THORLABS TLV-U-FF User manual

Brand
THORLABS
Model
TLV-U-FF
Type
User manual
TLV-U-FF
Filter Cube Assembly for Olympus
BX3 and IX3 Microscopes
User Guide
Filter Cube Assembly
Table of Contents
Chapter 1Safety ................................................................................. 1
Chapter 2Assembly Instructions ..................................................... 2
2.1.Step1............................................................................2
2.2.Step2............................................................................2
2.3.Step3............................................................................3
2.4.Step4............................................................................4
2.5.Step5............................................................................4
2.6.Step6............................................................................5
Chapter 3Regulatory ......................................................................... 7
Chapter 4Thorlabs Worldwide Contacts......................................... 8
Filter Cube Assembly Chapter 1: Safety
Rev A, November 7, 2016 Page 1
Chapter 1 Safety
All statements regarding safety of operation and technical data in this instruction
manual will only apply when the unit is operated correctly. Handle all optics with
care. Gloves are recommended for optic installations. Take care when tightening
optics, as overtightening optics may cause the optic to break or shatter.
Filter Cube Assembly Chapter 2: Assembly Instructions
Page 2 TTN013161-D02
Chapter 2 Assembly Instructions
2.1. Step 1
Carefully unpack the TLV-U-FF Filter Cube assembly. Use a Thorlabs SM1
Spanner Wrench (such as Item # SPW602) to remove the retaining rings from
the excitation and emission ports (see Figure 1).
Figure 1 Filter Cube Assembly with Retaining Rings
Note the orientation of the retaining rings. The side of the retaining ring with the
spanner wrench slots should always face away from the cube.
2.2. Step 2
Remove the two screws holding the filter cube together (see Figure 1; Phillips
head, M2 threaded). Carefully separate the two filter cube halves. Take note of
the excitation/emission filter halves (see Figure 2).
Figure 2 Disassembling the Filter Cube
Retaining Rings
Screws
Excitation
Filter Half Emission
Filter Half
Filter Cube Assembly Chapter 2: Assembly Instructions
Rev A, November 7, 2016 Page 3
2.3. Step 3
The TLV-U-FF Filter Cube holds a standard set of Dichroic Mirror
(up to 25.2 x 36.0 x 1.1 mm), Emission (Ø25 mm), and Excitation Filters
(Ø25 mm), sold separately. Thorlabs’ MDF-GFP Filter Set is shown in Figure 3.
Figure 3 Dichroic Filter Set for Fluorescence Imaging
Thorlabs’ emission and excitation filters can be easily differentiated by the
thickness of the filter mount rings: emission (3.5 mm) and excitation (5.0 mm).
Note that the dichroic mirror has a beamsplitter coating on one side (see Figure
4).
Figure 4 Dichroic Filter Orientation
When held at an angle, the beamsplitter-coated side will appear uniform in
reflection all the way to the edge. The opposite side, when held at the same
angle, will not have a uniform reflection near the edge. There will be a band of
transmission that appears through the substrate. It is important to determine the
beamsplitter-coated side of the dichroic mirror as there is only one orientation
that will work with the filter cube.
Edge
Transmission
is Visible
Coating
Extends to
the Edge
Dichroic Mirror
Emission Filter
Excitation Filter
Filter Cube Assembly Chapter 2: Assembly Instructions
Page 4 TTN013161-D02
2.4. Step 4
Place the dichroic mirror in the emission filter half’s slot. The surface of the
dichroic mirror with the beamsplitter coating must face UP.
Figure 5 The dichroic mirror is inserted into the emission filter half.
2.5. Step 5
Align the excitation filter half with the notch on the emission filter half as shown in
Figure 6. Alternate tightening between the two assembly screws taking care not
to allow movement of the dichroic mirror.
Check the orientation of the dichroic mirror by looking into the excitation and
emission sides of the filter cube. The reflective (beamsplitter-coated) side should
be visible through the excitation side of the cube.
Figure 6 Reassembling the Filter Cube and Checking Dichroic Mirror Orientation
Excitation
Filte
r
Half
Emission
Filte
r
Half
Emission
Filte
r
Half
Dichroic Mirror
(Beamsplitter-
Coated Side Must
Face U
p
)
Emission
Side
Excitation
Side
(Coated)
Filter Cube Assembly Chapter 2: Assembly Instructions
Rev A, November 7, 2016 Page 5
2.6. Step 6
Orient the filter cube so the emission side is facing up. Insert the emission filter in
the filter cube with the arrow facing away from the cube as shown in Figure 7.
Thread an SM1 retaining ring above the filter to secure it.
Note: The emission filter will not be parallel with the face of the cube.
Orient the filter cube so the excitation side is facing up. Insert the excitation filter
with the arrow pointing towards the cube and dichroic mirror, as shown in Figure
7. Thread the other SM1 retaining ring into the excitation port to secure the filter.
Figure 7 Installing the Excitation and Emission Filters
Emission Filter
Excitation Filter
Retaining Ring
Retaining Ring
Filter Cube Assembly Chapter 2: Assembly Instructions
Page 6 TTN013161-D02
The assembled TLV-U-FF Filter Cube is shown in Figure 8.
Figure 8 Filter Cube with Filters Installed
Filter Cube Assembly Chapter 3: Regulatory
Rev A, November 7, 2016 Page 7
Chapter 3 Regulatory
As required by the WEEE (Waste Electrical and Electronic Equipment Directive)
of the European Community and the corresponding national laws, Thorlabs offers
all end users in the EC the possibility to return “end of life” units without incurring
disposal charges.
This offer is valid for Thorlabs electrical and electronic equipment:
Sold after August 13, 2005
Marked correspondingly with the crossed out
“wheelie bin” logo (see right)
Sold to a company or institute within the EC
Currently owned by a company or institute
within the EC
Still complete, not disassembled and not
contaminated
As the WEEE directive applies to self contained
operational electrical and electronic products, this end of
life take back service does not refer to other Thorlabs products, such as:
Pure OEM products, that means assemblies to be built into a unit by the
user (e.g. OEM laser driver cards)
Components
Mechanics and optics
Left over parts of units disassembled by the user (PCB’s, housings etc.).
If you wish to return a Thorlabs unit for waste recovery, please contact Thorlabs
or your nearest dealer for further information.
Waste Treatment is Your Own Responsibility
If you do not return an “end of life” unit to Thorlabs, you must hand it to a
company specialized in waste recovery. Do not dispose of the unit in a litter bin
or at a public waste disposal site.
Ecological Background
It is well known that WEEE pollutes the environment by releasing toxic products
during decomposition. The aim of the European RoHS directive is to reduce the
content of toxic substances in electronic products in the future.
The intent of the WEEE directive is to enforce the recycling of WEEE. A
controlled recycling of end of life products will thereby avoid negative impacts on
the environment.
Wheelie Bin Logo
Chapter Thorlabs Worldwide Contacts
USA, Canada, and South America
Thorlabs, Inc.
56 Sparta Avenue
Newton, NJ 07860
USA
Tel: 973-300-3000
Fax: 973-300-3600
www.thorlabs.com
www.thorlabs.us (West Coast)
Email: [email protected]
Support: [email protected]
UK and Ireland
Thorlabs Ltd.
1 Saint Thomas Place
Ely CB7 4EX
Great Britain
Tel: +44 (0) 1353-654440
Fax: +44 (0) 1353-654444
www.thorlabs.com
Email: [email protected]
Support: [email protected]
Europe
Thorlabs GmbH
Hans-Böckler-Str. 6
85221 Dachau / Munich
Germany
Tel: +49-(0) 8131-5956-0
Fax: +49-(0) 8131-5956-99
www.thorlabs.de
Email: [email protected]
Scandinavia
Thorlabs Sweden AB
Bergfotsgatan 7
431 35 Mölndal
Sweden
Tel: +46-31-733-30-00
Fax: +46-31-703-40-45
www.thorlabs.com
Email: [email protected]
France
Thorlabs SAS
109, rue des Côtes
78600 Maisons-Laffitte
France
Tel: +33 (0) 970 444 844
Fax: +33 (0) 825 744 800
www.thorlabs.com
Email: [email protected]
Brazil
Thorlabs Vendas de Fotônicos Ltda.
Rua Riachuelo, 171
São Carlos, SP 13560-110
Brazil
Tel: +55-16-3413 7062
Fax: +55-16-3413 7064
www.thorlabs.com
Email: [email protected]
Japan
Thorlabs Japan, Inc.
3-6-3, Kitamachi,
Nerima-ku, Tokyo 179-0081
Japan
Tel: +81-3-6915-7701
Fax: +81-3-6915-7716
www.thorlabs.co.jp
Email: [email protected]
China
Thorlabs China
Room A101, No. 100, Lane 2891,
South Qilianshan Road
Putuo District
Shanghai 200331
China
Tel: +86 (0) 21-60561122
Fax: +86 (0) 21-32513480
www.thorlabschina.cn
Email: [email protected]
Filter Cube Assembly Chapter 4: Thorlabs Worldwide Contacts
Page 8 TTN013161-D02
www.thorlabs.com
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11

THORLABS TLV-U-FF User manual

Brand
THORLABS
Model
TLV-U-FF
Type
User manual
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents