP 28

A RJ45 console port for serial management

A USB management port for software conﬁguration backup and oﬄine

software upgrade

An out-of-band Ethernet management port

RJ45 ports for 10G connection

QSFP 28 ports for 100G connection

LEDs State

SYS

ID

Green

Orange

Blue

OFF

ON

The switch has loaded the agent software code and is

operating normally.

The system operating warning occurred.

The system operating or power supply failure occurred.

ID indication function is active.

ID indication function is not active.

Hardware Overview

S5850-24XMG-U

2

RJ45 QSFP 28

MGMT

CON

MGMT

1 2 3 4

17 18 19 20 21 22 23 24

9 10 11 12 13 14 15 16

1 2 3 4 5 6 7 8

SYS ID MGMT POE

S5850-24XMG-U POE+

Breakout

26 100G

25

RJ45 LED 100G Breakout

100G LED

SYS POE

MGMT

ID

Front Panel LEDs

Description

USB

EN

Back Panel

MGMT

POE

RJ45

100G LED

100G

Breakout

3

4 Hot-swappable Fans 2 Hot-swappable Power Supplies

Grounding Point

LEDs State

Green

OFF

OFF No link.

The port is linked on 100G/25G bandwidth.

The port is linked and there is data activity.

The port is linked on 40G/10G bandwidth.

The port is linked and there is data activity.

The port is linked oﬀ or has been split.

The breakout port is linked oﬀ or has been split.

The breakout port is linked and there is data activity.

The breakout port is linked to 10G/25G.

Link/Act

Green

(left)

Green

Orange

(right)

Yellow (ON)

ON

Green (ON)

Green

(Blinking)

Green

(ON)

Blinking

ON

Blinking

ON

Blinking

ON

Blinking

The port is linked on 100M/1000M.

The port is linked and there is data activity.

The port is linked oﬀ.

The remaining power of the PSE subsystem is less than

the alarm threshold.

The remaining power of the PSE subsystem is greater

than the alarm threshold.

The switch system is not started or the PSE subsystem is

not working properly.

The port is linked and the bandwidth could be 100M/

1G/2.5G/5G/10G.

The port is linked and there is data activity.

Description

EN

Phillips screwdriver.

Standard-sized, 19" wide rack with a minimum of 1U height available.

Category 5e or higher RJ-45 Ethernet cables for connecting network devices.

Installation Requirements

Before installation, make sure that you have the following conditions

ready:

1. Attach four rubber pads to the bottom of switch.

2. Place the switch on a desk.

Mounting the Switch

Site Environment:

Make sure that the temperature of installation site is maintained at 0°~50°.

Make sure that the relative humidity of installation site is maintained at 10%~90%.

The installation site must be free from leaking, dripping water, heavy dew or humidity.

Keep the installation site dust-free.

The installation site must be well ventilated. Ensure that there is adequate air ﬂow around the

switch.

Make sure that the switch is level and stable to avoid any hazardous conditions.

Make sure that the rack and working platforms are well earthed.

Desk Mounting

4

SYS ID MGMT

CON

MGMT

S5850-24XMG

2

1

43

6

58

7

10

9

12

11

14

13 16

15

18

17

20

19

22

21 24

23

123

26 100G

25

4Breakout

CON

MGMT

9 10 11 12

1 2 3 4 5 6 7 8

SYS ID MGMT POE

S5850-24XMG-U POE+

CON

MGMT

9 10 11 12 13 14

1 2 3 4 5 6 7 8

SYS ID MGMT POE

S5850-24XMG-U POE+

POE+

EN

Rack Mounting

1. Secure the mounting brackets to the two sides of the switch with eight M4 screws.

2. Attach the switch to the rack with four M6 screws and cage nuts.

5

1234

17 18 19 20 21 22 23 24

12 13 14 15 16

Breakout

26 100G

25

1234

17 18 19 20 21 22 23 24

15 16

Breakout

26 100G

25

CON

MGMT

9 10 11 12 13 14 15

1 2 3 4 5 6 7 8

SYS ID MGMT POE

S5850-24XMG-U POE+

EN

Rack Mounting-Single Switch Deployment

1. Fix the mounting bracket to the one side of the switch. And ﬁx the rear mounting bracket to the

rack with two M4 screws.

2. Fix the sliding rail to the one side of switch with two M4 screws. And assemble the rear mounting

brackets as the following picture.

3. Front rack installing: Fix the front mounting brackets to the two sides of the switch with eight M4

screws.

4. Fix the switch to the rack with M6 screws and cage nuts.

6

1 2 3 4

17 18 19 20 21 22 23 24

14 15 16

Breakout

26 100G

25

EN

PWR1

1. Take a new power module out of the package and conﬁrm the input mode and the input

parameters of the power module match the requirements.

2. Remove the old power module and take the plane printed with power information as the top panel.

Hold the handle of the power module with one hand, and hold the end with the other hand.

3. Insert it into the power module slot along the guide rail uprightly and slowly until it totally inserts

into place (a “click” sound is heard), then make sure that the module is in good contact with the slot.

EN

Installing the Power Supply Module

7

NOTE: 1. Insert the power module steadily.

2. Pay attention to the direction of insertion.

3. If the position is improper after inserting the power module, press the plug of the power

module and hold on to the handle with one hand to slowly pull it out, then re-insert it.

EN

1. Connect one end of the grounding cable to a proper earth ground, such as the rack in which the

switch is mounted.

2. Secure the grounding lug to the grounding point on the switch back panel with the washers and

screws.

EN

Grounding the Switch

SYS ID MGMT

CON

MGMT

S5850-24XMG

21

43

65 7

8

CAUTION: The earth connection must not be removed unless all supply connections have

been disconnected.

1. Connect one end of an Ethernet cable to the RJ45 port.

2. Connect the other end of the Ethernet cable to another network device.

1. Plug the AC power cord into the power port on the back of the switch.

2. Connect the other end of the power cord to an AC power source.

EN

Connecting the Power

Connecting the RJ45 Ports

8

10

9

12

11

14

13 16

15

18

17

20

19

22

21 24

23

123

26 100G

25

4Breakout

9

Connecting the SFP Ports

WARNING: Do not install power cords while the power is on.

SYS ID MGMT

CON

MGMT

S5850-24XMG

21

43

65 87

10

9

1. Plug the compatible QSFP28 optical module into the QSFP28 port.

2. Connect one end of a ﬁber optic cable to the optical module. Then connect the other end of the

cable to another ﬁber device.

EN

Connecting the QSFP 28 Port

10

Connecting the SFP Ports

WARNING: Laser beams will cause eye damage. Do not look into bores of optical modules

or ﬁber optical cables without eye protection.

10

12

11

14

13 16

15

18

17

20

19

22

21 24

23

123

26 100G

25

4Breakout

CON

MGMT

17 18 19 20 21

910 11 12 13 14 15 16

1 2 3 4 5 6 7 8

SYS ID MGMT POE

S5850-24XMG-U POE+

1. Insert the RJ45 connector of the console cable into the console port of the switch.

2. Connect the DB9 female connector of the console cable to the serial port of the computer.

1. Connect one end of a standard RJ45 Ethernet cable to the MGMT port of the switch.

2. Connect the other end of the cable to a computer.

EN

Connecting the CONSOLE Port

Connecting the MGMT Port

11

Connecting the Management Ports

SYS ID MGMT

CON

MGMT

21

43

65 87

10

9

12

11

14

13 16

15

18

17

20

19

22

21 24

23

POE+

S5850-24XMG-U

1 2 3 4

21 22 23 24

Breakout

26 100G

25

Insert the Universal Serial Bus (USB) ﬂash disk to the USB port for software and conﬁguration backup

and oﬄine software upgrade.

EN

Connecting the USB Port

12

123

26

25

4Breakout

CON

MGMT

17 18 19 20

9 10 11 12 13 14 15 16

1 2 3 4 5 6 7 8

SYS ID MGMT POE

S5850-24XMG-U POE+

USB

EN

13

1 2 3 4

20 21 22 23 24

Breakout

26 100G

25

Conﬁguring the Switch

Conﬁguring the Switch via the Web-based Interface

Step 1: Connect your computer to the Management port of the Switch using the network cable.

Step 2: Set the IP address of the computer to 192.168.1.x ("x" is any number from 2 to 254).

Step 3: Open a browser, type http://192.168.1.1, and enter the default username and password

admin/admin.

?x

OK Cancel

General

IP address:

Subnet mask:

Default gateway:

You can get IP settings assigned automatically if your network

supports this capability. Otherwise, you need to ask your network

administrator for the appropriate IP settings.

Internet Protocol Version 4 (TCP/IPv4) Properties

Use the following IP address:

Obtain an IP address automatically

Preferred DNS server:

Alternate DNS server:

Validate settings upon exit Advanced...

. . . 21168192

0255

255255

. . .

Obtain DNS server address automatically

Use the following DNS server addresses:

IE 8/9/10/11, Google Chrome, Firefox are supported

Login

admin

*****

Step 4: Click Login to display the web-based conﬁguration page.

EN

14

Conﬁguring the Switch via the Console Port

Step 1: Connect a computer to the switch's console port using the console cable.

Step 2: Start the terminal simulation software such as HyperTerminal on the computer.

Step 3: Set the parameters of the HyperTerminal: 9600 bits per second, 8 data bits, no parity, 1 stop bit

and no ﬂow control.

Step 4: After setting the parameters, click Connect to enter.

x

Quick Connect

Protocol:

The port may be manually entered or selected from the list.

Serial

Flow Control

DTR/DSR

RTS/CTS

XON/XOFF

Save sessionShow quick connect on startup

Open in a tab

Connect Cancel

COM3

115200

8

None

1

Port:

Baud rate:

Data bits:

Parity:

Stop bits:

Name of pipe:

EN

15

Troubleshooting

The Power Module Cannot Supply Power

All LEDs on the front panel, the fan module and the panel of the power module are oﬀ. The fan does

not work. First disconnect the power cord of the power module, then check the following:

1. Check whether the cable connections of the rack are correct.

2. Check whether the connection between the power socket and the power cord is loose.

3. Check whether the connection between the power module and the power cord is loose.

4. Check whether the power module inserts into place.

1. Test network connectivity through ping.

2. If the network is reachable, try restarting the switch.

3. Check whether the corresponding service enables.

1. Check whether the console cable is correctly connected.

2. Check whether the console cable is broken.

3. Check whether the console port of the switch is the same as the port of the terminal device.

4. Check whether the console port conﬁguration of the terminal device is correct.

Connecting the Switch Remotely Unsuccessfully

1. Check whether the receiving and delivering of ﬁber optical cable connects correctly.

2. Check whether the wavelengths of optical modules of the interconnection are the same.

3. Check whether the distance of the interconnection is within the distance marked by the optical

module.

4. Check whether the rates of the interconnection are the same or whether the mode of port rate is

conﬁgured correctly for ports which support diﬀerent rates.

5. Check whether the optical ﬁber type meets the requirements.

The Optical Port Cannot Link up

No Characters/Distorted Characters are Displayed on the Screen of the

Terminal Device

EN

FS ensures our customers that any damage or faulty items due to our workmanship, we will oﬀer a

free return within 30 Days from the day you receive your goods. This excludes any custom-made

items or tailored solutions.

Return: If you want to return item(s), information on how to return can be found at

https://www.fs.com/policies/day_return_policy.html

Warranty: S5850-24XMG-U Series enjoy a 5-year limited warranty against defect in

materials or workmanship. For more details about warranty, please check at

https://www.fs.com/policies/warranty.html

5

Product Warranty

16

Online Resources

Download

Help Center

Contact Us

https://www.fs.com/products_support.html

https://www.fs.com/service/fs_support.html

https://www.fs.com/contact_us.html

DE

17

Einführung

Vielen Dank, dass Sie sich für Switches der Serie S5850-24XMG-U entschieden haben. Diese Anleitung

soll Sie mit dem Layout der S5850-24XMG-U Serie Switches vertraut machen und beschreibt, wie Sie

diese in Ihrem Netzwerk einsetzen können.

Zubehör

S5850-24XMG-U

Gummipad x4

CON

MGMT

1 2 3 4

17 18 19 20 21 22 23 249 10 11 12 13 14 15 16

1 2 3 4 5 6 7 8

SYS ID MGMT POE

S5850-24XMG-U POE+

Breakout

26 100G

25

Konsolenkabel x1

Vordere

Montagehalterung x2

Erdungskabel x1Netzkabel x1

M4-Schraube x12

Hintere

Montagehalterung x2

Schiebeschiene x2

DE

18

CON

MGMT

1 2 3 4

17 18 19 20 21 22 23 24

9 10 11 12 13 14 15 16

1 2 3 4 5 6 7 8

SYS ID MGMT POE

S5850-24XMG-U POE+

Breakout

26 100G

25

Ports an der Vorderseite

Port Beschreibung

CON

USB

MGMT

POE RJ45

QSFP 28

Ein RJ45-Console-Port für die serielle Verwaltung

Ein USB-Verwaltungsport für die Sicherung der Softwarekonﬁguration und

die Oﬄine-Aktualisierung der Software

Ein Out-of-Band-Ethernet-Management-Port

RJ45-Ports für 10G-Verbindung

QSFP28 Ports für 100G-Verbindung

LED Status

SYS

ID

Grün

Orange

Blau

AUS

AN

Der Switch hat den Softwarecode des Agenten geladen und

arbeitet normal.

Die Systembetriebswarnung wird angezeigt.

Das Betriebssystem oder die Stromversorgung ist ausgefallen.

Die ID-Anzeigefunktion ist aktiv.

Die ID-Anzeigefunktion ist nicht aktiv.

Hardware-Übersicht

S5850-24XMG-U

RJ45 QSFP 28

MGMT

CON

MGMT

1 2 3 4

17 18 19 20 21 22 23 24

9 10 11 12 13 14 15 16

1 2 3 4 5 6 7 8

SYS ID MGMT POE

S5850-24XMG-U POE+

Breakout

26 100G

25

RJ45 LED 100G Breakout

100G LED

SYS POE

MGMT

ID

LEDs an der Vorderseite

Beschreibung

USB

DE

19

Rückseite

4 Hot-swap-fähige Lüfter 2 Hot-swap-fähige Netzteile

Erdungspunkt

MGMT

POE

RJ45

100G LED

100G

Breakout

LED Status

Grün

AUS

AUS Kein Verbindung.

Der Port ist mit einer 100G/25G-Bandbreite verbunden.

Der Port ist verbunden und es gibt Datenaktivität.

Der Port ist mit einer Bandbreite von 40G/10G verbunden.

Der Port ist verbunden und es gibt Datenaktivität.

Der Anschluss ist nicht verbunden oder wurde geteilt.

Der Breakout-Port ist nicht angeschlossen oder wurde geteilt.

Der Breakout-Port ist verbunden und es gibt Datenaktivität.

Der Breakout-Port ist mit 10G/25G verbunden.

Link/Act

Grün

(links)

Grün

Orange

(rechts)

Gelb (AN)

AN

Grün (AN)

Grün

(Blinkt)

Grün

(AN)

Blinkt

AN

Blinkt

AN

Blinkt

AN

Blinkt

Der Port ist mit 100M/1000M verbunden.

Der Port ist verbunden und es gibt Datenaktivität.

Der Port ist nicht verbunden.

Die verbleibende Leistung des PSE-Teilsystems liegt

unter der Alarmschwelle.

Die verbleibende Leistung des PSE-Teilsystems ist

größer als die Alarmschwelle.

Das Switch-System ist nicht eingeschaltet oder das

PSE-Subsystem arbeitet nicht ordnungsgemäß.

The port is linked and the bandwidth could be 100M/

1G/2.5G/5G/10G.

Der Port ist verbunden und die Bandbreite kann

100M/1G/2,5G/5G/10G betragen.

Beschreibung

Page is loading ...

FS S5850-24XMG-U User guide

FS S5850-24XMG-U User guide

in other languages

Related papers

Other documents