Kichler Lighting 52315BNB is a versatile lighting fixture that can be mounted on both rigid stems and loop/chain links. It features a canopy, mounting plate, stems, short threaded tubes, safety cable, lockwashers, hexnuts, and various screws for secure installation. The fixture includes a ground wire for safety and can accommodate multiple bulbs (not included). With its adjustable mounting plate and the ability to customize the number of stems, this fixture provides flexibility in positioning and height.
Kichler Lighting 52315BNB is a versatile lighting fixture that can be mounted on both rigid stems and loop/chain links. It features a canopy, mounting plate, stems, short threaded tubes, safety cable, lockwashers, hexnuts, and various screws for secure installation. The fixture includes a ground wire for safety and can accommodate multiple bulbs (not included). With its adjustable mounting plate and the ability to customize the number of stems, this fixture provides flexibility in positioning and height.
IS-52315-US
We’re here to help 866-558-5706
Hrs: M-F 9am to 5pm EST
13) Grounding instrucons: (See Illus. a or b).
a) On xtures where mounng plate is provided with a
hole and two raised dimples, wrap ground wire from
outlet box around green ground screw, and thread
into hole.
b) On xtures where a cupped washer is provided,aach
ground wire from outlet box under cupped washer
and green ground screw, then thread into mounng
plate.
If xture is provided with ground wire, connect xture
ground wire to outlet box ground wire with wire connector
aer following the above steps. Never connect ground
wire to black or white power supply wires.
14) Make wire connecon. Reference chart below for correct
connecons and wire accordingly.
Connect Black or Red
Supply Wire to:
Connect White Supply
Wire to:
Black White
*Parallel cord (round &
smooth)
*Parallel cord (square &
ridged)
Clear, Brown, Gold or
Black without Tracer
Clear, Brown, Gold or Black
with Tracer
Insulated wire (other
than green) with copper
conductor
Insulated wire (other
than green) with silver
conductor
*Note: When parallel wire (SPT
1 & SPT 2) are used. The neutral
wire is square shaped or ridged
and the other wire will be round
in shape or smooth
(see illus.)
Neutral Wire
15) Aach the safety cable[D] to the mounng plate or to the
inside of the outlet box.
16) Push xture to ceiling, carefully passing mounng screws
through holes in canopy[H].
NOTE: Be certain wires do not get pinched between
canopy and ceiling.
17) Use knobs[R] and lockwashers[S] to secure canopy.
Tighten to secure.
18) Carefully lower glass[T] down over socket onto decorave
cup.
19) Carefully lower candle sleeve[U] down over socket. Sleeve
must seat at against glass.
20) Repeat steps 18-19 for remaining glass pieces.
21) Insert recommended bulbs. (Not supplied).
GREEN GROUND
SCREW
CUPPED
WASHER
OUTLET BOX
GROUND
FIXTURE
GROUND
DIMPLES
WIRE CONNECTOR
OUTLET BOX
GROUND
GREEN GROUND
SCREW
FIXTURE
GROUND
a
b
Fixture Diagram
Parts List
Cauons
CAUTION – RISK OF SHOCK –
Disconnect Power at the main circuit breaker panel or main fusebox before starng and during
the installaon.
WARNING:
This xture is intended for installaon in accordance with the Naonal Electrical Code (NEC) and all
local code specicaons. If you are not familiar with code requirements, installaon by a cered
electrician is recommended.
CLEANING:
• Always be certain that electric current is turned o before cleaning.
• Only a so damp cloth should be used. Harsh cleaning products may damage the nish.
Installaon Instrucons
[A] Stems
[B] Short Threaded Tubes
[C] Outlet Box
[D] Safety Cable
[E] Lockwasher
[F] Hexnut
[G] Mounting Plate
[H] Canopy
[I] Plate Mounting Screws
[J] Mounting Screws
[K] Dry Wall Anchors
[L] Second Loop
[M] Chain Link
[N] Screws
[O] Fixture Body
[P] Ground Wire Loop
[Q] First Loop
[R] Knobs
[S] Lockwashers
[T] Glass
[U] Candle Sleeve
RIGID STEM MOUNT
1) On side of xture with xture wires, pass xture wires through stems[A] and short threaded
tubes[B], screw stems together using short threaded tubes, and screw stems onto threads
protruding from top of xture body[O].
2) On opposite side of xture (without xture wires) screw a second set of stems together using
short threaded tubes (same number of stems and short threaded tubes from previous step but
without xture wire) and screw stems onto opposite threads protruding from top of xture
body.
NOTE: Thread locking compound must be applied to all stem threads as noted with symbol (4)
to prevent accidental rotaon of xture during cleaning, relamping, etc.
NOTE: A minimum of two (2) 12 inch stems must be used when mounng of xture, one (1) per
side. Pass xture wires through remaining stems and screw stems together.
3) On side of xture with xture wires, pass xture wires through one short threaded tube[B].
Screw short threaded tube onto top of stem.
4) On opposite side of xture (without xture wires), screw one short threaded tube onto top of
stem.
5) Pass xture wires through hole in canopy[H]. Lower canopy down towards stems. Pass holes in
canopy over ends of short threaded tubes on top of the stems.
6) On side of xture with xture wires, pass xture wires through loop of safety cable[D]. Slip loop
of safety cable over end of short threaded tube protruding from inside of canopy.
7) Pass xture wires through lockwasher[E]. Place lockwasher onto end of short threaded tube
protruding from inside canopy.
8) Pass xture wires through hexnut[F]. Thread hexnut onto end of short threaded tube.
NOTE: Fixture wires should not be cut shorter than 20 inches from above the canopy.
9) On opposite side of xture (without xture wires), place loop of ground wire[P] over short
threaded tube protruding from inside of canopy and secure into place with a lock washer and
hexnut as shown.
10) Find the appropriate threaded holes on mounng plate[G]. Assemble mounng screws[J] into
threaded holes (if they are not already installed).
11) Aach mounng plate to outlet box[C] using the plate mounng screws[I]. Mounng plate can
be adjusted to suit posion of xture.
12) Use the two (2) drywall anchors[K], one on each end of the mounng plate, and secure with
the two (2) screws[N].
Installaon Instrucons (connued)
LOOP / CHAIN LINK MOUNT
1) Follow steps 1 and 2 from “Rigid Stem Mount” Instrucons.
2) Thread one short threaded tube[B] into end of each small
loop[Q, L].
3) On side of xture with xture wires, pass xture wires
through rst loop[Q]. Thread rst loop onto end of last stem.
4) Pass xture wires through second loop[L] and through hole
in canopy[H]. Pass short threaded tube at end of second loop
through hole in canopy.
5) Pass xture wires through loop of safety cable[D]. Slip loop
of safety cable over end of short threaded tube protruding
from inside of canopy.
6) Pass xture wires through lockwasher[E]. Place lockwasher
onto end of short threaded tube protruding from inside
canopy.
7) Pass xture wires through hexnut[F]. Thread hexnut onto
end of short threaded tube.
NOTE: Fixture wires should not be cut shorter than 20
inches from above the canopy.
8) On opposite side of xture (without xture wires), Thread
rst loop[Q] onto end of last stem. Pass threaded pipe at end
of second loop[L] through hole in canopy.
9) Place loop of ground wire[P] over short threaded tube
protruding from inside of canopy and secure into place with a
lock washer and hexnut as shown.
10) Aach open chain link[M] to small loops at end of each stem
and to small loops on canopy and close the open chain link by
placing a piece of cloth over the open link and using a pair of
pliers gently squeeze the link closed.
11) Follow steps 10 - 21 from “Rigid Stem Mount” Instrucons.
T
U
►
►
►
►
B
Q
M
L
L
M
Q
A
B
N
J
K
C
I
G
P
F
E
F
E
H
R
S
D
O
Page is loading ...
Page is loading ...
-
1
-
2
-
3
Kichler Lighting 52315BNB is a versatile lighting fixture that can be mounted on both rigid stems and loop/chain links. It features a canopy, mounting plate, stems, short threaded tubes, safety cable, lockwashers, hexnuts, and various screws for secure installation. The fixture includes a ground wire for safety and can accommodate multiple bulbs (not included). With its adjustable mounting plate and the ability to customize the number of stems, this fixture provides flexibility in positioning and height.
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI
in other languages
Related papers
-
Kichler Lighting 52140BK User manual
-
Kichler Lighting 52033BK User manual
-
Kichler Lighting 52263OZ User manual
-
Kichler Lighting 52224FXG User manual
-
Kichler Lighting 52054CG User manual
-
Kichler Lighting 52123BNB User manual
-
Kichler Lighting 52282NI User manual
-
Kichler Lighting 52273BK User manual
-
Kichler Lighting 52091AUB User manual
-
Kichler Lighting 49309BK User manual
Other documents
-
Kichler 52263OZ Operating instructions
-
OK LIGHTING OK-5117H Installation guide
-
-
-
-
-
-
-
-
