2. Kichler Lighting
  3. 44023NBR

Kichler Lighting 44023NBR User manual

  • Hello! I am an AI chatbot trained to assist you with the Kichler Lighting 44023NBR User manual. I’ve already reviewed the document and can help you find the information you need or explain it in simple terms. Just ask your questions, and providing more details will help me assist you more effectively!
IS-44023-US
We’re here to help 866-558-5706
Hrs: M-F 9am to 5pm EST
A
D
C
K
J
E
F
G
H
I
O
N
M
L
B
P
Never connect ground wire to black or white power
supply wires.
7) Make wire connecon. Reference chart below for correct
connecons and wire accordingly.
Connect Black or Red
Supply Wire to:
Connect White Supply
Wire to:
Black White
*Parallel cord (round &
smooth)
*Parallel cord (square &
ridged)
Clear, Brown, Gold or
Black without Tracer
Clear, Brown, Gold or Black
with Tracer
Insulated wire (other
than green) with copper
conductor
Insulated wire (other
than green) with silver
conductor
*Note: When parallel wire (SPT
1 & SPT 2) are used. The neutral
wire is square shaped or ridged
and the other wire will be round
in shape or smooth (see illus.)
Neutral Wire
8) Aach the inspecon cable[P] to the mounng plate
or to the inside of the mounng box. Raise canopy
to ceiling. NOTE: Be certain wires do not get pinched
between the canopy and ceiling.
9) Use the two (2) barrel knobs[K] and two (2)
lockwashers[J] to secure canopy through the sides of the
canopy. Tighten to secure.
10) Lower glass[N] over the light sockets of the main body
and thread on the socket ring[M] to secure into place.
Repeat for the other sockets.
11) Insert recommended bulbs. (Not supplied)
12) Lower the shades[O] onto the installed glass.
GREEN GROUND
SCREW
CUPPED
WASHER
OUTLET BOX
GROUND
FIXTURE
GROUND
DIMPLES
WIRE CONNECTOR
OUTLET BOX
GROUND
GREEN GROUND
SCREW
FIXTURE
GROUND
a
b
Fixture Diagram
Parts List
Cauons
CAUTION – RISK OF SHOCK –
Disconnect Power at the main circuit breaker panel or main
fusebox before starng and during the installaon.
WARNING:
This xture is intended for installaon in accordance
with the Naonal Electrical Code (NEC) and all local code
specicaons. If you are not familiar with code requirements,
installaon by a cered electrician is recommended.
Installaon Instrucons
[A] Mounting
Plate
[B] Screws
[C] Plate
Mounting
Screws
[D] Outlet Box
[E] Canopy
[F] Chains
[G] Decorative
Loops
[H] Stem
[I] Main Body
[J] Lockwashers
[K] Barrel Knobs
[L] Dry Wall
Anchors
[M] Socket Ring
[N] Glass
[O] Shades
[P] Inspection
Cable
1) Run the wire through the stem[H] and through the
decorave loop[G] and install onto the main body[I].
Install the other stem and decorave loop to the other
side.
2) Aach both chains[F] to the decorave loops[G] of main
body. Aach chain to the loops on the canopy[E]. Close
the links by wrapping in a cloth and squeezing closed
using pliers.
3) Weave electrical wire and ground wire through chain
links[F] no more than 3 inches apart. Pass wire through
the canopy.
4) Aach mounng plate[A] to outlet box[D] using the
plate mounng screws[C]. The mounng plate can be
adjusted to suit posion of xture.
5) Use the two (2) dry wall anchors[L], one on each end of
the backplate and secure with the two (2) screws[B].
6) Grounding instrucons: (See Illus. a or b).
a) On xtures where mounng plate is provided with a
hole and two raised dimples, wrap ground wire from
outlet box around green ground screw, and thread
into hole.
b) On xtures where a cupped washer is provided,
aach ground wire from outlet box under cupped
washer and green ground screw, and thread into
mounng strap.
If xture is provided with ground wire, connect xture
ground wire to outlet box ground wire with wire
connector aer following the above steps.
Installaon Instrucons (connued)
Page is loading ...
IS-44023-CB
We’re here to help 866-558-5706
Hrs: M-F 9am to 5pm EST
A
D
C
K
J
E
F
G
H
I
O
N
M
L
B
P
Never connect ground wire to black or white power
supply wires.
7) Make wire connecon. Reference chart below for correct
connecons and wire accordingly.
Connect Black or Red
Supply Wire to:
Connect White Supply
Wire to:
Black White
*Parallel cord (round &
smooth)
*Parallel cord (square &
ridged)
Clear, Brown, Gold or
Black without Tracer
Clear, Brown, Gold or Black
with Tracer
Insulated wire (other
than green) with copper
conductor
Insulated wire (other
than green) with silver
conductor
*Note: When parallel wire (SPT
1 & SPT 2) are used. The neutral
wire is square shaped or ridged
and the other wire will be round
in shape or smooth (see illus.)
Neutral Wire
8) Aach the inspecon cable[P] to the mounng plate
or to the inside of the mounng box. Raise canopy
to ceiling. NOTE: Be certain wires do not get pinched
between the canopy and ceiling.
9) Use the two (2) barrel knobs[K] and two (2)
lockwashers[J] to secure canopy through the sides of the
canopy. Tighten to secure.
10) Lower glass[N] over the light sockets of the main body
and thread on the socket ring[M] to secure into place.
Repeat for the other sockets.
11) Insert recommended bulbs. (Not supplied)
12) Lower the shades[O] onto the installed glass.
GREEN GROUND
SCREW
CUPPED
WASHER
OUTLET BOX
GROUND
FIXTURE
GROUND
DIMPLES
WIRE CONNECTOR
OUTLET BOX
GROUND
GREEN GROUND
SCREW
FIXTURE
GROUND
a
b
Fixture Diagram
Parts List
Cauons
CAUTION – RISK OF SHOCK –
Disconnect Power at the main circuit breaker panel or main
fusebox before starng and during the installaon.
WARNING:
This xture is intended for installaon in accordance
with the Naonal Electrical Code (NEC) and all local code
specicaons. If you are not familiar with code requirements,
installaon by a cered electrician is recommended.
Installaon Instrucons
[A] Mounting
Plate
[B] Screws
[C] Plate
Mounting
Screws
[D] Outlet Box
[E] Canopy
[F] Chains
[G] Decorative
Loops
[H] Stem
[I] Main Body
[J] Lockwashers
[K] Barrel Knobs
[L] Dry Wall
Anchors
[M] Socket Ring
[N] Glass
[O] Shades
[P] Inspection
Cable
1) Run the wire through the stem[H] and through the
decorave loop[G] and install onto the main body[I].
Install the other stem and decorave loop to the other
side.
2) Aach both chains[F] to the decorave loops[G] of main
body. Aach chain to the loops on the canopy[E]. Close
the links by wrapping in a cloth and squeezing closed
using pliers.
3) Weave electrical wire and ground wire through chain
links[F] no more than 3 inches apart. Pass wire through
the canopy.
4) Aach mounng plate[A] to outlet box[D] using the
plate mounng screws[C]. The mounng plate can be
adjusted to suit posion of xture.
5) Use the two (2) dry wall anchors[L], one on each end of
the backplate and secure with the two (2) screws[B].
6) Grounding instrucons: (See Illus. a or b).
a) On xtures where mounng plate is provided with a
hole and two raised dimples, wrap ground wire from
outlet box around green ground screw, and thread
into hole.
b) On xtures where a cupped washer is provided,
aach ground wire from outlet box under cupped
washer and green ground screw, and thread into
mounng strap.
If xture is provided with ground wire, connect xture
ground wire to outlet box ground wire with wire
connector aer following the above steps.
Installaon Instrucons (connued)
Page is loading ...
/