ASRock Rack SPC741D8QM3-2T/X550 User manual

SPC741D8QM3-2T/X550

User Manual

Version 1.0

Published March 2023

Version 1.0

Published March 2023

Copyright Notice:

No part of this documentation may be reproduced, transcribed, transmitted, or translated

in any language, in any form or by any means, except duplication of documentation by the

purchaser for backup purpose, without written consent of ASRock Rack Inc.

Products and corporate names appearing in this documentation may or may not be

registered trademarks or copyrights of their respective companies, and are used only for

identication or explanation and to the owners’ benet, without intent to infringe.

Disclaimer:

Specifications and information contained in this documentation are furnished for

informational use only and subject to change wit hout notice, and should not be

constructed as a commitment by ASRock Rack. ASRock Rack assumes no responsibility

for any errors or omissions that may appear in this documentation.

With respect to the contents of this documentation, ASRock Rack does not provide

warranty of any kind, either expressed or implied, including but not limited to the implied

warranties or conditions of merchantability or tness for a particular purpose.

In no event shall ASRock Rack, its directors, ocers, employees, or agents be liable for

any indirect, special, incidental, or consequential damages (including damages for loss of

prots, loss of business, loss of data, interruption of business and the like), even if ASRock

Rack has been advised of the possibility of such damages arising from any defect or error

in the documentation or product.

is device complies with Part 15 of the FCC Rules. Operation is subject to the following

two conditions:

(1) this device may not cause harmful interference, and

(2) this device must accept any interference received, including interference that

may cause undesired operation.

is equipment has been tested and found to comply with the limits for a Class B digital

device, pursuant to part 15 of the FCC Rules. ese limits are designed to provide reason-

able protection against harmful interference in a residential installation. is equipment

generates, uses and can radiate radio frequency energy and, if not installed and used in ac-

cordance with the instructions, may cause harmful interference to radio communications.

However, there is no guarantee that interference will not occur in a particular installation.

If this equipment does cause harmful interference to radio or television reception, which

can be determined by turning the equipment o and on, the user is encouraged to try to

correct the interference by one or more of the following

measures:

- Reorient or relocate the receiving antenna.

- Increase the separation between the equipment and receiver.

- Connect the equipment into an outlet on a circuit dierent from that to which the

receiver is connected.

- Consult the dealer or an experienced radio/TV technician for help.

INTEL END USER SOFTWARE LICENSE AGREEMENT

IMPORTANT - READ BEFORE COPYING, INSTALLING OR USING.

LICENSE. Licensee has a license under Intel’s copyrights to reproduce Intel’s Software

only in its unmodified and binary form, (with the accompanying documentation, the

“Soware”) for Licensee’s personal use only, and not commercial use, in connection with

Intel-based products for which the Soware has been provided, subject to the following

conditions:

(a) Licensee may not disclose, distribute or transfer any part of the Soware, and You agree

to prevent unauthorized copying of the Soware.

(b) Licensee may not reverse engineer, decompile, or disassemble the Soware.

(c) Licensee may not sublicense the Soware.

(d) e Soware may contain the soware and other intellectual property of third party

suppliers, some of which may be identied in, and licensed in accordance with, an enclosed

license.txt le or other text or le.

(e) Intel has no obligation to provide any support, technical assistance or updates for the

Soware.

OWNERSHIP OF SOFTWARE AND COPYRIGHTS. Title to all copies of the Soware

remains with Intel or its licensors or suppliers. e Soware is copyrighted and protected

by the laws of the United States and other countries, and international treaty provisions.

Licensee may not remove any copyright notices from the Soware. Except as otherwise ex-

pressly provided above, Intel grants no express or implied right under Intel patents, copy-

rights, trademarks, or other intellectual property rights. Transfer of the license terminates

Licensee’s right to use the Soware.

DISCLAIMER OF WARRANTY. e Soware is provided “AS IS” without warranty of

any kind, EITHER EXPRESS OR IMPLIED, INCLUDING WITHOUT LIMITATION,

WARRANTIES OF MERCHANTABILITY OR FITNESS FOR ANY PARTICULAR PUR-

POSE.

LIMITATION OF LIABILITY. NEITHER INTEL NOR ITS LICENSORS OR SUPPLIERS

WILL BE LIABLE FOR ANY LOSS OF PROFITS, LOSS OF USE, INTERRUPTION OF

BUSINESS, OR INDIRECT, SPECIAL, INCIDENTAL, OR CONSEQUENTIAL DAMAG-

ES OF ANY KIND WHETHER UNDER THIS AGREEMENT OR OTHERWISE, EVEN

IF INTEL HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES.

LICENSE TO USE COMMENTS AND SUGGESTIONS. is Agreement does NOT ob-

ligate Licensee to provide Intel with comments or suggestions regarding the Software.

However, if Licensee provides Intel with comments or suggestions for the modication,

correction, improvement or enhancement of (a) the Soware or (b) Intel products or pro-

cesses that work with the Soware, Licensee grants to Intel a non-exclusive, worldwide,

perpetual, irrevocable, transferable, royalty-free license, with the right to sublicense, under

Licensee’s intellectual property rights, to incorporate or otherwise utilize those comments

and suggestions.

TERMINATION OF THIS LICENSE. Intel or the sublicensor may terminate this license

at any time if Licensee is in breach of any of its terms or conditions. Upon termination,

Licensee will immediately destroy or return to Intel all copies of the Soware.

THIRD PARTY BENEFICIARY. Intel is an intended beneciary of the End User License

Agreement and has the right to enforce all of its terms.

U.S. GOVERNMENT RESTRICTED RIGHTS. The Software is a commercial item (as

dened in 48 C.F.R. 2.101) consisting of commercial computer soware and commercial

computer soware documentation (as those terms are used in 48 C.F.R. 12.212), consistent

with 48 C.F.R. 12.212 and 48 C.F.R 227.7202-1 through 227.7202-4. You will not provide

the Soware to the U.S. Government. Contractor or Manufacturer is Intel Corporation,

2200 Mission College Blvd., Santa Clara, CA 95054.

EXPORT LAWS. Licensee agrees that neither Licensee nor Licensee’s subsidiaries will

export/re-export the Software, directly or indirectly, to any country for which the U.S.

Department of Commerce or any other agency or department of the U.S. Government or

the foreign government from where it is shipping requires an export license, or other gov-

ernmental approval, without rst obtaining any such required license or approval. In the

event the Soware is exported from the U.S.A. or re-exported from a foreign destination

by Licensee, Licensee will ensure that the distribution and export/re-export or import of

the Soware complies with all laws, regulations, orders, or other restrictions of the U.S.

Export Administration Regulations and the appropriate foreign government.

APPLICABLE LAWS. is Agreement and any dispute arising out of or relating to it will

be governed by the laws of the U.S.A. and Delaware, without regard to conflict of laws

principles. e Parties to this Agreement exclude the application of the United Nations

Convention on Contracts for the International Sale of Goods (1980). e state and federal

courts sitting in Delaware, U.S.A. will have exclusive jurisdiction over any dispute arising

out of or relating to this Agreement. e Parties consent to personal jurisdiction and venue

in those courts. A Party that obtains a judgment against the other Party in the courts iden-

tied in this section may enforce that judgment in any court that has jurisdiction over the

Parties.

Licensee’s specic rights may vary from country to country.

CALIFORNIA, USA ONLY

e Lithium battery adopted on this motherboard contains Perchlorate, a toxic substance

controlled in Perchlorate Best Management Practices (BMP) regulations passed by the

California Legislature. When you discard the Lithium battery in California, USA, please

follow the related regulations in advance.

“Perchlorate Material-special handling may apply, see www.dtsc.ca.gov/hazardouswaste/

perchlorate”

AUSTRALIA ONLY

Our goods come with guarantees that cannot be excluded under the Australian Consumer

Law. You are entitled to a replacement or refund for a major failure and compensation for

any other reasonably foreseeable loss or damage caused by our goods. You are also entitled

to have the goods repaired or replaced if the goods fail to be of acceptable quality and the

failure does not amount to a major failure. If you require assistance please call ASRock

Rack Tel : +886-2-55599600 ext.123 (Standard International call charges apply)

ASRock Rack INC. hereby declares that this device is in compliance with the essential re-

quirements and other relevant provisions of related UKCA Directives. Full text of UKCA

declaration of conformity is available at: http://www.asrockrack.com

ASRock Rack INC. hereby declares that this device is in compliance with the essential re-

quirements and other relevant provisions of related Directives. Full text of EU declaration

of conformity is available at: http://www.asrockrack.com

ASRock Rack follows the green design concept to design and manufacture our products,

and makes sure that each stage of the product life cycle of ASRock Rack product is in line

with global environmental regulations. In addition, ASRock Rack disclose the relevant in-

formation based on regulation requirements.

Please refer to https://www.asrockrack.com/general/about.asp?cat=Responsibility for in-

formation disclosure based on regulation requirements ASRock Rack is complied with:

DO NOT throw the motherboard in municipal waste. is product has been

designed to enable proper reuse of parts and recycling. This symbol of the

crossed out wheeled bin indicates that the product (electrical and electronic

equipment) should not be placed in municipal waste. Check local regulations

for disposal of electronic products.

Contents

Chapter 1 Introduction 1

1.1 Package Contents 1

1.2 Specications 2

1.3 Unique Features 5

1.4 Motherboard Layout 6

1.5 Onboard LED Indicators 9

1.6 I/O Panel 11

1.7 Block Diagram 13

Chapter 2 Installation 14

2.1 Screw Holes 14

2.2 Pre-installation Precautions 14

2.3 Installing the CPU and Heatsink 15

2.4 Installation of Memory Modules (DIMM) 21

2.5 Expansion Slots (PCI Express Slots) 23

2.6 Jumper Setup 24

2.7 Onboard Headers and Connectors 26

2.8 ATX PSU Power Connections 33

2.9 Dr. Debug 34

2.10 Unit Identication purpose LED/Switch 40

2.11 Dua LAN and Teaming Operation Guide 41

2.12 M.2 SSD Module Installation Guide 42

Chapter 3 UEFI Setup Utility 44

3.1 Introduction 44

3.1.1 UEFI Menu Bar 44

3.1.2 Navigation Keys 45

3.2 Main Screen 46

3.2.1 Motherboard Information 47

3.2.2 Processor Information 47

3.2.3 Memory Information 48

3.3 Advanced Screen 49

3.3.1 CPU Conguration 50

3.3.2 Platform Power Conguration 52

3.3.3 DRAM Conguration 55

3.3.4 Chipset Conguration 57

3.3.5 Storage Conguration 60

3.3.6 NVMe Conguration 3.3 NVMe Conguration 61

3.3.7 ACPI Conguration 62

3.3.8 USB Conguration 63

3.3.9 Super IO Conguration 64

3.3.10 Serial Port Console Redirection 65

3.3.11 H/W Monitor 68

3.3.12 Runtime Error Logging 69

3.3.13 Intel SPS Conguration 71

3.3.14 Network Stack Conguration 72

3.3.15 Intel® VMD technology 73

3.3.16 Driver Health 74

3.3.17 Tls Auth Conguration 75

3.3.18 Instant Flash 76

3.4 Server Mgmt 77

3.4.1 BMC Network Conguration 79

3.4.2 System Event Log 81

3.4.3 BMC Tools 82

3.5 Security 83

3.5.1 Key Management 84

3.6 Event Logs 88

3.7 Boot Screen 89

3.8 Exit Screen 90

Chapter 4 Software Support 91

4.1 Download and Install Operating System 91

4.2 Download and Install Software Drivers 91

4.3 Contact Information 91

Chapter 5 Troubleshooting 92

5.1 Troubleshooting Procedures 92

5.2 Technical Support Procedures 94

5.3 Returning Merchandise for Service 94

SPC741D8QM3-2T/X550

PB 1

English

Chapter 1 Introduction

ank you f or p urchasing A SRock R ack SPC741D8QM3-2T/X550 motherboard, a reliable

motherboard produced under ASRock Rack’s consistently stringent quality control. It delivers

excellent performance with robust design conforming to ASRock Rack’s commitment to

quality and endurance.

In this manual, chapter 1 and 2 contains introduction of the motherboard and step-by-step

guide to the hardware installation. Chapter 3 and 4 contains the configuration guide to

BIOS setup and information of the software support.

1.1 Package Contents

•ASRock Rack SPC741D8QM3-2T/X550 Motherboard

(CEB Form Factor: 12-in x 10.5-in)

•Quick Installation Guide

•1 x SATA3 Cable (60cm)

•1 x Oculink to 4 SATA Cable (60cm)

•1 x I/O Shield

•2 x Screws for M.2 Sockets

•2 x CPU Non-Fabric Carriers

If any items are missing or appear damaged, contact your authorized dealer.

Because the motherboard specications and the BIOS soware might be updated, the con-

tent of this manual will be subject to change without notice. In case any modications of

this manual occur, the updated version will be available on ASRock Rack website without

further notice. You may nd the latest memory and CPU support lists on ASRock Rack

website as well. ASRock Rack’s Website: www.ASRockRack.com

If you require technical support related to this motherboard, please visit our website for

specic information about the model you are using.

http://www.asrockrack.com/support/

2 3

English

1.2 Specications

SPC741D8QM3-2T/X550

Physical Status

Form Factor CEB

Dimension 12” x 10.5” (304.8 x 266.7 mm)

Processor System

CPU Supports 4th Gen Intel® Xeon® Scalable Processors

Socket Single Socket E (LGA 4677)

ermal Design

Power (TDP)

~350W

Chipset Intel® C741

System Memory

Supported DIMM

Quantity

8 DIMM slots (1DPC)

Supported Type 288-pin DDR5 RDIMM/RDIMM-3DS

Max. Capacity per

DIMM

RDIMM:64GB

RDIMM-3DS: 256GB

Max. Frequency 4800 MT/s

Voltage 1.1V

Note Memory support is to be validated

PCIe Expansion Slots (SLOT7 close to CPU)

SLOT6 PCIe5.0 / CXL1.1 x16 [CPU]

SLOT1 PCIe4.0 x16 [CPU]

Other PCIe Expansion Connectors

M.2 slot 1 M-key M2_1 (PCIe3.0 x4 or SATA 6Gb/s), supports 2280/2260

form factor [PCH]

1 M-key M2_2 (PCIe3.0 x4 or SATA 6Gb/s), supports

22110/2280 form factor [PCH]

OCuLink 1 OCuLink (PCIe3.0 x4 or 4 SATA 6Gb/s) [PCH]

MCIO 4 MCIO (PCIE5.0 x8) [CPU]

SATA/SAS Storage

PCH Built-in

Storage

Intel® C741 (Up to 8 SATA 6Gb/s, support RAID 0/1/5/10):

1 OCuLink, 2 SATA 7-pin, 2 M.2

Ethernet

OCP slot 1 OCP NIC 3.0 (PCIe5.0 / CXL1.1 x16) [CPU]

USB

Controller/Hub ASMedia ASM1074

Connectors/

headers

External:

2 Type A (USB3.2 Gen1)

Internal:

1 header (19-pin, 2 USB3.2 Gen1)

1 header (9-pin, 2 USB2.0)

SPC741D8QM3-2T/X550

2 3

English

Graphics

Controller ASPEED AST2600:

1 DB15 (VGA), 1 header

Security

TPM 1 (13-pin, SPI)

Rear I/O

UID button/LED 1 UID button w/ LED

Video output 1 DB15 (VGA)

Serial port 1 DB9 (COM)

USB 2 Type A (USB3.2 Gen1)

RJ45 2 RJ45 (10GbE), 1 dedicated IPMI

Hardware Monitor

Temperature CPU, PCH, MB, Card Side, M.2, RAM, TR1 Temperature

Sensing

Fan Fan Tachometer

CPU Quiet Fan (Allow Chassis Fan Speed Auto-Adjust by

CPU Temperature)

Fan Multi-Speed Control

Voltage 1.05V_PCH, 1.8V_PCH, +BAT, PVNN_PCH, 3.3V, 5V, 12V,

3.3VSB, 5VSB, 12V, +12VSB

Server Management

BMC Controller ASPEED AST2600: IPMI2.0 with iKVM and vMedia support

IPMI Dedicated

GLAN

1 RJ45 Dedicated IPMI LAN port by Realtek RTL8211F

System BIOS

BIOS type AMI UEFI BIOS; 512Mb SPI Flash ROM

Features Plug and Play (PnP), ACPI 4.0 and above compliance wake up

events, SMBIOS 3.4 and above , ASRock Rack Instant Flash

Internal Connectors/Headers

PSU connector 1 Micro-Fit (4-pin, ATX PSU signal) w/ ATX 24-pin adapter

cable, 3 (8-pin, ATX 12V)

Auxiliary panel

header

1 (18-pin): chassis intrusion, system fault LED, LAN1/LAN2

activity LED, locate, SMBus

System panel

header

1 (9-pin): power switch, reset switch, system power LED, HDD

activity LED

NMI button/

header

1

VGA header 1 (15-pin)

Speaker header 1 (4-pin)

Fan header 8 (6-pin)

ermal sensor

header

1

TPM header 1 (13-pin, SPI)

VROC header 1

4 5

English

SGPIO header 2

HSBP 1

SMbus header 1

PMbus header 1

IPMB header 1

Clear CMOS 1 (contact pads)

LED Indicators

Standby Power

LED

1

80 debug port LED 1

Fan Fail LED 8

BMC Heartbeat

LED

1

Supported OS

OS Microso® Windows®

- Server 2022 (64bit)

Linux®

- RedHat Enterprise Linux Server 8.4 (64bit) / 8.5 (64bit) / 8.6

(64bit) / 8.7 (64bit) / 9.0 (64bit) / 9.1 (64bit)

- SUSE Enterprise Linux Server 15 SP3 (64bit) / 15 SP4 (64bit)

- Ubuntu 21.10 (64bit) / 22.04 (64bit) / 22.10 (64bit)

Hypervisor

- VMWare® ESXi 7.0 U3g / 8.0

*Please refer to our website for the latest OS support list.

Enviroment

Operating

temperature

10 - 35°C (50 - 95 degF)

Non-operating

temperature

-40 - 70°C (-40 - 158degF)

NOTE: Please refer to our website for the latest specications.

If you install Intel® LAN utility or Marvell SATA utility, this motherboard may fail Win-

dows® Hardware Quality Lab (WHQL) certication tests. If you install the drivers only, it

will pass the WHQL tests.

is motherboard supports Wake from on Board LAN. To use this function, please make

sure that the “Wake on Magic Packet from power o state” is enabled in Device Manager

> Intel® Ethernet Connection > Power Management. And the “PCI Devices Power On” is

enabled in UEFI SETUP UTILITY > Advanced > ACPI Conguration. Aer that, onboard

LAN1&2 can wake up S5 under OS.

SPC741D8QM3-2T/X550

4 5

English

1.3 Unique Features

ASRock Rack Instant Flash is a BIOS ash utility embedded in Flash ROM. is convenient

BIOS update tool allows you to update system BIOS without entering operating systems rst

like MS-DOS or Windows®. With this utility, you can press the <F6> key during the POST or

the <F2> key to enter into the BIOS setup menu to access ASRock Rack Instant Flash. Just

launch this tool and save the new BIOS le to your USB ash drive, oppy disk or hard drive,

then you can update your BIOS only in a few clicks without preparing an additional oppy

diskette or other complicated ash utility. Please be noted that the USB ash drive or hard

drive must use FAT32/16/12 le system.

6 7

English

1.4 Motherboard Layout

SPC741D8QM3-2T/X550

26.7 cm (10.5 in)

30.5 cm (12 in)

8.1cm (3.2in)

UID1

T:USB3_2

B:USB3_1

CPU1_HSBP1

IPMI_LAN

USB 3.2

Gen1 Ports

LAN1

LAN2

VGA_COM1

ASPEED

AST2600

CPU0

BMC

ROM

PECI1

BMC_SMB1

IPMB1 FLASH_SEC_OVERRIDE1

BIOS

ROM

TPM_BIOS_PH1

RAID_1

AUX_PANEL1

SPEAKER1

TR1

PANEL1

SATA_0_1

BAT1

FAN7

FAN8

FAN3

FAN4

FAN5

FAN6

ATX12V1

ATX12V2

ATX12V3

MCIO1

MCIO2

PSU_SMB1

ATX4PIN1

PWM_CFG1

FRNT_VGA1

MCIO3

MCIO4

DDR5_D1

DDR5_C1

DDR5_B1

DDR5_A1

DDR5_E1

DDR5_F1

DDR5_G1

DDR5_H1

FAN1

FAN2

OCU1

MIPI1

M2_1

M2_2

BMC_PH1

USB3_3_4

BIOS_PH1

SATA0_SGPIOSATA1_SGPIO

USB_1_2NMI_BTN1

+12VSB_SEL1

PASSWORD_CLEAR1

ME_RECOVERY1

OCUSW_1

BIOS_SWAP_OVERRIDE1

PCIE1

PCIE6

OCP1

CLRMOS1

Intel

X550-AT2

SUPER

I/O

Dr. Debug

NUT80_2

NUT110_1

1

8

9

7

11

12

19

15

16

13

14

17

18

20

21

2 3 4

10

23

24

25

26

27

29

3132

37

38

39

56

22

28

30

33

34

35

36

4041

42

4344

45

46

47

48

49

50

52

51

53

SPC741D8QM3-2T/X550

6 7

English

No. Description

1 Backplane PCI Express Hot-Plug Connector (CPU1_HSBP1)

2 Front VGA Header (FRNT_VGA1)

3 Mini Cool Edge IO x8 Connector (MCIO3)

4 Mini Cool Edge IO x8 Connector (MCIO4)

5 2 x 288-pin DDR5 DIMM Slots (DDR5_B1, DDR5_D1)*

6 2 x 288-pin DDR5 DIMM Slots (DDR5_A1, DDR5_C1)*

7 System Fan Connector (FAN1)

8 Mini Cool Edge IO x8 Connector (MCIO1)

9 Mini Cool Edge IO x8 Connector (MCIO2)

10 System Fan Connector (FAN2)

11 PWM Conguration Header (PWM_CFG1)

12 Micro-Fit ATX 4Pin Power Connector (ATX4PIN1)

13 ATX 12V Power Connector (ATX12V1)

14 2 x 288-pin DDR5 DIMM Slots (DDR5_E1, DDR5_G1)*

15 2 x 288-pin DDR5 DIMM Slots (DDR5_F1, DDR5_H1)*

16 ATX 12V Power Connector (ATX12V2)

17 PSU SMBus Header (PSU_SMB1)

18 ATX 12V Power Connector (ATX12V3)

19 OCuLink Connector (OCU1)

20 System Fan Connector (FAN3)

21 System Fan Connector (FAN4)

22 M-key M.2 Socket (M2_2) (Type 22110/2280)

23 System Fan Connector (FAN5)

24 System Fan Connector (FAN6)

25 Serial ATA3 Connectors (SATA_1)(Upper), (SATA_0)(Lower)

26 USB 3.2 Gen1 Header (USB3_3_4)

27 System Fan Connector (FAN7)

28 Clear CMOS Pad (CLRMOS1)

29 System Fan Connector (FAN8)

30 SATA SGPIO Connector (SATA0_SGPIO)

31 Virtual RAID On CPU Header (RAID_1)

32 Flash Override Jumper (FLASH_SEC_OVERRIDE1)

33 System Panel Header (PANEL1)

34 SATA SGPIO Connector (SATA1_SGPIO)

8 9

English

No. Description

35 Auxiliary Panel Header (AUX_PANEL1)

36 Speaker Header (SPEAKER1)

37 USB 2.0 Header (USB_1_2)

38 Non Maskable Interrupt Button (NMI_BTN1)

39 OCP3 +12VSB Power Jumper (+12VSB_SEL1)

40 ermal Sensor Header (TR1)

41 SPI TPM Header (TPM_BIOS_PH1)

42 BIOS Swap Override Jumper (BIOS_SWAP_OVERRIDE1)

43 ME Recovery Jumper (ME_RECOVERY1)

44 Switch SATA and PCIE Jumper (OCUSW_1)

45 BMC SMBus Header (BMC_SMB1)

46 Intelligent Platform Management Bus Header (IPMB1)

47 Password Reset Jumper (PASSWORD_CLEAR1)

48 PCI Express 4.0 x16 Slot (PCIE1)

49 OCP 3.0 Gen5 x16 NIC Slot (OCP1)

50 M-key M.2 Socket (M2_1) (Type 2280/2260)

51 PCI Express 5.0 x16 Slot (PCIE6)

52 CPU PECI Mode Jumper (PECI1)

53 LGA 4677 CPU Socket (CPU0)

*For DIMM installation and conguration instructions, please see p.21 (Installation of Memory Modules

(DIMM)) for more details.

SPC741D8QM3-2T/X550

8 9

English

1.5 Onboard LED Indicators

1

2

3

4

5

6

7

8

9

10

11

10 11

English

No. Item Status Description

1LED_FAN1 Red FAN1 failed

2LED_FAN2 Red FAN2 failed

3LED_CATERR1 Red CPU CATERR error

4BMC_LED Green BMC heartbeat LED

5LED_FAN3 Red FAN3 failed

6LED_FAN4 Red FAN4 failed

7LED_FAN5 Red FAN5 failed

8LED_FAN6 Red FAN6 failed

9LED_FAN7 Red FAN7 failed

10 LED_FAN8 Red FAN8 failed

11 SB_PWR1 Green STB PWR ready

SPC741D8QM3-2T/X550

10 11

English

1.6 I/O Panel

621 4

3 5

7

No. Description No. Description

1 UID Switch (UID1) 5 LAN RJ-45 Port (IPMI_LAN)*

2VGA Port (VGA) 6 10G LAN RJ-45 Port (LAN2)**

3 Serial Port (COM1) 7 10G LAN RJ-45 Port (LAN1)**

4 USB 3.2 Gen1 Ports (USB3_1_2)

LAN Port LED Indications

*ere are two LEDs on each LAN port. Please refer to the table below for the LAN port

LED indications.

Dedicated IPMI LAN Port LED Indications

Activity / Link LED Speed LED

Status Description Status Description

O No Link O 10Mbps connection or

no link

Blinking Yellow Data Activity Orange 100Mbps connection

On Link Green 1Gbps connection

ACT/LINK LED

SPEED LED

LAN Port

12 13

English

**ere are two LEDs on each LAN port. Please refer to the table below for the LAN port

LED indications.

10G LAN Port LED Indications

Activity / Link LED Speed LED

Status Description Status Description

O No Link O 100Mbps connection or no

link

Blinking Green Data Activity Orange 1Gbps connection

On Link Green 10Gbps connection

ACT/LINK LED

SPEED LED

LAN Port

Page is loading ...

ASRock Rack SPC741D8QM3-2T/X550 User manual

ASRock Rack SPC741D8QM3-2T/X550 User manual

Related papers

Other documents