Sunjoy 110102071 User manual

Brand
Sunjoy
Model
110102071
Type
User manual

Sunjoy 110102071 is a 12 ft. x 12 ft. steel gazebo with a hardtop and mesh screening. It is designed to provide shade and protection from the elements, and it can be used for a variety of purposes, such as outdoor dining, entertaining, or relaxing. The gazebo is easy to assemble and disassemble, and it comes with all the necessary hardware and instructions.

Here are some of the key features of the Sunjoy 110102071 gazebo:

  • 12 ft. x 12 ft. size: The gazebo is large enough to accommodate a table and chairs, or a small group of people.
  • Steel frame: The gazebo is made of durable steel, which is resistant to rust and corrosion.

Sunjoy 110102071 is a 12 ft. x 12 ft. steel gazebo with a hardtop and mesh screening. It is designed to provide shade and protection from the elements, and it can be used for a variety of purposes, such as outdoor dining, entertaining, or relaxing. The gazebo is easy to assemble and disassemble, and it comes with all the necessary hardware and instructions.

Here are some of the key features of the Sunjoy 110102071 gazebo:

  • 12 ft. x 12 ft. size: The gazebo is large enough to accommodate a table and chairs, or a small group of people.
  • Steel frame: The gazebo is made of durable steel, which is resistant to rust and corrosion.
ASSEMBLY INSTRUCTION
Item#:L-GZ636PST-B
SAFETY INFORMATION
Please read and understand this entire manual before attempting to assemble, operate or
install the product.
WARNING
This product is intended for outdoor use only and should be placed on flat, horizontal
ground.
Ensure enough clearance around the product.
Anchor the gazebo to the ground with stakes for added safety. Stakes are provided to
secure the gazebo in the ground. If you wish to secure the gazebo to a concrete and
wood surfaces, use anchors suited for these surfaces (anchors not included).
Do not assemble the gazebo on sandy, muddy or loose soil, as stakes do not have
enough anchorage in these types of soil.
Before assembling the product, find level ground no less than 6 ft. away from any
structures or obstructions, such as fences, garages, houses, overhanging branches,
laundry lines, or electrical wires.
CAUTION
Any assembly or maintenance of the product must be carried out by adults only.
Six or more people are recommended to safely assemble and/or move the product.
Some parts may contain sharp edges. Wear protective gloves if necessary.
Check all nuts and bolts periodically for tightness. When required, tighten them again.
Do not hang any weights on the roof frame.
Always keep children under close supervision when they are using or are around this
product.
Never leave children unattended.
PREPARATION
Before beginning assembly of product, make sure all parts are present. Compare parts with
package contents list and hardware contents list. If any part is missing or damaged, do not
attempt to assemble the product.
Estimated Assembly Time: 90 minutes.
Tools Required for Assembly: Wrench (included) and Phillips Screwdriver (not included).
Parts List
Post
A
4
Top Screen 1
B
4
Top Screen 2
C
4
Big Top Slanting Bar
D
4
Big Top Beam
E
4
Big Top Slanting Bar
Connector
F
4
Big Top Beam Connector
G
4
Big Top Bar
H
4
Big Top Connector
I
4
Big Roof Top Beam 1 (left)
J1
4
Big Roof Top Beam 1
(right)
J2
4
Big Roof Top Beam 2 (left)
J3
4
Big Roof Top Beam 2
(right)
J4
4
Small Roof Top Beam
J5
4
Small Top Support Bar
K1
4
Big Top Left Support Bar
K2
4
Big Top Right Support Bar
K3
4
Small Top Slanting Bar
M
4
Hardware Pack 1
AA
M6*15 Bolt
BB
M6 Flat Washer
ZZ
M6 Wrench
Small Top Cover
O
1
Hook
P
1
Small Top Connector
Q
1
Small Top Roof Panel
R1
4
Big Top Roof Panel 1
R2
4
Big Top Roof Panel 2
R3
4
Small Top Cover 1
S1
4
Big Roof Panel Cover 1
S2
4
Big Roof Panel Cover 2
S3
4
Small Top Cover 2
T2
4
Big Roof Panel Cover 3
T3
4
Big Roof Panel Cover 4
T4
8
1. Insert the Top Screen 2
(C) into the Top Screen 1 (B),
and then install the Big Top
Beam Connector (G) onto
the screens and securing
with Bolts (AA) and Flat
Washers (BB).
2. Attach the Big Top Slanting
Bar Connector (F) to the Post
(A) with Bolts (AA) and Flat
Washers (BB).
3. Attach the assembled
screens (B、C) to the Post (A)
with Bolts (AA) and Flat
Washers (BB).
Hardware Pack 2
AA
M6*15 Bolt
BB
M6 Flat Washer
DD
M6*55 Screw
EE
M6 Nut
4. Insert the Big Top Bar (H)
into the Big Top Connector
(I) and securing with Bolts
(AA) and Flat Washers (BB).
5. Attach the Big Top Slanting
Bar (D) to the Big Top
Connector (I) with Bolts (AA)
and Flat Washers (BB).
6. Attach the Big Top Slanting
Bar (D) to the Big Top
Slanting Bar Connector (F)
with Screws (DD), Nuts (EE)
and Flat Washers (BB).
Hardware Pack 3
AA
M6*15 Bolt
BB
M6 Flat Washer
FF
M6*25 Screw
GG
M6*40 Screw
II
M6 Nut
9. Attach the Small Top Slanting Bar
(M) to the Small Top Connector (Q)
with Screws (DD), Nuts (EE) and
Flat Washers (BB). Then attach the
Hook (P) to the bottom center of the
Small Top Connector (Q) by
screwing it counterclockwise.
11. Attach the Small Roof
Top Beam (J5) to the Small
Top Slanting Bar (M) with
Bolts (AA) and Flat
Washers (BB).
12. Attach the Small Top Support
Bars (k1) to the Small Top Slanting
Bar (M) with Bolts (AA) and Flat
Washers (BB).
7. Attach the Big Top Beam
(E) to the Big Top Bar (H)
with Bolts (AA) and Flat
Washers (BB).
7. Attach the Big Top Beam
(E) to the Big Top Bar (H)
with Bolts (AA) and Flat
Washers (BB).
8. Attach the Big Top Beam
(E) to the Big Top Beam
Connector (G) with Screws
(DD) , Nuts (EE) and Flat
Washers (BB).
10. Attach the four pieces
of Small Top Slanting
Bars (M) to the Big Top
Bar (H) with Bolts (AA)
and Flat Washers (BB).
13. Put the Small Top Roof Panel
(R1) onto the small top and put
the Small Top Cover 2 (T2) onto
the Small Top Roof Panel (R1),
then attach both of them (R1 &
T2) to the Small Top Support Bar
(K1) with Screws (FF) and Flat
Washers (BB).
14. Attach the Small Top
Cover 1 (S1) to the Small
Top Slanting Bar (M) with
Screws (GG) and Flat
Washers (BB).
15. Attach the Small Top
Cover (O) to the Small Top
with Nut (II).
16. Attach the Big Roof Top Beam
1 (right) (J2) and the Big Roof Top
Beam 1 (left) (J1) to the Big Top
Slanting Bar (D) with Bolts (AA)
and Flat Washers (BB).
Repeat this procedure to the Big
Roof Top Beam 2 (right) (J4) and
the Big Roof Top Beam 2 (left) (J3)
17. Attach the Big Roof Top Beam
1 (left) (J1) and the Big Roof Top
Beam 1 (right) (J2) to the Big Top
Beam (E) with Bolts (AA) and Flat
Washers (BB).
Repeat this procedure to the Big
Roof Top Beam 2 (right) (J4) and
the Big Roof Top Beam 2 (left) (J3)
18. Attach the Big Top Left
Support Bar (K2) and the
Big Top Right Support Bar
(K3) to the Big Top Beam
(E) with Bolts (AA) and
Flat Washers (BB).
Hardware Pack 4
AA
M6*15 Bolt
BB
M6 Flat Washer
FF
M6*25 Screw
II
M6*20 Screw
GG
M6*40 Screw
HH
Ф 8*180 Stake
19. Attach the Big Top Left Support Bar
(K2) and the Big Top Right Support Bar
(K3) to the Big Top Slanting Bar (D) with
Bolts (AA) and Flat Washers (BB).
CARE AND MAINTENANCE
Check all nuts and bolts periodically for tightness. When required, tighten them again.
This gazebo is intended for decorative and sunshade purposes only, and is not
designed to withstand hard weather, including high winds, rain or snow. In order to
avoid damage, remove accumulated water on the roof immediately, or disassemble
the gazebo.
20. Put the Big Top Roof
Panel 1 (R2) and the Big Top
Roof Panel 2 (R3) onto the big
top, and then secure both of
them (R2 & R3) to the Big Top
Beam (E) with Screws (II) and
Flat Washers (BB).
21. Put the Big Roof Panel
Cover 4 (T4) onto the Big Top
Roof Panel 1 (R2) and the Big
Top Roof Panel 2 (R3), and then
secure all of them (T4 & R2 &
R3) to the Big Top Left Support
Bar (K2) and the Big Top Right
Support Bar (K3) with Screws
(FF) and Flat Washers (BB).
22. Put the Big Roof Panel
Cover 3 (T3) onto the Big
Top Roof Panel 1 (R2) and
the Big Top Roof Panel 2
(R3), and then secure the
Big Roof Panel Cover 3
(T3) to the Big Top Bar (H)
with Bolts (AA) and Flat
Washers (BB).
23. Attach the Big Roof Panel
Cover 1 (S2) to the Big Top
Slanting Bar (D) with Screws
(GG) and Flat Washers (BB).
Repeat this procedure to
attach the Big Roof Panel
Cover 2 (S3) to the Big Top
Beam (E).
24. Secure the gazebo with the
Stakes (HH) to the ground.
Always disassemble the gazebo completely. A partially disassembled gazebo is not
stable enough to resist wind and bad weather, and therefore can be damaged and/or
cause damage.
Do not use bleach, acid or other abrasive cleaners on the roof or frame parts.
Steel components of garden accessories and furniture are treated with rust-inhibiting
paint. However, due to the nature of steel, surface oxidation (rusting) will occur if this
protective coating is scratched. This is a natural process. To minimize this condition, it
is recommended care be taken when assembling and handling the product, in order to
prevent the paint from being scratched.
Surface rust can be removed easily using a very light application of common cooking
oil. If surface oxidation (rusting) occurs and no measures are taken to correct it, the
oxidation may start dripping onto the assembly surface, which may cause damaging
stains that may be difficult to remove.
If the product will not be used for a long period (e.g. winter time), it should be stored in
a clean, dry environment.
Keep the original packaging to store the gazebo.
LIMITED WARRANTY:
This limited warranty is extended to the original purchaser and applies to defects in
materials and workmanship of your item provided the item is maintained with care and
used only for personal, residential purposes. The item is warranted to be free from defects
in material or workmanship for a period of one (1) year. If any defect is found, please call
our customer service department at 1-866-578-6569 for help. The manufacturer will not
cover transportation or delivery costs, or compensate the individual or any outside party
for assembling or disassembling the product. This warranty gives you specific legal rights,
and you may also have other rights which vary from state to state.
EXCLUSIONS: Items used for commercial, contract, or other non-residential purposes, or
items damaged due to acts of nature, vandalism, misuse, or improper assembly are not
covered. Corrosion or rusting of hardware is not covered. Proof of purchase (dated
register receipt) is required for warranty claims. Warranty is to the original purchaser and
is non-transferable. Any replacement of warranted items will be in the original style and
color, or a similar style and color if the original is unavailable or has been discontinued. As
some states do not allow exclusions or limitations on an implied warranty, the above
exclusions and limitations may not apply. This warranty gives you specific rights, and you
may also have other rights, which vary from state to state.
Important: Please do not return this product to the store. For technical assistance on
assembly or replacement parts. Please call Sunjoy Industries at 1-866-578-6569 from
8:00 am EST to 8:00 pm PST or fax the replacement part form which is in the box to
1-740-283-3549 or Email customer.care@sunjoygroup.com for assistance.
Made in China
2016-4
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11

Sunjoy 110102071 User manual

Brand
Sunjoy
Model
110102071
Type
User manual

Sunjoy 110102071 is a 12 ft. x 12 ft. steel gazebo with a hardtop and mesh screening. It is designed to provide shade and protection from the elements, and it can be used for a variety of purposes, such as outdoor dining, entertaining, or relaxing. The gazebo is easy to assemble and disassemble, and it comes with all the necessary hardware and instructions.

Here are some of the key features of the Sunjoy 110102071 gazebo:

  • 12 ft. x 12 ft. size: The gazebo is large enough to accommodate a table and chairs, or a small group of people.
  • Steel frame: The gazebo is made of durable steel, which is resistant to rust and corrosion.
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents