MAHA RGA Operating instructions

Fehler! Verwenden Sie die Registerkarte 'Start', um Name dem Text zuzuweisen, der hier angezeigt werden soll.Fehler! Verwenden Sie

die Registerkarte 'Start', um Name dem Text zuzuweisen, der hier angezeigt werden soll.Fehler! Verwenden Sie die Registerkarte

'Start', um Name dem Text zuzuweisen, der hier angezeigt werden soll.

RGA

Mobile Column Lift

Original Operating Instructions

BA491901-en

Pos: 1 /Te chn isc he Dokum en tat ion/ Heb etec hn ik/C OL UMNLI FT/ 49 190 1 RG A/BA/ I nhalt : 491 9 Ti telb ild @ 42\mod_ 1431 9503 18774_ 0.doc x @ 22436 64 @ @ 1

Pos: 2 /-----F or m at---- -/MAN UELLER UM BRUCH Sei tenumb ruch @ 0\mod _ 113 44 03 577 6 87_ 0.d

Pos: 2 /-----F or m at---- -/MAN UELLER UM BRUCH Sei tenumb ruch @ 0\mod _113 44035 77687_ 0.d ocx @ 127 7 @ @ 1

BA491901-en

Pos: 3 /-----F or ma t-----/ Inha ltsv er zeic hnis - 3 Ebene n @ 5\mod_ 11688 67441 046_ 75.do cx @ 729 20 @ @ 1

Contents

1 Safety ...................................................................................................................... 5

1.1 Introduction ......................................................................................................................................... 5

1.2 Symbols .............................................................................................................................................. 5

1.3 Intended Use ....................................................................................................................................... 5

1.4 Inappropriate Use ................................................................................................................................ 5

1.5 Requirements on Operating and Service Personnel ............................................................................. 5

1.6 Safety Instructions for Commissioning ................................................................................................. 5

1.7 Safety Instructions for Operation ......................................................................................................... 6

1.8 Safety Instructions for Servicing ........................................................................................................... 6

1.9 What to Do in the Event of Defects or Malfunctions ............................................................................. 6

1.10 What to Do in the Event of an Accident ............................................................................................... 6

1.11 Safety Features ................................................................................................................................... 7

1.11.1 Locking Device .................................................................................................................................... 7

1.11.2 Braking Motor ..................................................................................................................................... 7

1.11.3 Thermal Overload Protection ............................................................................................................... 7

1.11.4 Safety Shutdown after Motor Overload ................................................................................................ 7

1.11.5 Warning and Information Labels .......................................................................................................... 7

2 Description ............................................................................................................... 8

2.1 Design and Operating Principle ........................................................................................................... 8

2.2 Specifications ...................................................................................................................................... 9

2.3 Sample Nameplate ............................................................................................................................ 10

2.4 Noise Emission .................................................................................................................................. 10

3 Operation ............................................................................................................... 11

3.1 Initial Operation ................................................................................................................................. 11

3.2 Main Switch....................................................................................................................................... 11

3.3 Control Unit ....................................................................................................................................... 12

3.4 Positioning, Logging in and Interconnecting the Columns ................................................................. 14

3.5 Switching over to Group Mode .......................................................................................................... 15

3.6 Switching over to Single Mode .......................................................................................................... 15

3.7 Raising and Lowering ........................................................................................................................ 15

3.8 Shutdown .......................................................................................................................................... 16

3.9 Emergency-down Function, Mechanical ............................................................................................ 16

3.10 Handling / Moving the Columns ........................................................................................................ 17

3.11 Transverse Beam for Semitrailers ...................................................................................................... 18

4 Maintenance .......................................................................................................... 19

4.1 Annual Inspection .............................................................................................................................. 19

4.2 Care Instructions ............................................................................................................................... 19

4.3 Lubrication ........................................................................................................................................ 19

4.3.1 Lubricants ......................................................................................................................................... 19

4.3.2 Recirculating Ball Nut ........................................................................................................................ 20

BA491901-en

4.3.3 Moving Gear ...................................................................................................................................... 21

4.3.4 Options ............................................................................................................................................. 21

4.3.5 Thrust Washers ................................................................................................................................. 22

4.4 Setting the Hydraulic Jack ................................................................................................................. 25

4.5 Battery Charge Condition .................................................................................................................. 26

4.6 Troubleshooting ................................................................................................................................ 27

4.7 Spare Parts ....................................................................................................................................... 29

5 Service Lifetime ...................................................................................................... 29

6 Dismantling ............................................................................................................ 29

7 Disposal ................................................................................................................. 29

8 Contents of the Declaration of Conformity .............................................................. 29

9 Company Information ............................................................................................. 30

Pos: 4 /-----F or m at---- -/MAN UELLER UM BRUCH Sei tenumb ruch @ 0\mod _113 44035 77687_ 0.d ocx @ 127 7 @ @ 1

BA491901-en

Pos: 5 /-----F or ma t-----/ MANUEL LER UMB RUCH Seite numbruc h @ 0\mod_ 11344 03577 687_ 0.docx @ 1277 @ @ 1

BA491901-en

Pos: 6 / Technisc he D okumen tation/A lle Gerä te/ Überschrif ten/Über schr iften 1/S/ Über schrift 1: Sich erhei t @ 6\mod_1174482399906_75.docx @ 76962 @ 1 @ 1

Safety

Pos: 7 / Techn isc he D okumen tati on/A lle Ger äte/ Übe rschr ifte n/Über schr iften 1.1/ E/Übe rsc hrif t 1. 1: Einf ühru ng @ 6\mod_1174482219062_75.docx @ 76793 @ 2 @ 1

1.1

Introduction

Pos: 8 / Te chnisc he D okum entat ion/A lle G erä te/In halte/ Sic herhe it/In halt : Einf ühru ng Si cher heit @ 6\mod_1175609639562_75.docx @ 87528 @ @ 1

Thoroughly read this manual before operating the equipment and comply with the instructions.

Always display the manual in a conspicuous location.

Personal injury and property damage incurred due to non-compliance with these safety

instructions are not covered by the product liability regulations.

Pos: 9 / Technisc he D okumen tation/A lle Gerä te/ Überschrif ten/Über schr iften 1 .1/S/ Überschri ft 1.1: Symb ole @ 6\mod_1174482270875_75.docx @ 76865 @ 2 @ 1

1.2

Symbols

Pos: 10 /Tec hnische Dokume ntat ion/Alle Geräte/ Inhal te/Sich erheit/In halt: Symbo le Sicher heit @ 14\mod_1239866667866_75.docx @ 361518 @ @ 1

Important safety instructions. Failure to comply with instructions could result in personal injury or

property damage.

Important information.

Pos: 11 /Techn ische Dokument ation/Alle Ger äte/Übersc hriften/ Überschrifte n 1.1/B/Über schrift 1.1: Bestimm ungsgem äßer Gebrau ch @ 6\mod_117 6734 02220 3_75.d ocx @ 88746 @ 2 @ 1

1.3

Intended Use

Pos: 12 / Tec hnis che Dokum entatio n/Hebetech nik/- Arc hiv -/ 49 Rad greif er-Hebeb ühnen/ 0001 Radgreifer -Hebeb ühne n Alle/I nhalte/ Inhalt: Bestimm ungsg emäßer Gebr auch RG-H BZ @ 1 1\mod_1227608538981_75.docx @ 275048 @ @ 1

• This lift is to be used exclusively for the safe lifting of commercial and agricultural vehicles such

as trucks, buses, tractors etc. Observe the rated load capacity.

• The lift may not be modified without the express written consent of the manufacturer. In case of

non-compliance the declaration of conformity becomes void.

Pos: 13 /Techn ische Dokument ation/Alle Ger äte/Übersc hriften/ Überschrifte n 1.1/B/Über schrift 1.1: Bestimm ungsw idriger Gebrauc h @ 18\mod_1255530265027_75.docx @ 471571 @ 2 @ 1

1.4

Inappropriate Use

Pos: 1 4 /Tec hn ische Dokum ent ation/ Hebet echnik/- Arch iv -/ 00 H ebet echnik - Alle/Inha lte/Inhalt: Best immungsw idriger Gebra uch HBZ @ 19\mod_1267188702628_75.docx @ 794843 @ @ 1

Any use other than described is inappropriate, for example:

• Climbing on the lift supports

• Transporting persons on the lift supports

• Usage as mobile work platform or for other lifting operations

Pos: 15 / Techn ische Dokument ation/ Alle Ger äte/Über schr iften/ Überschri ften 1.1/A/Über schr ift 1. 1: Anf orderun gen a n das Bed ienun gs - und Serv iceper sonal @ 34\mod_1380637497630_75.docx @ 1835413 @ 2 @ 1

1.5

Requirements on Operating and Service Personnel

Pos: 16 / Techn ische Dokument ation/ Alle Ger äte/I nhalte/Si cher heit/In halt: Anf orderun gen a n das B edienu ngs- u nd Serviceperso nal @ 35\mod_1390296255225_75.docx @ 187664 8 @ @ 1

All persons employed in the operation, maintenance, installation, removal and disposal of the de-

vice must

• be at least 18 years old,

• be trained and instructed in writing,

• have read and understood this manual

• be on record as having been instructed in safety guidelines.

Pos: 17 / Techn ische Dokument ation/ Alle Ger äte/Über schr iften/ Überschri ften 1.1/S/Über schr ift 1. 1: Sicher heits vorschr iften f ür die I nbetr iebnahm e @ 6\mod_1174482269156_75.docx @ 76838 @ 2 @ 1

1.6

Safety Instructions for Commissioning

Pos: 18 / Techn ische Dokument ation/ Hebetech nik/ - Arch iv -/ 49 Rad greifer -Hebebüh nen/0 001 Rad greifer-H ebeb ühne n A lle/I nhalt e/Inh alt: S icher hei tsvor schr iften für d ie Inb etr iebna hme RG-HB Z @ 6\mod_1178094134921_75.docx @ 90757 @ @ 1

• Use the lift on a hard, level surface only.

BA491901-en

• The standard lift version may not be installed and commissioned in the vicinity of explosives or

flammable liquids.

Pos: 19 /Techn ische Dokument ation/Alle Ger äte/Übersc hriften/ Überschrifte n 1.1/S/Übersc hrift 1.1: Sicher heits vorschr iften f ür den Betrieb @ 6\mod_1174482268953_75.docx @ 76826 @ 2 @ 1

1.7

Safety Instructions for Operation

Pos: 20 / Techn ische Dokument ation/ Hebetech nik/ - Arch iv -/ 49 Rad greifer -Hebebüh nen/0 001 Rad greifer-H ebeb ühne n A lle/I nhalt e/Inh alt: Sic herhei tsvorschr iften für de n Betri eb RG-H BZ @ 6\mod_1178094657921_75.docx @ 90770 @ @ 1

• Read the detailed operating manual.

• Lift operation by trained personnel over 18 years only.

• Do not exceed the rated load capacity per column as indicated on the lift nameplate.

• Ensure an unobstructed movement of lift and vehicle.

• After raising the vehicle briefly, stop and check the lift supports for secure contact with the ve-

hicle.

• Closely watch lift and vehicle during raising and lowering cycles.

• The working area which cannot be overviewed by the operator should be monitored by a sec-

ond person.

• When operating the lift in single or group mode, make sure the vehicle is not tilted.

• Do not allow anyone to stay in lift area during raising and lowering cycles.

• Do not allow anyone to climb on lift or inside raised vehicle.

• Keep lift and vehicle free of tools and parts.

• When using the lift outdoors, lower the vehicle and stop operation when the wind velocity ex-

ceeds 6 m/s.

• Push the support forks completely under the wheels or lift points of the vehicle to be raised.

• Do not drive over or pinch electrical cables.

Pos: 21 / Techn ische Dokument ation/ Alle Ger äte/Über schr iften/ Überschri ften 1.1/S/Über schr ift 1. 1: Sicher heits vorschr iften f ür Servi cearbeit en @ 6\mod_1174482270640_75.docx @ 76850 @ 2 @ 1

1.8

Safety Instructions for Servicing

Pos: 22 / Techn ische Dokument ation/ Hebetech nik/ - Arch iv -/ 49 Rad greifer -Hebebüh nen/0 001 Rad greifer-H ebeb ühnen A lle/Inha lte/Inh alt: S icherh eitsvors chrift en für S ervice arbeiten RG-H BZ @ 6\mod_1178095227937_75.docx @ 90793 @ @ 1

• Service work may be done by authorized service technicians only.

• Turn off and padlock the main switch before doing any repair, maintenance or setup work.

• Disconnect the mains plug before opening the control box.

• Work on the electrical equipment may be done by service technicians or certified electricians

only.

• Ensure that ecologically harmful substances are disposed of only in accordance with the ap-

propriate regulations.

• Do not use high pressure or steam jet cleaners. Use of caustic cleaning agents may damage

the lift.

• Do not replace or override the lift safety devices.

Pos: 23 / Techn ische Dokument ation/ Alle Ger äte/Über schr iften/ Überschri ften 1.1/V/ Übersc hrift 1.1 : Verh alten im Stör fall @ 6\mod_1178097008375_75.docx @ 90829 @ 2 @ 1

1.9

What to Do in the Event of Defects or Malfunctions

Pos: 24 / Techn ische Dokument ation/ Hebetech nik/ - Arch iv -/ 00 H eb etechni k - Alle/I nh alte/ I nha lt: V erh alt en im St örf all H BZ @ 19\mod_1267177095494_75.docx @ 794570 @ @ 1

• In case of defects or malfunctions such as uncontrolled lift movement or deformation of the su-

perstructure, support or lower the lift immediately.

• Turn off the main switch and secure it against unauthorized usage. Contact service.

Pos: 25 / Techn ische Dokume ntation/Alle Ger äte/Übersc hriften/ Überschrifte n 1.1/V/Übers chrift 1.1: Verh alten bei Unfällen @ 1 9\mod_ 12671 77245 337_7 5.docx @ 79460 0 @ 2 @ 1

1.10

What to Do in the Event of an Accident

Pos: 26 / Techn ische Dokument ation/ Alle Ger äte/I nhalte/Si cher heit/In halt: Ver halten bei U nfällen @ 34\m od_1381128804654_75.docx @ 1837123 @ @ 1

• The injured person is to be removed from the danger area. Find out where dressing and band-

ages are kept. Seek first-aid.

BA491901-en

• Provide first-aid (stop bleeding, immobilise injured limbs), report the accident and seal off the

accident site.

• Immediately report any accident to your supervisor. Make sure a record is kept of every occa-

sion first-aid is provided, e.g. in an accident book.

• Remain calm and answer any questions that may arise.

Pos: 27 /Tec hnisch e Dokume ntation/ Alle Gerä te/Über schrift en/Über schrif ten 1.1/S/ Übersc hrift 1. 1: Sicherhe itseinr ichtun gen @ 6\mod_ 1174 4833 24765_ 75.do cx @ 7710 3 @ 2 @ 1

1.11

Safety Features

Pos: 28 / Techn ische Dokument ation/ Hebetech nik/ COLUMN LIFT/4 91901 RGA/ BA/In halt: 49 19 Si cher heitse inri chtu ngen @ 22\mod_1293003894219_75.docx @ 959625 @ 23333 @ 1

1.11.1

Locking Device

The locking device serves to prevent inadvertent lowering motions caused by gear,

load nut or lifting screw failure. The carriage is blocked by safety wedge (1) and

counterwedge (2).

1.11.2

Braking Motor

The motors are equipped with AC spring pressure brakes. Once the motors

are switched off, the brakes prevent any further movements.

1.11.3

Thermal Overload Protection

Overload protection via electronically monitored thermoswitches.

1.11.4

Safety Shutdown after Motor Overload

The motor load is permanently monitored by the control PCB. If an overload of

≥ 15 %

occurs, the

system will switch off automatically. In this case the lift cannot be raised any more, but it can be

normally lowered to bottom position.

1.11.5

Warning and Information Labels

Do not change or remove the warning and information labels. Order replacement for defective

labels.

Pos: 29 /----- Forma t -----/M AN UEL LER UM BRUC H Se i tenu mbr uch @ 0\m od_1134403577687_0.docx @ 1277 @ @ 1

BA491901-en

Pos: 30 / Techn ische Dokument ation/ Alle Ger äte/Über schr iften/ Überschri ften 1/B/ Übersc hrift 1: Bes chreibun g @ 6\mod_1174482271453_75.docx @ 76889 @ 1 @ 1

Description

Pos: 31 / Techn ische Dokument ation/ Alle Ger äte/Über schr iften/ Überschri ften 1.1/A/Über schr ift 1. 1: Aufba u und A rbeitsp rinz ip @ 15\mod_1245311386403_75.docx @ 390861 @ 1 @ 1

2.1

Design and Operating Principle

Pos: 3 2 /Tec hn ische Dokum ent ation/ Heb etech nik/ COL UMNLIF T/4 91201 MCL/ BA/I nhalt : 49 12 A ufbau+ Arb eitspr inzip MCL/ RG B/RGA @ 11\mod_1227616300679_75.docx @ 275388 @ @ 1

•

Complete System

The complete system of the Mobile Column Lift consists of individual columns, which can be inter-

connected (e.g. 4, 6, 8 columns) and used to raise commercial vehicles. A maximum number of 8

columns per lift system can be logically interconnected.

A maximum number of 8 lift systems can be operated parallel, with information exchange on differ-

ent radio channels.

The complete system can be operated from each individual column. The columns interact via radio

communication, with each lift system using its own channel.

•

Column

The columns are mechanically designed for engaging the wheels of commercial vehicles.

They are all identical and interchangeable from system to system. Power supply is effected via a

standard three-phase connection.

•

Control

Each column is equipped with a control unit made up of the following components:

• Operating panel with display

• Microprocessor

• Pulse generators and sensors

• Watchdog monitoring

• Radio transmitter / receiver

• Drive unit

• Emergency stop switch

Pos: 33 / Tec hnis che Dokumentation/Hebetechnik/COLUMNLIFT/491201 MCL/BA/Inhalt: 4912 Steuerungsschema MCL/RGB/RGA @ 11\mod_1227620776698_75.docx @ 275412 @ @ 1

Pos: 34 /----- Forma t -----/M AN UEL LER UM BRUC H Se i tenu mbr uch @ 0\m od_1134403577687_0.docx @ 1277 @ @ 1

BA491901-en

Pos: 35 /Techn ische Dokument ation/Alle Ger äte/Übersc hriften/ Überschrifte n 1.1/T/Über schrift 1.1: Tech nische Daten @ 7\mod_1184075526343_75.docx @ 99711 @ 2 @ 1

2.2

Specifications

Pos: 36 / Tec hnis che Dokum entat ion/Heb etechni k/COL UMNLIF T/4919 01 RGA/ BA/In halt: 4 919 Tech nische Daten ( Bilder ) RGA/ RGA T @ 18\mod_1256044786303_0.docx @ 480332 @ @ 1

RGA

RGA T

Pos: 37 /----- Forma t -----/M AN UEL LER UM BRUC H Se i tenu mbr uch @ 0\mod_1134403577687_0.docx @ 1277 @ @ 1

BA491901-en

Pos: 38 / Techn ische Dokument ation/ Hebetech nik/ COLUMN LIFT/4 91901 RG A/BA/I nhalt: 4919 Technis che D aten (Tab elle) RGA/R GA T @ 18\m od_1256048339981_75.docx @ 480420 @ @ 1

RGA

RGA T

Load capacity per column 7500 kg 5000 kg

Full travel 1750 mm 1750 mm

Raising / Lowering time 113 s 113 s

Tyre diameter 900…1250 mm 600…2000 mm

Motor power 1.5 kW 1.5 kW

System of protection IP 54 IP 54

Control voltage 48 V 48 V

Charging voltage 230 V 230 V

Net weight per column 545 kg 637 kg

Surface load 0.5 N/mm2 0.5 N/mm2

Pos: 39 / Techn ische Dokument ation/ Hebetech nik/ - Arch iv -/ 00 H eb etechni k - Alle/In halte/ Info! /In halt : Inf o - Betri ebswar mer Zus tand / Tech n. Änder ungen H BZ @ 6\mod_1177427042703_75.docx @ 90160 @ @ 1

The properties indicated apply to lifts running at operating temperature.

Specifications are subject to change without notice.

Pos: 40 / Techn ische Dokument ation/ Alle Ger äte/Über schr iften/ Überschri ften 1.1/ T/ Über schr ift 1.1: Typ en sch ild-M ust er @ 11\m od_12 27622 2060 96_75. docx @ 27 5574 @ 2 @ 1

2.3

Sample Nameplate

Pos: 41 / Techn ische Dokument ation/ Hebetech nik/ - Arch iv -/ 49 Rad greifer -Hebebüh nen/0 001 Rad greifer-H ebeb ühne n A lle/I nhalt e/Inh alt: Typens ch ild -Mus ter RG-H BZ MAHA @ 24\mod_1309945137131_75.docx @ 1021484 @ @ 1

MOBILE COLUMN LIFT

Ser.No. / Date of Production: ***

Project: ***

Type: ***

Charging Voltage: ***

Operating Voltage: ***

Net weight per column: ***

Load capacity per column: ***

System of Protection: ***

WEEE Reg. No. ***

Pos: 42 /Techn ische Dokument ation/Alle Ger äte/Übersc hriften/ Überschrifte n 1.1/L/Über schrift 1.1: Lärmem ission @ 13\mod _12 36767 2720 78_75.d ocx @ 35 4579 @ 2 @ 1

2.4

Noise Emission

Pos: 43 / Techn ische Dokument ation/ Hebetech nik/ - Arch iv -/ 00 H eb etechni k - Alle/I nh alte/ I nha lt: S cha lldr uc kpe gel < 70 dB( A) @ 1 4\mod_1241593887290_75.docx @ 371013 @ @ 1

The sound pressure level is lower than 70 dB(A) in the working area of the operator.

Pos: 44 /----- Forma t -----/M AN UEL LER UM BRUC H Se i tenu mbr uch @ 0\m od_1134403577687_0.docx @ 1277 @ @ 1

BA491901-en

Pos: 45 /Techn ische Dokument ation/Alle Ger äte/Übersc hriften/ Überschrifte n 1/B/Überschr ift 1: Bedienu ng @ 6\mod_1174482271218_75.docx @ 76877 @ 1 @ 1

Operation

Pos: 46 / Techn ische Dokument ation/ Alle Ger äte/Über schr iften/ Überschri ften 1.1/E/ Übersc hrift 1.1 : Ersti nbetr iebnahme @ 10\m od_12 1993 33897 48_7 5.docx @ 24047 4 @ 2 @ 1

3.1

Initial Operation

Pos: 47 / Techn ische Dokument ation/ Hebetech nik/ COLUM NLI FT/ 491 201 MCL/ BA/ Inh alt : 49 12 I nfo - Ante nne MCL/R GB/RG A @ 11\mod_1227623203445_75.docx @ 275646 @ @ 1

Place the receiving antennae in an upright position before operating the columns.

Pos: 4 8 /Tec hn ische Dokum ent ation/ Heb etech nik/ COL UMNLIF T/4 91201 MCL/ BA/I nhalt : 49 12 A ntenn e MCL/ RGB/ RGA ( Bi ld) @ 35\mod_1393426944951_0.docx @ 1911555 @ @ 1

Pos: 49 /Techn ische Dokument ation/Alle Ger äte/Übersc hriften/ Überschrifte n 1.1/H/Übers chrift 1 .1: Haup tschal ter @ 6\mod_ 117 75928 58312_ 75.do cx @ 906 35 @ 2 @ 1

3.2

Main Switch

Pos: 50 / Techn ische Dokument ation/ Hebetech nik/ - Arch iv -/ 00 H eb etechni k - Alle/I nh alte/ I nha lt: H aup tsc ha lter m it Not -Aus-Fu nktion HBZ @ 22\mod_1295874475528_75.docx @ 964591 @ @ 1

The main switch is used as emergency switch. In case of emergency turn it to position 0.

• Main switch in position 0: Power supply is interrupted

• Main switch in position 1: Lift is ready for operation

• When in position 0, the main switch can be protected against tampering

by means of a padlock.

Pos: 51 /----- Forma t -----/M AN UEL LER UM BRUC H Se i tenu mbr uch @ 0\m od_1134403577687_0.docx @ 1277 @ @ 1

BA491901-en

Pos: 52 /Techn ische Dokument ation/Alle Ger äte/Übersc hriften/ Überschrifte n 1.1/B/Über schrift 1.1: Bed ieneinheit @ 6\mod_1177424155343_75.docx @ 90114 @ 2 @ 1

3.3

Control Unit

Pos: 5 3 /Tec hn ische Dokum ent ation/ Heb etech nik/ COL UMNLIF T/4 91201 MCL/ BA/I nhalt : 49 12 B ediene inhei t ( Text) M CL/ RGB/ RGA @ 23\mod_1300266811654_75.docx @ 985943 @ @ 1

A LED Display: Operating Status

Red, yellow and green LEDs indicate the operating status. See also section "Troubleshooting".

B Button: Raise

When button is pushed, lift raises until button is released or upper end position is reached.

C Button: Lower

When button is pushed, lift lowers until button is released or lower end position is reached.

D LED Display: Number of Columns

Number of LEDs represents number of columns in a column unit. Flashing LED indicates next

free column number in an open column unit.

E Button: Open/Close Column Unit

Use this button to open a closed column unit or to close an open unit.

F LED Display: Column Unit

LED lighting up indicates that the column unit is closed. LED also lights up when operating

mode is changed (see below).

G LED Display: Channel Number

LED lighting up indicates current channel number.

H Button: Select Channel Number

Use this button to switch on to the next available channel. Occupied channels are skipped,

channel 10 is followed by channel 1 and so on.

I LED Display: Operating Mode

Current operating mode is indicated by LED.

J Button: Select Operating Mode

Use this button to switch on to the next mode. "Single" (one column), "Auto" (all columns of a

column unit) and "Group" (several columns) can be selected.

Pos: 54 /----- Forma t-----/ MAN UEL LE R UM BR UCH S ei ten umb ruch @ 0\mod_1134403577687_0.docx @ 1277 @ @ 1

BA491901-en

Pos: 5 5 /Tec hn ische Dokum ent ation/ Heb etech nik/ COL UMNLIF T/4 91201 MCL/ BA/I nhalt : 49 12 B ediene inhei t ( Bild) M CL/ RGB/ RGA @ 12\mod_ 123 14878 90433_ 0.docx @ 3006 30 @ @ 1

Pos: 56 /----- Forma t -----/M AN UEL LER UM BRUC H Se i tenu mbr uch @ 0\m od_1134403577687_0.docx @ 1277 @ @ 1

BA491901-en

Pos: 57 / Techn ische Dokument ation/ Alle Ger äte/Über schr iften/ Überschri ften 1.1/H/ Überschr ift 1 .1: Hubsä ulen aufste llen, anm eld en und ver bi nden @ 6\mod_1178277124484_75.docx @ 91204 @ 2 @ 1

3.4

Positioning, Logging in and Interconnecting the Columns

Pos: 5 8 /Tec hn ische Dokum ent ation/ Heb etech nik/ COL UMNLIF T/4 91201 MCL/ BA/I nhalt : 49 12 Hub sä ulen aufste llen, anm elde n und verbi nden @ 6\mod_1178277345406_75.docx @ 91217 @ @ 1

1 Push the support forks completely under the wheels or lift points of the vehicle to be raised.

Use the lift on a hard, level surface only.

2 Connect all columns to be used with the power supply.

It is possible to plug in either each column separately or a combination of not more than four col-

umns.

3 Turn the main switch to position 1.

 LED "Auto" flashes.

4 Select the transmission channel. All columns

belonging to the same unit must be set to

the same channel.

5 Confirm using the operating mode button.

 LED "Auto" lights up permanently.

6 Repeat the procedure for all columns.

 Number of columns within the unit is displayed.

Before closing the unit check the number of logged-in columns. After closing verify that it corre-

sponds with the number of columns appearing on the display.

7 Once all columns are logged in, close the unit using button

"0/1".

 LED "Column unit" lights up, lift is ready for operation.

Pos: 59 / Techn ische Dokument ation/ Alle Ger äte/Über schr iften/ Überschri ften 1.1/U/ Überschri ft 1. 1: Ums chalten auf Gr oup-M odus @ 6\m od_1178523038671_75.docx @ 91263 @ 2 @ 1

BA491901-en

3.5

Switching over to Group Mode

Pos: 60 / Tec hnis che Dok ument atio n/Heb etec hnik /COL UMNLI FT/4 912 01 MC L/BA/I nha lt: 4912 Umsch alten auf Gro up-Mod us M CL/ RGB @ 14\mod_1240917882212_75.docx @ 368047 @ @ 1

1 Switch to Group mode using the operating

mode button on the desired columns.

 LED "Group" lights up permanently.

Pos: 61 / Techn ische Dokument ation/ Alle Ger äte/Über schr iften/ Überschri ften 1.1/U/ Überschri ft 1. 1: Ums chalten auf S ingle-M odus @ 6\m od_1178526273265_75.docx @ 91290 @ 2 @ 1

3.6

Switching over to Single Mode

Pos: 62 / Techn ische Dokument ation/ Hebetech nik/ COLUMN LIFT/4 91201 M CL/BA/I nhalt : 4912 Umsch alten au f Sin gle-Mod us MC L/RG B @ 14\mod_1240919500168_75.docx @ 368074 @ @ 1

1 Switch to Single mode using the operating

mode button on the desired column.

 LED "Single" lights up permanently.

Pos: 63 / Techn ische Dokument ation/ Alle Ger äte/Über schr iften/ Überschri ften 1.1/H/ Überschr ift 1 .1: Hebe n und Se nke n @ 6\mod_1178521944593_75.docx @ 91237 @ 2 @ 1

3.7

Raising and Lowering

Pos: 6 4 /Tec hn ische Dokum ent ation/ Heb etech nik/ COL UMNLIF T/4 91201 MCL/ BA/I nhalt : 49 12 Heb en u nd S enke n MC L/RG B/RGA @ 2 2\mod_1293006318971_75.docx @ 959702 @ @ 1

• Before operating the lift, check that the number of

columns appearing on the display corresponds to the

number of columns actually logged in.

• All columns belonging to the same unit must be set

to the same channel.

• If the unit is opened there may be interference prob-

lems with other transmission channels.

• When operating the lift in Single or Group mode,

make sure the vehicle is not tilted. Otherwise the ve-

hicle may fall off the lift!

1 Press "Raise" or "Lower" button.

 Lift stops once button is released or end position is reached.

Pos: 65 /----- Forma t -----/M AN UEL LER UM BRUC H Se i tenu mbr uch @ 0\m od_1134403577687_0.docx @ 1277 @ @ 1

BA491901-en

Pos: 66 /Techn ische Dokument ation/Alle Ger äte/Übersc hriften/ Überschrifte n 1.1/A/Übersc hrift 1.1: Auss chalte n @ 15\mod_1245314486547_75.docx @ 390887 @ 2 @ 1

3.8

Shutdown

Pos: 6 7 /Tec hn ische Dokum ent ation/ Heb etech nik/ COL UMNLIF T/4 91201 MCL/ BA/I nhalt : 49 12 A ussch alten MCL/ RGB/ RGA @ 15\m od_1245314693378_75.docx @ 390939 @ @ 1

1 Before shutting down the lift, open the col-

umn unit using button "0/1".

 LED "Column unit" goes off.

2 Turn main switch to position 0.

Pos: 68 / Techn ische Dokument ation/ Alle Ger äte/Über schr iften/ Überschri ften 1.1/N/ Überschr ift 1 .1: Notab -Funktion, mechanisch @ 15\mod_ 124 52509 2128 6_75.d ocx @ 390 749 @ 2 @ 1

3.9

Emergency-down Function, Mechanical

Pos: 69 / Techn ische Dokument ation/ Hebetech nik/ - Arch iv -/ 00 H eb etechni k - Alle/Inhalte/Warnung!/Inhalt: Warnung - Manuell es Abs enke n nur dur ch g eschu ltes Pers onal @ 6\mod_1180962217687_75.docx @ 95217 @ @ 1

Authorized personnel only! Do not restart the lift before the error has been remedied.

Pos: 70 / Techn ische Dokument ation/ Papier korb/H ebetech nik/Inha lt: Ma nuelles Ab senk en RGE /RGA @ 24\m od_1310108278807_75.docx @ 1022148 @ @ 1

In case of power failure or defects the lift can be lowered manually.

Once the locking device is in engagement, manual lowering is no longer possible.

The following components are required for manual lowering:

A Lever at brake motor B Locking device

1 Pull or shake the safety wedge downward on each column.

2 First push onto the latch using a long screw driver, then additionally push the manual release

lever (in arrow direction).

Intermittently lower the columns in increments of approx. 50 mm (2 in), until the lift is in bottom

position.

Pos: 71 / Techn ische Dokument ation/ Hebetech nik/ COLUMN LIFT/4 90801 RGE /BA/ Inhalt: 4908 Ma nuel les Abs enken RGE/ RGA (Bild er) @ 42\mod_1433145052043_0.docx @ 2249463 @ @ 1

Pos: 72 /----- Forma t -----/M AN UEL LER UM BRUC H Se i tenu mbr uch @ 0\m od_1134403577687_0.docx @ 1277 @ @ 1

1 2

BA491901-en

Pos: 73 / Techn ische Dokument ation/ Alle Ger äte/Über schr iften/ Übers chri ften 1.1/T/ Über schri ft 1. 1: Tr ans port / Ver schieb en v on H ubs äule n @ 12\mod_1231486358029_75.docx @ 300405 @ 2 @ 1

3.10

Handling / Moving the Columns

Pos: 74 / Techn ische Dokument ation/ Hebetech nik/ COLUMN LIFT/4 90801 RGE /BA/ Inhalt: 4908 Transp ort/Ver schiebe n (Bi lder) @ 1 2\mod_1231486938020_0.docx @ 300505 @ @ 1

Pos: 75 /Techn ische Dokument ation/Papi erkorb/H ebetechnik/In halt: Transp ort/Vers chieben (Text) RGE @ 1 2\mod_1231486726149_75.docx @ 300480 @ @ 1

Screw a lifting-eye bolt M16 into the tap hole on the motor plate of the column. Insert a chain or

strap through the ring and lift the column using a hoist or forklift.

Close hydraulic valve by putting valve lever in position 3.

Pump with handle to raise the moving gear. Move column to desired position.

To lower the moving gear, open the hydraulic valve by putting the valve lever in position 1. The col-

umn is ready for operation.

Position 2 is the neutral position.

Pos: 76 /----- Forma t -----/M AN UEL LER UM BRUC H Se i tenu mbr uch @ 0\mod_1134403577687_0.docx @ 1277 @ @ 1

BA491901-en

Pos: 77 /Techn ische Dokument ation/Alle Ger äte/Übersc hriften/ Überschrifte n 1.1/A/Übersc hrift 1.1: Auf nahmetravers e für Sattelauf lieger @ 6\mod_1178182588031_75.docx @ 91050 @ 2 @ 1

3.11

Transverse Beam for Semitrailers

Pos: 78 / Techn ische Dokument ation/ Hebetech nik/ - Arch iv -/ 49 Rad greifer -Hebebüh nen/0 001 Rad greifer-H ebeb ühnen A lle/Inha lte/Inh alt: A ufnahm etravers e für S attel auflieger (Bilder ) @ 15\mod _1243 9544 31770_ 0.d ocx @ 385 024 @ @ 1

Pos: 79 / Techn ische Dokument ation/ Hebetech nik/ - Arch iv -/ 49 Rad greifer -Hebebüh nen/0 001 Rad greifer-H ebeb ühnen A lle/Inha lte/Inh alt: A ufnahm etravers e für S attel auflieger (Text) @ 1 5\mod_1243954387004_75.docx @ 384993 @ @ 1

A Support plate with location hole for central pivot of semitrailer

B Lift points for support forks

1 Position transverse beam under central pivot (C) of semitrailer.

2 Lower semitrailer until central pivot is approx. 20 mm above support plate (A).

Do not load the rollers of the transverse beam with the weight of the semitrailer.

3 Check for alignment of central pivot and location hole. Adjust if required.

4 Position the columns.

5 Raise the semitrailer being sure the central pivot engages the location hole.

Pos: 80 /----- Forma t -----/M AN UEL LER UM BRUC H Se i tenu mbr uch @ 0\m od_1134403577687_0.docx @ 1277 @ @ 1

BA491901-en

Pos: 81 / Techn ische Dokument ation/ Papier korb/Über schr iften/ Überschrif t 1: I nstandh altung @ 11\m od_12 3131 87366 29_7 5.docx @ 28955 0 @ 1 @ 1

Maintenance

Pos: 82 / Techn ische Dokument ation/ Alle Ger äte/I nhalte/W arnung!/ Inha lt: War nung - H aupts cha lter aus b ei Ins tand hal tung @ 14\mod_1240239070975_75.docx @ 362949 @ @ 1

Danger! Electric shock hazard!

Before doing any maintenance work, turn off the main switch and protect it against tampering.

Pos: 83 /Techn ische Dokument ation/Papi erkorb/Über schriften/ Überschrif t 1.1: Jährliche Überprüfun g @ 6\mod_11 74482 24571 8_75. docx @ 76 817 @ 2 @ 1

4.1

Annual Inspection

Pos: 84 / Techn ische Dokument ation/ Alle Ger äte/I nhalte/I nfo!/Inh alt: I nfo - J ährlic he Üb erp rüfu ng @ 1 4\mod_1242051457491_75.docx @ 373548 @ @ 1

• The maintenance interval prescribed by the manufacturer is

12 (twelve) months

This maintenance interval refers to normal workshop usage. If the equipment is used more fre-

quently or under severe operating conditions (e.g. outdoors), the interval must be reduced ac-

cordingly.

• Maintenance work shall be done only by authorized and trained service technicians provided by

the manufacturer, licensed dealers or service partners.

• In case of non-compliance the manufacturer's warranty becomes void.

Pos: 85 / Techn ische Dokument ation/ Hebetech nik/ - Arch iv -/ 00 H eb etechni k - Alle/In halte/ Info! /In halt : Inf o - DG UV R ege l 10 0-500 / DGUV Grundsatz 308-00 3 @ 47\mod_1484557193623_75.docx @ 2810767 @ @ 1

Pos: 86 / Techn ische Dokument ation/ Alle Ger äte/Über schr iften/ Überschri ften 1.1/P/Über schr ift 1. 1: Pfle gehinwe ise @ 15\mod _124 59122 34854_ 75.d ocx @ 39 5780 @ 2 @ 1

4.2

Care Instructions

Pos: 87 / Tec hnis che Dokum entation/ Alle Geräte/I nhalte/Inhal t: Pflegehinw eise - Alle Ger äte @ 24\mod_1303909841314_75.docx @ 999500 @ @ 1

• Periodically clean the equipment and treat it with a care product.

• Repair damage to the paintwork immediately to prevent corrosion.

• Usage of caustic cleaning agents or high pressure and steam jet cleaners may lead to equip-

ment damage.

Pos: 88 / Techn ische Dokument ation/ Alle Ger äte/I nhalte/I nfo!/Inh alt: I nfo - Pflegehinweise @ 24\mod_1304338389761_75.docx @ 1002352 @ @ 1

Regular care and maintenance is the key condition for functionality and long life expectancy of the

equipment!

Pos: 89 /Techn ische Dokument ation/Alle Ger äte/Übersc hriften/ Überschrifte n 1.1/SCH/Über schrift 1.1 : Schmierung @ 34\mod_1379919006147_75.docx @ 1830969 @ 2 @ 1

4.3

Lubrication

Pos: 90 / Techn ische Dokument ation/ Alle Ger äte/Über schr iften/ Überschri ften 1.1.1/SC H/Über schr ift 1.1.1: Schmi ermit tel @ 3 4\mod_1379919730255_75.docx @ 1831057 @ 3 @ 1

4.3.1

Lubricants

Pos: 91 / Techn ische Dokument ation/ Hebetech nik/ COLUMN LIFT/4 90801 RG E/B A/Inh alt: 490 8 Warn ung - Kein Fe tt mi t Fes tsc hmie rsto ffa nteil RGE/ RGA @ 3 5\mod_1390294548421_75.docx @ 1876598 @ @ 1

For lubrication use a mineral-oil based grease which is suitable for rolling bearings.

Do not use greases containing solid lubricants (such as graphite or MoS2.).

Pos: 92 /----- Forma t -----/M AN UEL LER UM BRUC H Se i tenu mbr uch @ 0\m od_1134403577687_0.docx @ 1277 @ @ 1

BA491901-en

Pos: 93 /Techn ische Dokument ation/Alle Ger äte/Übersc hriften/ Überschrifte n 1.1.1/K/Üb erschrift 1. 1.1: Kugelumlaufm utter @ 14\mod_1241506892227_75.docx @ 370083 @ 2 @ 1

4.3.2

Recirculating Ball Nut

Pos: 94 / Techn ische Dokument ation/ Hebetech nik/ - Arch iv -/ 49 Rad greifer -Hebebüh nen/0 001 Rad greifer-H ebeb ühnen A lle/Inha lte/Inh alt: I nst. dur ch den Betreib er - K ugel umla ufmutt er RGE @ 8\mod_1203344483645_75.docx @ 147411 @ @ 1

Twice a year grease the recirculating ball nut with 4…7 strokes from a grease gun. The lubricator is

located at the recirculating ball nut inside the carriage.

To make the lubricator accessible, remove the

screws (1 and 3). Then remove cover plate (4)

and fastening strip of rubber cover (2).

Fold down the rubber cover.

Pos: 95 /----- Forma t-----/ MAN UEL LE R UM BR UCH S ei ten umb ruch @ 0\mod_1134403577687_0.docx @ 1277 @ @ 1