2. Aruba
  3. R8N55A
R8N55A

Aruba R8N55A, FlexNetwork 7503X LSQM3SUPA0 Card, R8N47A, R8N48A, R8N49A, R8N53A, R8N54A, R8N56A, R8N57A, R8N58A, R8R43A User guide

  • Hello! I am an AI chatbot trained to assist you with the Aruba R8N55A User guide. I’ve already reviewed the document and can help you find the information you need or explain it in simple terms. Just ask your questions, and providing more details will help me assist you more effectively!
Manual version: AP100-20210702
BOM: 3123A24N
Part number: 5200-8242
1
HPE FlexNetwork 7503X Type A Main Processing
Unit-LSQM3SUPA0 (R8N52A)
1 Identifier
The module identifier LSQM3SUPA0 is in the upper right of the front panel.
2 Specifications
Table 1 Module specifications
Item
Specification
SDRAM 4 GB
BootROM 8 MB
Flash 4 GB
NVRAM 1 MB
Power consumption 9 W to 16 W
Ports
• 1 × console port
• 1 × USB console port
• 2 × network management ports: 1 × RJ-45 ports and 1 × SFP fiber ports
• 1 × USB port
Transmission rate
• Console port: 9600 bps to 115200 bps (default: 9600 bps)
• USB console port: ≤ 115200 bps (default: 9600 bps)
• RJ-45 network management port : 10/100/1000 Mbps, half/full duplex
• SFP network management port : 1000 Mbps
Transmission medium and
max transmission distance
• Console port: 15 m (49.21 ft) over asynchronous EIA/TIA-232 cable
• USB console port: 10 m (32.81 ft) over USB-AB cables
• RJ-45 network management ports: 100 m (328.08 ft) over Category 5
or higher twisted pair cables
• SFP network management port: See Table 3
Compatible device models HPE FlexNetwork 7503X Switch
IMPORTANT:
To verify compatibility of the
module with the software release you are using, see the release notes.
The 10/100/1000BASE-T copper port uses an RJ-45 connector.
Manual version: AP100-20210702
BOM: 3123A24N
Part number: 5200-8242
2
Figure 1 RJ-45 connector
Table 2 RJ-45 GE connector pinout
Pin
10BASE-T/100BASE-TX/1000BASE-T
Signal
1 MX_0+ Transmits and receives data.
2 MX_0- Transmits and receives data.
3 MX_1+ Transmits and receives data.
4 MX_2+ Transmits and receives data.
5 MX_2- Transmits and receives data.
6 MX_1- Transmits and receives data.
7 MX_3+ Transmits and receives data.
8 MX_3- Transmits and receives data.
Table 3 describes the SFP transceiver modules available for the SFP ports on the card.
Table 3 Gigabit SFP transceiver modules available for the module
Product
code Module
description
Central
wavelength
(nm)
Fiber diameter
(µm)
Modal
bandwidth
(MHz*km)
Max
transmission
distance
JD098B HPE X120 1G SFP
LC BX 10-U
Transceiver
TX: 1310
RX: 1490 9/125, SMF N/A 10 km (6.21 miles)
JD099B HPE X120 1G SFP
LC BX 10-D
Transceiver
TX: 1490
RX: 1310 9/125, SMF N/A 10 km (6.21 miles)
JD103A HPE X120 1G SFP
LC LH100
Transceiver 1550 9/125, SMF N/A 100 km (62.14 miles)
JD118B HPE X120 1G SFP
LC SX Transceiver 850
50/125, MMF 500 550 m (1804.46 ft)
400
62.5/125, MMF 200 275 m (902.23 ft)
160
JD119B HPE X120 1G SFP
LC LX Transceiver 1310
9/125, SMF N/A 10 km (6.21 miles)
50/125, MMF 500 550 m (1804.46 ft)
400
62.5/125, MMF 500 550 m (1804.46 ft)
PIN #8
PIN #1
Manual version: AP100-20210702
BOM: 3123A24N
Part number: 5200-8242
3
NOTE:
BIDI modules must be used in
matched pairs. If a JD098B is used at one end, a JD099B must be
used at the other end.
3 Obtaining documentation
For module installation, see HPE FlexNetwork 7500X Switch Series Installation Guide.
For software upgrade, see HPE FlexNetwork 7500X Switch Series Software Upgrade Guide.
To access documentation and support services, go to the Hewlett Packard Enterprise Support
Center website at www.hpe.com/support/hpesc.
The information in this document is subject to change without notice.
© Copyright 2021 Hewlett Packard Enterprise Development LP
5200-8242
/