Installation Manual
H3C S9500 Series Routing Switches Table of Contents
i
Table of Contents
Chapter 2 LPU Modules................................................................................................................2-1
2.1 Overview............................................................................................................................2-1
2.2 XP2 Module .......................................................................................................................2-1
2.2.1 Specifications..........................................................................................................2-1
2.2.2 Panel and LEDs ...................................................................................................... 2-2
2.2.3 Matching Cable.......................................................................................................2-2
2.3 XP4 Module .......................................................................................................................2-3
2.3.1 Specifications..........................................................................................................2-3
2.3.2 Panel and LEDs ...................................................................................................... 2-4
2.3.3 Matching Cable.......................................................................................................2-4
2.4 XK1 Module .......................................................................................................................2-4
2.4.1 Specifications..........................................................................................................2-4
2.4.2 Panel and LEDs ...................................................................................................... 2-5
2.4.3 Matching Cable.......................................................................................................2-5
2.5 GP12 Module.....................................................................................................................2-6
2.5.1 Specifications..........................................................................................................2-6
2.5.2 Panel and LEDs ...................................................................................................... 2-6
2.5.3 Matching Cable.......................................................................................................2-6
2.6 GP24 Module.....................................................................................................................2-7
2.6.1 Specifications..........................................................................................................2-7
2.6.2 Panel and LEDs ...................................................................................................... 2-8
2.6.3 Matching Cable.......................................................................................................2-8
2.7 FP20 Module......................................................................................................................2-8
2.7.1 Specifications..........................................................................................................2-8
2.7.2 Panel and LEDs ...................................................................................................... 2-9
2.7.3 Matching Cable.......................................................................................................2-9
2.8 F32G Module...................................................................................................................2-10
2.8.1 Specifications........................................................................................................2-10
2.8.2 Panel and LEDs .................................................................................................... 2-10
2.8.3 Matching Cable.....................................................................................................2-11
2.9 GT24 Module...................................................................................................................2-12
2.9.1 Specifications........................................................................................................2-12
2.9.2 Panel and LEDs .................................................................................................... 2-13
2.9.3 Matching Cable.....................................................................................................2-13
2.10 GV48 Module.................................................................................................................2-14
2.10.1 Specifications......................................................................................................2-14
2.10.2 Panel and LEDs..................................................................................................2-14
2.10.3 Matching Cable...................................................................................................2-15
Installation Manual
H3C S9500 Series Routing Switches Table of Contents
ii
2.11 FT48 Module..................................................................................................................2-15
2.11.1 Specifications......................................................................................................2-15
2.11.2 Panel and LEDs..................................................................................................2-15
2.11.3 Matching Cable...................................................................................................2-16
2.12 P4G8 Module.................................................................................................................2-17
2.12.1 Specifications......................................................................................................2-17
2.12.2 Panel and LEDs..................................................................................................2-17
2.12.3 Matching Cable...................................................................................................2-18
2.13 SP4 Module ...................................................................................................................2-18
2.13.1 Specifications......................................................................................................2-18
2.13.2 Panel and LEDs..................................................................................................2-19
2.13.3 Matching Cable...................................................................................................2-19
2.14 UP1 Module...................................................................................................................2-20
2.14.1 Specifications......................................................................................................2-20
2.14.2 Panel and LEDs..................................................................................................2-20
2.14.3 Matching Cable...................................................................................................2-20
Installation Manual
H3C S9500 Series Routing Switches Chapter 2 LPU Modules
2-1
Chapter 2 LPU Modules
2.1 Overview
The S9500 series are modular switches that are designed following industry standards.
The series can be equipped with these types of LPU modules:
z XP2 module: provides two 10GEBase-R XFP/LC/10GEBase-W XFP/LC optical
ports
z XP4 module: provides four 10GE XFP/LC optical ports (1:2 convergence)
z XK1 module: provides one 10 GE XENPAK/SC optical/electrical port
z GP12 module: provides 12 × 1000 Mbps SFP/LC electrical/optical ports
z GP24 module: provides 24 × 1000 Mbps SFP/LC optical ports
z FP20 module: provides 20 × 100 Mbps SFP/LC optical ports
z F32G module: provides four 1000 Mbps SFP/LC optical ports and 32 × 10/100
Mbps auto-sensing RJ-45 ports
z GT24 module: provides 24 × 10/100/1000 Mbps auto-sensing RJ-45 ports
z GV48 module: provides 48 × 10/100/1000 Mbps PoE-capable auto-sensing RJ-45
ports
z FT48 module: provides 48 × 10/100 Mbps ports
z P4G8 module: provides eight 1000 Mbps SFP/LC optical ports and four 155 Mbps
SFP/LC POS optical ports
z SP4 module: provides four OC-48c SFP/LC POS optical ports
z UP1 module: provides one OC-192c XFP/LC POS optical port
2.2 XP2 Module
2.2.1 Specifications
The XP2 module provides two 10GEBase-R XFP/LC/10GEBase-W XFP/LC optical
ports.
Table 2-1 XP2 module specifications
Attribute XP2
CPU MPC8245
Boot ROM 512 KB
SDRAM 128 MB/256MB
Dimensions (L × W) 366.7 × 340 mm (14.4 × 13.4 in.)
Max. power consumption 87 W
Installation Manual
H3C S9500 Series Routing Switches Chapter 2 LPU Modules
2-2
Attribute XP2
Number of ports Two
Connector XFP/LC
Rate 10 Gbps
2.2.2 Panel and LEDs
Figure 2-1 XP2 module panel
The XP2 module has two LEDs for each optical port on its panel.
Table 2-2 1000 Mbps optical port LEDs on the XP2 module
LED Status
OFF No link is present.
LINK
Green A link is present.
OFF No packets are transmitted/received on the port.
ACT
Orange blinking Packets are being transmitted/received on the port.
2.2.3 Matching Cable
The XP2 module provides two 10 Gbps XFP optical ports. To provide optical ports, you
can use these XFP optical modules.
Installation Manual
H3C S9500 Series Routing Switches Chapter 2 LPU Modules
2-3
Table 2-3 Optical interface modules available for the XP2 module
SFP module
Central
wavelength
Connector
Matching
cable
Transmission
distance
10GBase-SR
/SW-XFP
850 nm
50/125 µm
multimode
optical fiber
cable
26 m (85.3 ft) for the
62.5 µm MMF w/
160MHz*km cable;
82 m (269.0 ft) for
the 50 µm MMF w/
500MHz*km cable;
300 m (984.3 ft) for
the 50 µm MMF w/
2000MHz*km cable
10GBase-LR/
LW-XFP
1310 nm
9/125 µm
single mode
optical fiber
cable
10 km (6 mi)
10GBase-ER
/EW-XFP
1550 nm
LC
9/125 µm
single mode
optical fiber
cable
40 km (25 mi)
2.3 XP4 Module
2.3.1 Specifications
The XP4 module provides four 10GE XFP/LC optical ports (1:2 convergence).
Table 2-4 XP4 module specifications
Attribute XP2
CPU MPC8245
Boot ROM 512 KB
SDRAM 128 MB/256MB
Dimensions (L × W) 366.7 × 340 mm (14.4 × 13.4 in.)
Number of ports Four
Max. power consumption (with bottom plate) 160 W
Connector XFP/LC
Rate 10 Gbps
Installation Manual
H3C S9500 Series Routing Switches Chapter 2 LPU Modules
2-4
2.3.2 Panel and LEDs
Figure 2-2 XP4 module panel
The XP4 module has two LEDs for each optical port on its panel.
Table 2-5 1000 Mbps optical port LEDs on the XP4 module
LED Status
OFF No link is present.
LINK
Green A link is present.
OFF No packets are transmitted/received on the port.
ACT
Orange blinking Packets are being transmitted/received on the port.
2.3.3 Matching Cable
The XP4 module provides four 10 Gbps XFP optical ports. For more details about XFP
optical modules, see
Table 2-3.
2.4 XK1 Module
2.4.1 Specifications
The XK1 module provides one 10GE XENPAK/SC optical/electrical port.
Table 2-6 XK1 module specifications
Attribute XK1
CPU MPC8245
Boot ROM 512 KB
SDRAM 128 MB/256 MB
Dimensions (L × W) 366.7 × 340 mm(14.4 × 13.4 in.)
Max. power consumption 45 W
Number of ports One
Connector XENPAK/SC
Rate 10 Gbps
Installation Manual
H3C S9500 Series Routing Switches Chapter 2 LPU Modules
2-5
2.4.2 Panel and LEDs
Figure 2-3 XK1 module panel
The XK1 module has two port LEDs for the 10GE port on its panel.
Table 2-7 Port LEDs on the XK1 module
LED Status
OFF No link is present.
LINK
Green ON A link is present.
OFF No packets are transmitted/received on the port.
ACT
Orange blinking Packets are being transmitted/received on the port.
2.4.3 Matching Cable
The XK1 module provides one 10GE XENPAK/SC optical or electrical port. You can
use these XENPAK optical modules.
Table 2-8 Interface modules available for the XK1 module
SFP module
Central
wavelength
Conne
ctor
Matching
cable
Transmission
distance
10GBASE-S
R-XENPAK
850 nm
Multimode
optical fiber
cable
26 m (85.3 ft) for the
62.5 µm MMF w/
160MHz*km cable;
82 m (269.0 ft) for the
50 µm MMF w/
500MHz*km cable;
300 m (984.3 ft) for the
50 µm MMF w/
2000MHz*km cable
10GBASE-L
R-XENPAK
1310 nm 10 km (6 mi)
40 km (25 mi)
10GBASE-E
R-XENPAK
1550 nm
SC
Single mode
optical fiber
cable
80 km (50 mi)
Installation Manual
H3C S9500 Series Routing Switches Chapter 2 LPU Modules
2-6
2.5 GP12 Module
2.5.1 Specifications
The GP12 module provides 12 × 1000 Mbps SFP/LC optical ports.
Table 2-9 GP12 module specifications
Attribute GP12
CPU MPC8245
Boot ROM` 512 KB
SDRAM 128 MB/256 MB
Dimensions (L × W) 366.7 × 340 mm (14.4 × 13.4 in.)
Max. power consumption 55 W
Number of ports 12
Connector SFP/LC
Rate 1000 Mbps
2.5.2 Panel and LEDs
Figure 2-4 GP12 module panel
The GP12 module has two LEDs for each port on its panel.
Table 2-10 Port LEDs on the GP12 module
LED Status
OFF No link is present.
LINK
Green A link is present.
OFF No packets are transmitted/received on the port.
ACT
Orange blinking Packets are being transmitted/received on the port.
2.5.3 Matching Cable
The GP12 module can provide 12 × 1000 Mbps optical ports. You can use these SFP
optical modules:
Installation Manual
H3C S9500 Series Routing Switches Chapter 2 LPU Modules
2-7
Table 2-11 Interface modules available for the GP12 module
SFP module
Central
wavelength
Connector
Matching
cable
Transmission
distance
50/125 µm
multimode
optical fiber
cable
550 m (1804
ft)
1000BASE-SX-SFP 850 nm
62.5/125 µm
multimode
optical fiber
cable
275 m (902 ft)
1000BASE-LX-SFP 10 km (6 mi)
1000BASE-LH-SFP
1310 nm
1000BASE-ZX-LR-
SFP
40 km (25 mi)
1000BASE-ZX-VR-
SFP
70 km (43 mi)
1000BASE-ZX-UR-
SFP
1550 nm
LC
9/125 µm
single mode
optical fiber
cable
100km (62 mi)
2.6 GP24 Module
2.6.1 Specifications
The GP24 module provides 24 × 1000 Mbps SFP/LC optical ports.
Table 2-12 GP24 module specifications
Attribute GP24
CPU MPC8245
Boot ROM 512 KB
SDRAM 128 MB/256MB
Dimensions (L × W) 366.7 × 340 mm (14.4 × 13.4 in.)
Max. power consumption 100 W
Number of ports 24
Connector SFP/LC
Rate 1000 Mbps
Installation Manual
H3C S9500 Series Routing Switches Chapter 2 LPU Modules
2-8
2.6.2 Panel and LEDs
Figure 2-5 GP24 module panel
The GP24 module has two LEDs for each 1000 Mbps optical port on its panel.
Table 2-13 Port LEDs on the GP24 module
LED Status
OFF No link is present.
LINK
Green A link is present.
OFF No packets are transmitted/received on the port.
ACT
Orange blinking Packets are being transmitted/received on the port.
2.6.3 Matching Cable
The GP24 module provides 24 × 1000 Mbps optical ports. For more details about SFP
optical modules, see
Table 2-11
2.7 FP20 Module
2.7.1 Specifications
The FP20 module provides 20 × 100 Mbps SFP/LC optical ports.
Table 2-14 FP20 module specifications
Attribute FP20
CPU MPC8245
Boot ROM 512 KB
SDRAM 128 MB/256 MB
Dimensions (L × W) 366.7 × 340 mm (14.4 × 13.4 in.)
Max. power consumption 50W
Port 20
Connector SFP/LC
Rate 100 Mbps full duplex
Installation Manual
H3C S9500 Series Routing Switches Chapter 2 LPU Modules
2-9
2.7.2 Panel and LEDs
Figure 2-6 FP20 module panel
The FP20 module has two LEDs for each port on its panel.
Table 2-15 Port LEDs on FP20 module
LED Status
OFF No link is present.
LINK
Green A link is present.
OFF No packets are transmitted/received on the port.
ACT
Orange blinking Packets are being transmitted/received on the port.
2.7.3 Matching Cable
The FP20 module provides 20 × 100 Mbps SFP optical ports. You can use these SFP
optical modules:
Table 2-16 Interface modules available for the FP20 module
SFP module
Central
wavelength
Connector Matching cable
Transmission
distance
50/125 µm
multimode
optical fiber
cable
100BASE-FX-
MM-SFP
62.5/125 µm
multimode
optical fiber
cable
2 km (1 mi)
100BASE-FX-
SM-SFP
15 km (9 mi)
100BASE-FX-
SM-LR-SFP
1310 nm
40 km (25 mi)
100BASE-FX-
SM-VR-SFP
1550 nm
LC
9/125 µm single
mode optical
fiber
80 km (50 mi)
Installation Manual
H3C S9500 Series Routing Switches Chapter 2 LPU Modules
2-10
2.8 F32G Module
2.8.1 Specifications
The F32G module provides four 1000 Mbps SFP/LC optical ports and 32 x 10/100
Mbps auto-sensing RJ-45 ports.
Table 2-17 F32G module specifications
Attribute F32G
CPU MPC8245
Boot ROM 512 KB
SDRAM 128 MB/256 MB
Dimensions (L × W) 366.7 × 340 mm (14.4 × 13.4 in.)
Max. power consumption 55 W
Number of ports
Four 1000 Mbps SFP/LC optical ports
32 x 10/100 Mbps auto-sensing RJ-45 ports
Connector RJ-45, SFP/LC
Rate
10 Mbps, half/full duplex
100 Mbps, half/full duplex
1000 Mbps, full duplex
2.8.2 Panel and LEDs
Figure 2-7 F32G module panel
The F32G module has two LEDs for each 1000 Mbps port on its panel.
Table 2-18 1000 Mbps port LEDs on the F32G module
LED Status
OFF No link is present.
LINK
Green A link is present.
OFF No packets are transmitted/received on the port.
ACT
Orange blinking Packets are being transmitted/received on the port.
The F32G module has one LED for each 100 Mbps port on its panel.
Installation Manual
H3C S9500 Series Routing Switches Chapter 2 LPU Modules
2-11
Table 2-19 100 Mbps port LEDs on F32G module
LED Status
ON A link is present on the port.
OFF No link is present on the port.
LINK/ACT
Blinking Packets are being transmitted/received on the port.
2.8.3 Matching Cable
The F32G can provide four 1000 Mbps SFP optical ports. For more details about the
SFP modules, see
Table 2-11.
The 32 × 10/100 Mbps electrical ports on the F32G module use RJ-45 connectors and
category-5 twisted pair cables which allow the transmission distance of 100 m (328 ft).
PIN #8
PIN #1
Figure 2-8 RJ-45 connector
Table 2-20 Pin assignment of the RJ-45 MDI connector
10Base-T/100Base-TX
Pin No.
Signal Function
1 Tx+ Transmit data.
2 Tx- Transmit data.
3 Rx+ Receive data.
4 Reserved -
5 Reserved -
6 Rx- Receive data.
7 Reserved -
8 Reserved -
Installation Manual
H3C S9500 Series Routing Switches Chapter 2 LPU Modules
2-12
Table 2-21 Pin assignment of the RJ-45 MDI-X connector
10Base-T/100Base-TX
Pin No.
Signal Function
1 Rx+ Receive data.
2 Rx- Receive data.
3 Tx+ Transmit data.
4 Reserved -
5 Reserved -
6 Tx- Transmit data.
7 Reserved -
8 Reserved -
Note:
Tx = Transmit data; Rx = Receive data
2.9 GT24 Module
2.9.1 Specifications
The GT24 module provides 24 × 10/100/1000 Mbps auto-sensing RJ-45 ports.
Table 2-22 GT24 module specifications
Attribute GT24
CPU MPC8245
Boot ROM 512 KB
SDRAM 128 MB/256 MB
Dimensions (L × W) 366.7 × 340 mm (14.4 × 13.4 in.)
Max. power consumption 110 W
Number of ports 24
Connector RJ-45
Rate 10/100/1000 Mbps
Installation Manual
H3C S9500 Series Routing Switches Chapter 2 LPU Modules
2-13
2.9.2 Panel and LEDs
Figure 2-9 GT24 module panel
The GT24 module has one LEDs for each port on its panel.
Table 2-23 Port LEDs on the GT24 module
LED Status
ON No link is present.
OFF A link is present.
LINK/ACT
Blinking Packets are being transmitted/received on the port.
2.9.3 Matching Cable
The ports on the GT24 module uses RJ-45 connectors (see Table 2-24) and category-5
twisted pair cables which allow the transmission distance of 100 m (328 ft).
PIN #8
PIN #1
Figure 2-10 RJ-45 connector
Table 2-24 Pin assignment of the RJ-45 GE connector
10Base-T/100Base-T/1000Base-TX
Pin No.
Signal Function
1 MX_0+ Transmit and receive data.
2 MX_0- Transmit and receive data.
3 MX_1+ Transmit and receive data.
4 MX_2+ Transmit and receive data.
5 MX_2- Transmit and receive data.
6 MX_1- Transmit and receive data.
Installation Manual
H3C S9500 Series Routing Switches Chapter 2 LPU Modules
2-14
10Base-T/100Base-T/1000Base-TX
Pin No.
Signal Function
7 MX_3+ Transmit and receive data.
8 MX_3- Transmit and receive data.
2.10 GV48 Module
2.10.1 Specifications
The GV48 module provides 48 x 10/100/1000 Mbps auto-sensing PoE-capable RJ-45
ports.
Table 2-25 GV48 module specifications
Attribute GV48
CPU MPC8245
BootROM 512 KB
SDRAM 256 MB
Dimensions (L× W) 366.7 × 340 mm (14.4 × 13.4 in.)
Number of ports 48
Connector RJ-45
Rate 10/100/1000 Mbps
2.10.2 Panel and LEDs
Figure 2-11 GV48 module panel
The GV48 module has one LED for each port on its panel.
Table 2-26 1000 Mbps electrical port LEDs on the GV48 module
LED Status
ON A link is present.
OFF No link is present.
LINK/ACT
Blinking Packets are being transmitted/received on the port.
Installation Manual
H3C S9500 Series Routing Switches Chapter 2 LPU Modules
2-15
2.10.3 Matching Cable
For more details, see section 2.9.3 Matching Cable
2.11 FT48 Module
2.11.1 Specifications
The FT48 module provides 48 x 10/100 Mbps auto-sensing RJ-45 ports.
Table 2-27 FT48 module specifications
Attribute FT48
CPU MPC8245
Boot ROM 512 KB
SDRAM 128 MB/256 MB
Dimensions (L × W) 366.7 × 340 mm (14.4 × 13.4 in.)
Max. power consumption 55 W
Port 48
Connector RJ-45
Rate
10 Mbps, half/full duplex
100 Mbps, half/full duplex
2.11.2 Panel and LEDs
FT48A
Figure 2-12 FT48 module panel
The FT48 module has one LED for each port on its panel.
Table 2-28 Port LEDs on FT48 module
LED Status
ON A link is present.
OFF No link is present.
LINK/ACT
Blinking Packets are being transmitted/received on the port.
Installation Manual
H3C S9500 Series Routing Switches Chapter 2 LPU Modules
2-16
2.11.3 Matching Cable
The FT48 module uses RJ-45 connectors and category-5 twisted pair cables which
allow the transmission distance of 100 m.
PIN #8
PIN #1
Figure 2-13 RJ-45 connector
Table 2-29 Pin assignment of the RJ-45 MDI connector
10Base-T/100Base-TX
Pin No.
Signal Functionality
1 Tx+ Transmit data.
2 Tx- Transmit data.
3 Rx+ Receive data.
4 Reserved -
5 Reserved -
6 Rx- Receive data.
7 Reserved -
8 Reserved -
Table 2-30 Pin assignment of RJ-45 MDI-X connector
10Base-T/100Base-TX
Pin No.
Signal Functionality
1 Rx+ Receive data.
2 Rx- Receive data.
3 Tx+ Transmit data.
4 Reserved -
5 Reserved -
6 Tx- Transmit data.
7 Reserved -
8 Reserved -
Installation Manual
H3C S9500 Series Routing Switches Chapter 2 LPU Modules
2-17
Note:
Tx = Transmit data; Rx = Receive data
2.12 P4G8 Module
2.12.1 Specifications
The P4G8 module provides eight 1000 Mbps SFP/LC optical ports and four
OC-3c-POS optical ports.
Table 2-31 P4G8 module specifications
Attribute P4G8
CPU MPC8245
Boot ROM 512 KB
SDRAM 128 MB/256 MB
Dimensions (L × W) 366.7 × 340 mm (14.4 × 13.4 in)
Max. power consumption 55 W
Number of ports
Eight 1000 Mbps SFP/LC optical ports Four
OC-3c-POS optical ports.
Connector SFP/LC
Rate
1000 Mbps
155 Mbps
2.12.2 Panel and LEDs
Figure 2-14 P4G8 module panel
The P4G8 module has two LEDs for each port on its panel.
Table 2-32 1000 Mbps port LEDs on the P4G8 module
LED Status
OFF No link is present.
LINK
Green A link is present.
Installation Manual
H3C S9500 Series Routing Switches Chapter 2 LPU Modules
2-18
LED Status
OFF No packets are transmitted/received on the port.
ACT
Orange blinking Packets are being transmitted/received on the port.
Table 2-33 POS port LEDs on the P4G8 module
LED Status
OFF The link is normal.
ALM
ON No link is present or the link is faulty.
OFF No packets are transmitted/received on the port.
ACT
ON Packets are being transmitted/received on the port.
2.12.3 Matching Cable
The GP24 module provides eight 1000 Mbps SFP optical ports. For more details about
SFP optical modules, see
Table 2-11.
The GP24 module also provides four OC-3c-POS optical ports. For more details about
100 Mbps SFP optical modules (to provide OC-3c-POS optical ports), see
Table 2-16.
2.13 SP4 Module
2.13.1 Specifications
The SP4 module provides four OC-48c-POS optical ports.
Table 2-34 SP4 module specifications
Attribute SP4
CPU MPC8245
BootROM 512 KB
SDRAM 256 MB
Dimensions (L × W) 366.7 × 340 mm (14.4 × 13.4 in)
Max. power consumption 97 W
Number of ports Four
Connector SFP/LC
Rate 2.5 Gbps
Page is loading ...
Page is loading ...
/
