THORLABS LFES1 Installation guide

Type
Installation guide

THORLABS LFES1 is a sturdy shelf designed for use with the LFE1220 and LFE1220W Optical Table Enclosures. It provides extra storage space within the enclosures, raising controllers and equipment off the table's work surface while keeping them within easy reach.

THORLABS LFES1 is a sturdy shelf designed for use with the LFE1220 and LFE1220W Optical Table Enclosures. It provides extra storage space within the enclosures, raising controllers and equipment off the table's work surface while keeping them within easy reach.

LFES1
Shelf for LFE Series
Enclosure Frames
Installation Guide
Original Instructions
LFES1 Shelf for LFE Series Enclosure Frames
Table of Contents
Chapter 1 Introduction ........................................................................................................ 1
Chapter 2 Installation .......................................................................................................... 3
Chapter 3 Specifications..................................................................................................... 8
Chapter 4 Thorlabs Worldwide Contacts ......................................................................... 9
LFES1 Shelf for LFE Series Enclosure Frames Chapter 1: Introduction
Rev. A, July 8, 2022 Page 1
Chapter 1 Introduction
The LFES1 Shelf has been designed to provide additional storage space within the LFE1220 and LFE1220W
Optical Table Enclosures; it raises controllers and other equipment off the work-surface of the optical table
whilst keeping them accessible. The shelf panel is slotted to improve air flow to equipment mounted on it, and
to assist in the preservation of laminar flow within the enclosure environment. The hanging rails can be
exchanged for any other length of XE25 extrusion to give a different hanging height; simply order four
extrusions of the desired hanging length.
Figure 1 LFES1 Shelf Mounted
Multiple shelving units can be stacked as shown below.
Figure 2 Two LFES1 Shelves Mounted
LFES1 Shelf for LFE Series Enclosure Frames Chapter 1: Introduction
Page 2 ETN062107-D02
Safety Information
For the continuing safety of the operators of this equipment, and the correct operation and protection of the
equipment itself, the operator should take note of the Warnings, Cautions and Notes throughout this section,
the other pages of this handbook and, where visible, on the product itself.
General Warnings and Cautions
Warning
If this equipment is used in a manner not specified by the manufacturer, the protection
provided by the equipment may be impaired. In particular, excessive moisture may impair
operation.
The equipment is for indoor use only. The equipment is not designed for use in an explosive
atmosphere.
Caution
Heavy loads should be placed towards the ends of shelf where possible, to minimize chance
of overloading.
LFES1 Shelf for LFE Series Enclosure Frames Chapter 2: Installation
Rev. A, July 8, 2022 Page 3
Chapter 2 Installation
Environmental Conditions
Warning
Operation outside the following environmental limits may adversely affect operator safety.
The unit is designed for indoor use only.
To ensure reliable operation, the unit should not be exposed to corrosive agents or excessive moisture, heat
or dust.
The unit is not designed to be used in explosive environments.
Parts List
Description
Qty
Image
Shelf Panel 1
375 mm Hanging Bar 4
LFES1 Attachment Bar 2
M6 x 40 mm Hex
Socket Screw 8
M6 x 16 mm Hex
Socket Screw
4
Large M6 Washer 8
Small M6 Washer 4
M6 Drop-in T-Nut 4
M6 Hex Key 1
LFES1 Shelf for LFE Series Enclosure Frames Chapter 2: Installation
Page 4 ETN062107-D02
Assembling the Shelf
The LFES1 Shelf is supplied as a preassembled shelf panel, four hanging bars, two mounting bars and all
required fixings and tools.
1. Lay the shelf panel with the silver face down on the table and one corner protruding over the edge.
2. Hold a XE25 Series Hanging Bar under the protruding corner cube.
3. Drop an M6 x 16 mm Socket Screw through the corner cube and screw in to secure the XE rail flush to
the cube (do not fully tighten the screws). Ensure that the lugs on the underside of the corner cube
secure correctly in the holes in the end of the Hanging Bar.
4. Repeat steps 1 and 2 to fit hanging bars to the remaining 3 corners of the shelf.
Figure 3 Fitting the Hanging Bars
5. Turn shelf so the hanging bars point up.
LFES1 Shelf for LFE Series Enclosure Frames Chapter 2: Installation
Rev. A, July 8, 2022 Page 5
6. Place an attachment bar on top of the two hanging bars as shown below.
Figure 4 Fitting the Attachment Bars
7. Fit a large M6 washer to two of the M6 x 40 mm screws supplied, then pass a screw through each end
of the attachment bar and screw into the end of the hanging bars as shown. Do not fully tighten the
screws.
8. Repeat steps 5 and 6 for the remaining attachment bar.
9. Tighten all M6 Screws.
LFES1 Shelf for LFE Series Enclosure Frames Chapter 2: Installation
Page 6 ETN062107-D02
Fitting the Shelf to the Frame
The LFES1 Shelf can be mounted to any face with Thorlabs XE profile slots. It is recommended that it be
fitted into two side by side parallel slots (e.g. in XE50 series extrusions). All the roof members of an LFE
series enclosure are suitable for this purpose. See Figure 6 for mounting options.
10. Insert an M6 T-nut into the extrusion slot at the approximate intended mounting position for the shelf.
Repeat in the parallel slot and again in the slots at the opposite end of shelf.
11. With two people, hold the shelf up to LFE frame.
12. Fit a small M6 washer to each of the four M6 x 40 mm bolts provided, followed by a large M6 washer,
then pass the bolts (two in each end of the shelf) through the slots in the attachment bars and secure
in the T-nuts fitted at step 10 as shown below. Do not fully tighten the bolts.
Figure 5 Fitting the Shelf
13. Slide shelf to desired position.
14. Tighten all four bolts.
LFES1 Shelf for LFE Series Enclosure Frames Chapter 2: Installation
Rev. A, July 8, 2022 Page 7
There are a wide variety of options for mounting the shelf to the laminar flow enclosure frames. The cross
bars of the LFE1220 and LFE1220W Enclosure Frames, which are highlighted in yellow below, are all
compatible with the LFES1 shelf mounting hardware.
Figure 6 Shelf Mounting Options
LFES1 Shelf for LFE Series Enclosure Frames Chapter 3: Specifications
Page 8 ETN062107-D02
Chapter 3 Specifications
General Specifications
Maximum Load
70.0 kg (154.0 lb)
Shelf Dimensions (W x L)
350.0 mm x 1175.0 mm (13.78" x 46.26")
Shelf Weight (Incl. Hanging Bars and Mounting Equipment)
6.74 kg (14.83 lb)
Shelf Hanging Height (with Standard Hanging Bars)
403.0 mm (15.87")
Caution
To avoid damaging shelf, do not exceed maximum loads stated by manufacturer.
LFES1 Shelf for LFE Series Enclosure Frames Chapter 4: Thorlabs Worldwide Contacts
Rev. A, July 8, 2022 Page 9
Chapter 4 Thorlabs Worldwide Contacts
For technical support or sales inquiries, please visit us at www.thorlabs.com/contact for our most up-to-date
contact information.
USA, Canada, and South America
Thorlabs, Inc.
UK and Ireland
Thorlabs Ltd.
Europe
Thorlabs GmbH
Thorlabs Sweden AB
scandinavia@thorlabs.com
France
Thorlabs SAS
Thorlabs Vendas de Fotônicos Ltda.
Japan
Thorlabs Japan, Inc.
Thorlabs China
www.thorlabs.com
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12

THORLABS LFES1 Installation guide

Type
Installation guide

THORLABS LFES1 is a sturdy shelf designed for use with the LFE1220 and LFE1220W Optical Table Enclosures. It provides extra storage space within the enclosures, raising controllers and equipment off the table's work surface while keeping them within easy reach.

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI