Metra Electronics 99-8208 User manual

Brand
Metra Electronics
Model
99-8208
Category
Motor vehicle electronics
Type
User manual
INSTALLATION INSTRUCTIONS FOR PART 99-8208
Small Flat Blade Screwdriver • Socket Wrench
1-800-221-0932 www.metraonline.com
KIT FEATURES
© COPYRIGHT 2004-2010 METRA ELECTRONICS CORPORATION
2004-2010
• DIN Head Unit Pro
visions with Pocket
• ISO DIN Head Unit Provision with Pocket
A) Radio Housing • B) ISO Brackets • C) Trim Plate
KIT COMPONENTS
TOOLS REQUIRED:
99-8208
A
B
C
TOYOTA Sienna
Applications
WIRING AND ANTENNA CONNECTIONS (Sold Separately)
Harness:
•
70-1761
- T
oyota harness 1987-up
•
TYTO-01
- Toyota amp interface harness 2003-up
Antenna Adapter:
• Not required
99-8208
•
Dash Disassembly
- 2004-2010 Toyota Sienna ---------------------------------------- 1
•
Kit Assembly
- DIN Head Unit Provision with Pocket ---------------------------- 2
- ISO DIN Head Unit Provision with Pocket ------------------------ 3
•
Final Assembly ------------------------------------------------------ 4
•
Notes ----------------------------------------------------------------- 5
TABLE OF CONTENTS
K
NOWLEDGE IS
P
OWER
Enhance your installation and fabrication skills
by enrolling in the most recognized and respected
mobile electronics school in our industry.
Log onto www.installerinstitute.com
or call 800-354-6782 for more information
and take steps toward a better tomorrow.
99-8208
1
DASH DISASSEMBLY
2004-2010 TOYOTA SIENNA
Disconnect the negative battery terminal
to prevent an accidental short circuit.
Unclip and remove panels from left and
right side of radio.
Figure A
1
2
Unclip and remove panel or speaker cover
above radio. Figure B
3
A
Remove (4) 10MM bolts from radio to
remove. Figure C
4
C
B
99-8208
2
KIT ASSEMBLY
DIN Head Unit Provision with Pocket
1
Slide the DIN cage into the Radio
Housing and secure by bending
the metal locking tabs down.
2
Slide the after-market head unit
into the cage until secure.
99-8208
3
KIT ASSEMBLY
ISO DIN HEAD UNIT PROVISIONS
1
Mount the ISO Brackets to the head
unit with the screw supplied with
the unit.
2
Slide the head unit into the radio
opening until the side clips engage.
Snap the trim plate into the radio Housing.
3
99-8208
4
FINAL ASSEMBLY
A
Locate the factory wiring harness in the dash.
Metra recommends using the proper mating
adapter and making the connections as
shown. (Isolate and individually tape off the
ends of any unused wires to prevent electrical
short circuit)
Re-connect the negative battery terminal and test
the unit for proper operation.
A) Strip wire ends back 1/2"
B) Twist ends together
C) Solder
D) Tape
1
2
Reassemble in reverse order of disassembly.
3
B
C
D
99-8208
5
NOTES
INST99-8208
1-800-221-0932 www.metraonline.com
REV. 04-27-10 © COPYRIGHT 2004-2010 METRA ELECTRONICS CORPORATION INST99-8208
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8

Metra Electronics 99-8208 User manual

Brand
Metra Electronics
Model
99-8208
Category
Motor vehicle electronics
Type
User manual
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents