Page is loading ...
Assembly Instructions
ltem:
Aluminum Hardtop Gazebo
Model: Victoria Pavilion
ZYG11-6
P1
ALUMINUM HARDTOP GAZEBO ASSEMBLY INSTRUCTION
Note:
THIS UNIT IS HEAVY! For safety, Do NOT assemble this item alone. six people are recommended
for a safe assembly. A screw driver, hammer, two ladders (not included) with height no less than
2.5m are needed to install. For ease of identification when installing, all parts are labeled. This
product takes at least two hours to set up. When unpacking the product, please discard the metal
, protecting frames included in the shipping cartons.
e part is used.
Step.3
Step.2
Step.4
Step.1
Step.5
A1 (x2)
Long right
decorative beam
B1 (x2)
Long left
decorative beam
C1 (x2)
Short right
decorative beam
D1 (x2)
Short left
decorative beam
E1 (x4)
Middle beam
connector
G1 (x4) Corner connector
A2 (x4) Top slanting bar
B2 (x2)
Middle beam of big
top long side
C2 (x2)
Middle beam of
big top short side
D2 (x2)
Left long support
beam of
big top
long side
E2 (x2)
Right long
support beam of
big top long side
F2 (x2)
Left short support
beam of big top
long side
G2 (x2)
Right short
support beam of
big top long side
H2 (x2)
Left long support
beam of
big top
short side
I2 (x2)
Right long
support beam of
big top short side
J2 (x2)
Left short support
beam of big top
short side
K2 (x2)
Right short
support beam of
big top short side
L2 (x2) Top long panel
M2 (x2) Top short panel
A3 (x2)
Bottom beam of
small top 1
A6 (x2)
Bottom beam of
small top 2
B3 (x4)
Upper beam of
small top
C3 (x2)
Roof cover of
small top long
side
D
3
(
x2
)
Roof
cover
of
small
top short side
E3 (x2)
Long side support
bar
F3 (x2)
Short side support
bar
G3 (x1)
Connector of
small top
H3 (x1)
Top cover of small
top
I3 (x1) Top decor A4 (x4) Post base
B4 (x4) Base protector C4 (x4) Post
D4 (x4) Top block
E4 (x4) Block plate
F4(x4) Arc support bar G4 (x4) Arc support bar
A5 (x2)
Left roof cover of
long side 1
B5 (x2)
Right roof cover of
long side 1
C5 (x2)
Left roof cover of
long side 2
D5 (x2)
Right roof cover of
long side 2
P2
ALUMINUM HARDTOP GAZEBO ASSEMBLY INSTRUCTION
P3
E5
(x2)
Left
roof
cover
of
long
side
3
F5
(x2)
Right
roof
cover
of
long
side
3
G5
(x2)
Roof
cover
of
short
side
1
H5
(x2)
Left
roof
cover
of
Short
side
2
I5 (x2)
Right
roof
cover
of
short
side
2
J5
(x2)
Left
roof
cover
of
Short
side
3
K5 (x2)
Right
roof
cover
of
short
side
3
L5
(x4)
Top
cover
M5
(x1)
Pothook N5 (x18) Roof press sheet
Hardware Pack
1
JJ
1/4" - 20×1.25
hex bolt
CC
1/4" -
20×0.6
hex bolt
8 PCS
36 PCS
28 PCS
2 PCS
Fig.1: Insert the decorative beam B1 (D1) into A1 (C1); fasten with bolts (CC) & flat washers (BB).
Fig.2: Connect assembled beams, fasten with bolts (JJ) & flat washers (BB).
Fig.3: Attach the Middle beam connector E1 to the decorative beams with bolts (CC) & flat washers (BB).
Fig.4: Attach the Corner connector (G1) to the corner of the decorative beams with bolts (CC) & flat washers (BB).
Long
netting
bar
O1(x4)
Short
netting
bar
O2
(x4)
Wall
P2(x1)
P1(x1)
ALUMINUM HARDTOP GAZEBO ASSEMBLY INSTRUCTION
P3(x104)
Mosquito netting hook
Mosquito netting
AA 1/4" - 20×1 hex bolt
8 PCS
72 PCS
16 PCS
32 PCS
16 PCS
16 PCS
CC 1/4" - 20×0.6 hex bolt
DD 1/4" - 20×0.6 bolt
EE 1/4" - 20×2.125 bolt
FF 1/4" - 20 hexagon nut
Hardware Pack 2
Fig.5: Attach the Top short panel (M2) to the Top long panel (L2) with bolts (AA) & washers (BB).
Fig.6: Attach the Top slanting bar (A2) to the Corner connector (G1) with bolts (EE) & washers (BB) & nuts (FF).
Fig.7: Attach the Top slanting bar (A2) to the assembled small top frame with bolts (CC) & washers (BB).
Fig.8: Attach the Middle beam of big top B2 (C2) to the assembled Middle beam connector E1 with bolts (EE),
washers (BB) and nuts (FF).
Fig.8-1: Connect the Middle beam of big top C2 and the assembled small top frame M2with bolts (CC)&washers (BB).
Fig.8-2: Attach the Middle beam of big top B2 to the assembled small top frameL2 with bolts (CC) & washers (BB).
Fig.9: Connect one end of the L
eft long support beam of big top long side (D2) and the Middle beam of big top (B2),
fasten with bolt (DD) & washer (BB).
Fig.10:
Attach the other end of the long support beam (D2) to the Top
slanting bar (A2) with bolts (DD) & washers (BB
Use the same way to assemble E2, F2, G2, H2, I2, J2, and K2respectively.
P4
ALUMINUM HARDTOP GAZEBO ASSEMBLY INSTRUCTION
BB
AA
Fig.11: Insert the Long side support bar (E3) & short side support bar (F3) into the corner pipe of bottom beam of
small top (A3 & A6) as indicated in the figure.
Fig.12: Attach the assembled small top frame to the assembled big top frame as displayed in the figure.
Fig.13: Attach the Connector of small
top (G3) to the Bottom beam of small top (A3 & A6) with bolts (DD) and
washers (BB); then attach the p
othook (M5) to the connector of small top (G3).
Fig.14:
beam of small top (B3) on the Bottom beam of small top (A3 & A6), and fasten with nuts (KK) & washers (BB). Put
the Top cover of small top (H3) on the Connector of small top (G3), then screw the Top decor (I3) on it.
Hardware Pack 4
CC 1/4" - 20×0.6 bolt 72 PCS
DD 1/4" - 20×0.6 bolt 24 PCS
P5
Hardware Pack 3
DD 1/4" - 20×0.6 bolt 4 PCS
KK
1/4" -20 hexagonal capped
nut
8 PCS
ALUMINUM HARDTOP GAZEBO ASSEMBLY INSTRUCTION
Place the Roof cover of small top (C3 & D3) on the bottom beam of small top place the Upper(A3 & A6);
Fig.15: Lift the Base protector (B4), attach the post base (A4) to the post (C4) with bolts (DD) & washers (BB).
Fig.16: Attach the top block (D4) to the post (C4) with bolts (CC) & washers (BB). (Note: the
screw holes
on the post and the screw holds for installing the block plate (E4) should be in the same direction as
shown in the figure)
Fig.17: Lift the
assembled pavilion roof and attach the assembled posts to the corners of the roof with bolts
(CC) & washers (BB). (Note: The screw holes on the post must be directed inward. 6 people are needed here.)
Fig.18: Attach the Corner connector (G1) to the top block (D4) with bolts (CC) & washers (BB).
Fig.19: Attach the block plate (E4) to the top block (D4) with bolts (DD) & washers (BB).
Fig.20: Attach the arc support bar (F4/G4) to the post (C4) & decorative beam with bolts (CC) & washers (BB).
Fig.21: If placing the gazebo on soft ground, use ground stakes (HH) for added stability.
Fig.21-1: If placing the gazebo on the cement ground, fasten with concrete anchor
s (II).
P6
ALUMINUM HARDTOP GAZEBO ASSEMBLY INSTRUCTION
Fig.15
B4
A4
B4
A4
C4
G4
D4
Fig.20
F4
G4
D4
C4
C4
Fig.21 Fig.21-1
F4
Fig.16
Fig.17
D4
Fig.18
Fig.19
Hardware Pack 5
Fig.22: Press the left roof cover of long side 1 (A5) onto the right roof cover of long side 1 (B5) as shown in
Fig. 22, and insert into the U groove of B2 at the same time, as shown in Fig. 22-1
Fig.23: Install the roof cover of short side
1 (G5) & left roof cover of long side 1 (A5) on the top slanting
bar (A2) with bolts (DD) & washers (BB).
DD 1/4" - 20×0.6 bolt 58 PCS
GG 1/4" - 20×1.6 bolt 8 PCS
P7
ALUMINUM HARDTOP GAZEBO ASSEMBLY INSTRUCTION
5
Fig.26
66PCS
IMPORTANT:
1.
Keep
all
children
and
pets
away
from
assembly
area.
Children
and
pets
should
be
supervised
when
they
are
in
the
area
of
pavilion
construction.
2.
The
area
for
assembly
should
not
be
less
than
6
feet
from
any
obstruction
such
as
fence,
garage,
house,
overhanging
branches,
laundry
line
or
electrical
wires.
3.
This
unit
is
heavy.
Do
not
assemble
this
item
alone,
six people
are
recommended
for
safe
assembly.
4.
Some
parts
may
contain
sharp
edges.
Wear
protective
gloves
if
necessary
during
assembly.
5.
When
assembling
and
using
this
product,
basic
safety
precautions
should
always
be
followed
to
reduce
the
risk
of
personal
injury
and
damage
to
equipment.
Please
read
all
instructions
before
assembly
and
use.
6.
For
outdoor
use
only.
Install
on
level
ground.
16
stakes
are
provided
to
secure
the
pavilion
in
the
ground.
If
you
wish
to
secure
the
pavilion
to
a
wood
deck
surface,
you
will
need
to
purchase
fasteners
appropriate
for
these
surfaces.
These
are
readily
available
at
your
local
hardware
store
or
home
center.
7.
Check
all
bolts
for
tightness
before
and
during
usage.
8. Please check your state and local
regulations
prior
to
purchasing. Some
jurisdictions
may
require
permits
for,
or
otherwise
regulate,
installation
and
use.
9.
While
this
pavilion
is
manufactured
to
withstand
gale
force
winds
utilizing
only
the
supplied
ground
stakes,
in
areas
subject
to
frequent
severe
weather,
securing
the
pavilion
to
a
deck,
concrete
patio
or
footings
should
be
considered.
10.
Your
pavilion
has
been
engineered
to
accommodate
winter
snow
loads
incurred
in
most
areas.
Removal
of
accumulated
snow
on
the
pavilion
roof
with
a
roof
rake
is
recommended.
In
areas
that
are
regularly
subject
to
blizzard
conditions
however,
removal
of
the
roof
panel
is
suggested.
The
assembled
roof
structure
can
simply
be
left
intact
until
warmer
conditions
return.
Fig.24: Attach
the
roof
covers
C5,
D5,
E5,
F5,
H5,
I5,
J5,
K5
to
the
top
slanting
bar
(A2)
with
bolts
(DD)
&
washers
(BB).
Fig.25: Press
up
the
roof
cover
with
the
roof
press
sheet
(N5),
and
fix
N5
on
the
decorative
beam
with
bolt
(DD)
&
washer
(BB).
Fig.26: Insert
the
top
cover
(L5)
into
the
hole
of
the
small
top
frame
corner.
Fix
the
top
cover
(L5)
on
the
top
slanting
bar
(A2)
with
bolts
(GG)
&
wash
ers
(BB).
P8
ALUMINUM HARDTOP GAZEBO ASSEMBLY INSTRUCTION
Now, your Sunoma Pavilion is ready for use.
Fig.28
Fig.29
Fig.27:
Fig.28: :
DD
DD
DD
DD
BB
BB
BB
BB
Fix the netting bar O1( O2) to the decorative
washer (BB).
beam A1,B1(C1,D1) by usin
g bolt (DD) and flat
A1(C1)
B1(D1)
O1(O2)
O1(O2)
Fig.29
Hang Mosquito netting (P1) on the inside
netting bar
(O1 &O2) by using the
pipe of
on the outside pipe in the same way.
Mosquito netting hook (P3), hang the Wall (P2)
P1
P1
P2
P2
Fig.29
-1
&
Fig.29
-1
:
P3
O1(O2)
P2
P1
P9
ALUMINUM HARDTOP GAZEBO ASSEMBLY INSTRUCTION
CUSTOMER SERVICE
Zenith Industries, LCC warrants to the original purchaser that this item is free from defects in work-
manship and materials of your item provided the item was factory-sealed at the time of purchase and
is maintained with care and used only for personal, residential purposes. The item is warranted to be
free from defects in material or workmanship for a period of 1 year. Should any manufacturing
defect arise within this warranty period, Zenith Industries, LLC will repair or replace (at our option)
any defective merchandise upon proof of purchase receipt with date at no charge to the customers for
replace parts and labor; however, transportation and delivery costs, remain the responsibility of the
purchaser. A purchaser of an "open box," previously-returned, or "clearance" item, as well as original
purchasers outside of the warranty period, may obtain replacement parts from Zenith Industries for
products in current production, at nominal cost.
If you are within the return policy that most stores have, you do have the option of returning this item
back to the store which you bought it from for an exchange of the same item, or a refund of the
purchase.
If you are within or beyond the return policy that most stores have, and need tech. assistance or
replacement parts, please call Zenith Industries, LLC at 1(855)-6-ZENITH from 9:30 am to 6:30 pm
form together with the purchase receipt to 1 (513) 217-9415 for assistance.
CARE & Maintenance
Our steel components for garden accessories and furniture are treated with rust inhibiting paint that protects it from
rusting. However, due to the nature of steel, surface oxidation (rusting) will occur once these protective coatings
are scratched. This is a natural process
and is not a defect! To minimize this condition, we recommend care when
assembling & handling the product to prevent scratching the paint. Should any scratching or damage occur, we
Surface rust can also
recommend immediate touch-up with rust inhibiting paint.
be easily removed with a very light
application of common cooking oil. If surface oxidation (rusting) occurs and if no
measure is taken to prevent this,
the oxidation may start dripping on to deck or patio and caused damaging stains,
which may be difficult to remove.
This can be prevented if the measure is taken to keep the product from oxidizing.
/
