Sunjoy 110101057 User manual

Brand
Sunjoy
Model
110101057
Type
User manual
1 / 8
Assembly Instructions
Item#:D-GZ941PST
2 / 8
Before beginning assembly of product, make sure all parts are present. Compare parts with package contents list.
If any part is missing or damaged, do not attempt to assemble the product.
Preparation:
Our clear, easy-to-follow, step-by-step instructions will guide you through the project from start to finish. The
final product will be a quality piece that will go together smoothly and give years of enjoyment.
1. Keep all children and pets away from assembly area. Children and pets should be supervised when they are in
the area of gazebo construction.
Important:
2. The area for assembly should not be less than 6 feet from any obstruction such as fence, garage, house,
overhanging branches, laundry line or electrical wires.
3. This unit is heavy. Do not assemble this item alone. Six people are recommended for safe assembly.
4. Some parts may contain sharp edges. Wear protective gloves if necessary during assembly.
5. When assembling and using this product, basic safety precautions should always be followed to reduce the risk
of personal injury and damage to equipment. Please read all instructions before assembly and use.
6. For outdoor use only. Install on level ground. Stakes are provided to secure the gazebo in grass ground. If you
wish to secure the gazebo to a wood deck or concrete surface, you will need to purchase fasteners appropriate for
these surfaces. These are readily available at your local hardware store or home center.
7. Check all bolts for tightness before and during usage.
8. While this gazebo is manufactured to withstand gale force winds utilizing only the supplied ground stakes, in
areas subject to frequent severe weather, securing the gazebo to a deck, concrete patio or footings should be
considered.
3 / 8
Small top connector
A 1
Slanting bar of small top B 4
Large top connector
C 1
Middle beam D 4
Slanting bar E 4
Middle beam connector F 4
Slanting bar connector G 4
Base cover H 4
Post I 4
Long beam J 4
Short beam K 4
Lower slanting bar L 4
Lower middle beam M 4
Decorative plate N 4
Baffle P 4
Mosquito netting bar Q 8
Hook R 1
Parts List
4 / 8
AA M6*20 Bolt 88 PCS
BB M6 Washer 88 PCS
CC M6 Nut 8PCS
W M6 Wrench 2 PC
Hardware Pack 1
Small canopy
U
1
Largo canopy1
S
1
Largo canopy 2
T
1
5 / 8
HH M6*35 Cross-head bolt 8 PCS
BB M6 Washer 16 PCS
CC M6 Nut 8 PCS
Hardware Pack 2
Fig.1: Put the base cover（H）on the lower end of Post（I）then fix them by using Bolt (AA) and Washer (BB).
Fig.2:Assemble the Long beam (J) and Short beam(K) by using Bolt (AA) , Washer(BB) and Nut（CC）.
Fig.3:Attach the Middle beam connector (F) to the assembled beam J&K by using Bolt(AA）and Washer
（BB）.
Fig.4
：
Attach the Decorative plate（N）to the assembled beam J&K by using Bolt(AA）and Washer（BB）.
Fig.5: Attach the Slanting bar connector (G) to the Post (I) by using Bolt (AA) and Washer (BB).
Fig.6: Attach the assembled beam J&K to the Post (I) by using Bolt(AA）and Washer（BB）.
Fig.7: Attach the Mosquito netting bar (Q) to the assembled beam J&K by using Bolt (AA) and Washer(BB).
Fig.8Attach the Baffle（P）to the Post (I) by using Bolt (AA) and Washer(BB).
6 / 8
Fig.9: Attach the Slanting bar of small top (B) to the small top connector (A).
Fig.10: Attach the assembled small top to the Large top connector (E) by insert the tube of Slanting
bar of small top (B) into the tube of Large top connector (E).
Fig.11: Lay the small canopy (P) on the small top, and secure it on four corners of Slanting bar of
small top (B).
Fig.9: Insert the Slanting bar (E) into the Lower slanting bar（L）.
Fig.10: Insert the upper end of the Slanting bar (E) into the tube of Large top connector, meanwhile
screw the Hook（R）into the Large top connector（C）.
Fig.11:Attach the lower slanting bar（L）into the slanting bar connector (G) by using Bolt（HH），
Washer（BB）and Nut（CC）.
Fig.12: Insert the Middle beam (D) into the Lower middle beam（M）.
Fig.13: Insert the Middle beam (D) into the tube of Large top connector（C）.
Fig.14: Attach the Lower middle beam（M）to the Middle beam connector (F) by using Bolt（HH），
Washer (BB
）
and Nut
（
CC
）。
Lay the large canopy on the large top and do not spread it now.
7 / 8
This limited warranty is extended to the original purchaser and applies to defects in materials and workmanship of
your item provided the item is maintained with care and used only for personal, residential purposes. The item is
Limited Warranty:
Hardware Pack 3
EE Φ8*180 Stake 16 PCS
Fig.13 :Spread the Large canopy (T)，and secure it on four corners of Slanting bar (L).
Fig.14: Fix the gazebo on the ground by using Stake（EE）.
8 / 8
warranted to be free from defects in material or workmanship for a period of one 6 months. We don't reimburse
for transportation or delivery costs, or compensate the individual or any outside party for assembling or
disassembling the product.
Items used for commercial, contract, or other non-residential purposes, or items damaged due to acts of nature,
vandalism, misuse, or improper assembly are not covered. Corrosion or rusting of hardware is not covered. Proof
of purchase (dated register receipt) is required for warranty claims. Warrant it to the original purchaser and is
non-transferable. Any replacement of warranted items will be in the original style and color, or a similar style and
color if the original is unavailable or has been discontinued. As some states do not allow exclusions or limitations
on an implied warranty, the above exclusions and limitations may not apply. This warranty gives you specific
rights, and you may also have other rights, which vary from state to state.
Exclusions:
Our iron/steel components for garden accessories and patio items are coated with rust inhibiting paint that protects
it from rusting. However, due to the nature of iron, surface oxidation (rusting) will occur once these protective
coatings are scratched. This is a natural process and is not a defect! To minimize this condition, we recommend
care when assembling & handling the product to prevent scratching the paint. Should any scratching or damage
occur, we recommend immediate touch-up with rust inhibiting paint. Surface rust can also be easily removed with
a very light application of common cooking oil. If surface oxidation (rusting) occurs and if no measure is taken to
prevent this, the oxidation may start dripping on to deck or patio and cause damaging stains, which may be
difficult to remove. This can be prevented if measure is taken to keep the product from oxidizing.
Maintenance:
Please do not return this product to the store. For technical assistance on assembly or replacement parts. Please
call Sunjoy Industries at 1-866-578-6569 from 8:00 am EST to 8:00 pm PST or fax the replacement part form
which is in the box to 1-740-283-3549 or Email customer.care@sunjoygroup.com for ass
Important:
Made in China
2016-3
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8

Sunjoy 110101057 User manual

Brand
Sunjoy
Model
110101057
Type
User manual
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents