2. Computers & electronics
  3. Computer components
  4. Chassis components
  5. Mounting kits
  6. Metra
  7. 99-7862
99-7862

Metra 99-7862 Specification

  • Hello! I am an AI chatbot trained to assist you with the Metra 99-7862 Specification. I’ve already reviewed the document and can help you find the information you need or explain it in simple terms. Just ask your questions, and providing more details will help me assist you more effectively!
  • What vehicles is this installation kit compatible with?
    What does this kit include?
    What tools are required for installation?
    What steps are involved in disassembling the dashboard?
    How do I assemble the kit for a DIN Head Unit?
INSTALLATION INSTRUCTIONS FOR PART 99-7862
Phillips Screwdriver • Small Flat Blade Screwdriver Or Panel Removal Tool
1-800-221-0932 www.metraonline.com
KIT FEATURES
© COPYRIGHT 2004-2007 METRA ELECTRONICS CORPORATION
APPLICATIONS
Honda Accord
2003-2007
• DIN Head Unit Provision with pocket
• ISO DIN Head Unit Provision with pocket
A) Radio Housing • B) ISO Brackets • C) ISO Trimplate • D) Radio Harness
KIT COMPONENTS
TOOLS REQUIRED:
99-7862
A
C
D
B
Dash Disassembly
- Honda Accord 2003-2007 . . . . . . . . . . . . . . . . . . . . . . . . . . 1, 2
Kit Assembly
- DIN Head Unit Provision . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
- ISO DIN Head Unit Provision . . . . . . . . . . . . . . . . . . . . . . . . . 4
Final
Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5
TABLE OF CONTENTS
99-7862
1
HONDA ACCORD 2003-2007
R
N
D
D
R
N
D
D
R
N
D
D
A
B
C
99-7862
1
2
Unsnap coin tray/ashtray from
assembly and remove. Rubber
cover may come out first but
entire assembly must be
removed to access screws
below.
(Figure B)
3
Remove (2) Phillips screws from
under coin tray/ashtray and
remove entire assembly.
(Figure C)
Disconnect the negative battery
terminal to prevent an accidental
short circuit.
Unsnap and remove shift lever
trim ring.
(Figure A)
4
DASH DISASSEMBLY
2
99-7862
DASH DISASSEMBLY
HONDA ACCORD 2003-2007
R
P
N
D
D
D
E
F
Remove (2) Phillips screws from
bottom of pocket assembly and
unsnap and remove.
(Figure D)
5
Remove (2) Phillips screws facing
up under radio/climate control
assembly.
(Figure E)
6
Unsnap and remove upper panel
(including a/c vents) and remove
(3) Phillips screws behind the
panel.
(Figure F)
7
Unclip and remove radio/climate
control assembly.
8
Tip: You can use a hook tool to
grasp the panel inside of the vent
and pull toward the rear of the
vehicle. Be careful not to scratch
the panel.
3
99-7862
KIT ASSEMBLY
Skip to step #1 in the Final
Assembly.
3
Snap
the DIN cage into the Radio
Housing and secure by bending
the metal locking tabs down.
.
(Figure A)
1
Slide the aftermarket radio into the
cage and secure.
(Figure B)
2
DIN HEAD UNIT PROVISION
A
B
4
99-7862
KIT ASSEMBLY
Slide the head unit into the radio
opening until the side clips
engage. Snap the Trim plate into
the Radio Housing.
(Figure B)
2
Skip to step #1 in the Final Assembly.
3
Mount the ISO Brackets to the
head unit with the screws sup-
plied with the unit.
(Figure A)
1
ISO DIN HEAD UNIT PROVISION
A
B
5
FINAL ASSEMBLY
A
A) Strip wire ends back 1/2"
B) Twist ends together
C) Solder
D) Tape
B
C
D
Make wiring connections using the EIA color code chart shown below and the instructions included with the head
unit. Metra recommends making connections as shown below; Strip, Splice, Solder, Tape. Isolate and individually
tape off ends of any unused wires to prevent electrical short circuit.
FINAL WIRING CONNECTIONS
99-7862
FINAL ASSEMBLY
12V Ignition / Acc . . . Red
12V Batt / Memory . . Yellow
Ground . . . . . . . . . . . Black*
Power Antenna . . . . . Blue
Amp Turn-On . . . . . . Blue / White
Amp Ground . . . . . . . Black / White
Illumination. . . . . . . . Orange
Dimmer . . . . . . . . . . Orange / White
Right Front (+) . . . . . Gray
Right Front (-). . . . . . Gray/ Black
Left Front (+) . . . . . . White
Left Front (-) . . . . . . . White / Black
Right Rear (+). . . . . . Violet
Right Rear (-) . . . . . . Violet / Black
Left Rear (+). . . . . . . Green
Left Rear (-) . . . . . . . Green / Black
METRA / EIA WIRING CODE
*NOTE: When a Black wire is not present, ground radio to vehicle chassis.
All colors may not be present on all leads due to manufacturer’s specifications.
1
Make the wiring connections from the radio harness included with this kit to the
harness included with your radio using the EIA color code shown below. (Isolate
and individually tape off the ends of any unused wires to prevent electrical short
circuit.)
3
2
Re-connect the negative battery terminal and test the unit for proper operation.
Reassemble radio and dash assemblies in reverse order of disassembly.
4
Unplug factory harness from factory radio and plug the new harness in between
the factory harness and the factory radio.
99-7862 INSTRUCTIONS
1-800-221-0932 www.metraonline.com
REV. 06/19/07 © COPYRIGHT 2004 METRA ELECTRONICS CORPORA
TION INST99-7862
/