Riva RC3512HD-6311 Quick Installation Guide

Brand: Riva

Model: RC3512HD-6311

Type: Quick Installation Guide

Quick Installation Guide

Before operating the unit, please read this manual thoroughly and

keep it for future reference.

Please access our website and download necessary IPAdminTool first:

http://www.rivatech.de/en/downloads/software

NC3512(63)11-2015-A

About the manuals

This manual provides the instructions for the quick installation

and the basic configuration of your IP device. For more detailed

information about the installation and configuration, refer to the

device’s installation guide and the web page user’s manual.

Part names and functions

Please check the name and the position of each part by

referring to the following image.

Terminal Connector: Connect the provided 6 pin terminal block for

a sensor, an alarm and a DC12V power cable.

Ethernet Connector: Connect an RJ-45 LAN cable for 10/100 Base-T

Ethernet (PoE supported).

Reset Button: Press the button either for the restart or the factory

default of the device. For restart,

press the button only for 2

seconds while the device is powered on.

Wait for the system to

reboot. For factory default,

press the button for 10 seconds while

the device is powered on.

Wait for the system to reboot.

mircoSD/SDHC Card Slot: Insert a card up to 32GB supported.

Class 4 or the above is recommended for HD recording.

Installation

There is only one type of mounting explained in this manual. Refer

to the device’s installation guide for more various mounting types.

CAUTION

To prevent from damage, place the camera on a stable and non-

vibrating surface.

Adjusting angle of camera

CAUTION

Refrain from continuous rotation of the camera gimbal to a single

direction as it is linked with the internal cables.

NOTE

Tighten the tilt stopper after the tilt angle is confirmed.

Adjusting zoom and focus

The zoom and focus can be managed via the camera’s web page (path:

Setup>Video>Zoom/Focus). Thus, it is necessary to connect the device

on a network in advance to the zoom and focus adjustment.

- Adjust zoom/focus by clicking the arrow buttons: The buttons

move the lens more extensively than the buttons .

- If you want to set the focus automatically, click One Click Focus.

- If focus point is considered misaligned, reset it to a zero point by

clicking Calibrate.

C. For the horizontal rotation of the

lens, rotate the inner liner clockwise

or counter-clockwise.

(The rotating range is limited to 358 degrees.)

A. To pan, rotate the gimbal bracket

clockwise or counter-clockwise.

(The panning range is limited to 358 degrees.)

B. To tilt, tilt the gimbal by referring to

the image on the left.

inner liner

M4x30 screw

DO DI

1 1C C

DC12V

ETHERNET

RESET

MICRO

DO DI

1 1C C

DC12V

ETHERNET

RESET

MICRO

ETHERNET

WIRE

micro

SD/SDHC card slot

DO DI DC 12V

Ethernet

connector

Reset

button

Terminal connector

DO DI

1 1C C

DC12V

ETHERNET

RESET

MICRO

DO DI

1 1C C

DC12V

ETHERNET

RESET

MICRO

ETHERNET

WIRE

gimbal

bracket

gimbal

tilt

stopper

1) Place the installation template included in the package on a

desired installation surface.

2) Drill three holes for the plastic anchors based on the template

paper, and insert the plastic anchors into the holes. (In case you

need to route the cables through the mounting surface, drill the

hole to pass the cables based on the size of the cable entry hole).

3) Attach the provided silicon waterproof band to the bottom of

the camera body for the prevention of water permeation.

4) Open the dome cover with the provided L wrench (3mm),

install the provided ferrite core to the LAN cable by referring to

the squared image on the bottom left of this page, and connect

all the necessary cables dropped from the ceiling to the

corresponding connectors on the camera.

5) Prepare the screws (M4x30) with the O-rings inserted. Then,

place the camera body to match the alignment holes with the

corresponding plastic anchors, insert the O-ring inserted screws

into the screw holes on the camera body, and tighten them into

the plastic anchors with a screw driver.

6) Adjust the angle of the camera. Refer to the section,

Adjusting angle of camera for more details.

7) Adjust zoom and focus of the camera. Refer to Adjusting

zoom and focus for more details.

8) Reattach the dome cover to the camera body by aligning the

alignment marks on both the dome cover and the camera body.

9) Once the dome cover and the camera body are properly

aligned, tighten the bolts on the dome cover into the camera

body with the provided L wrench for the firm attachment.

Setting up network environment

The default IP address of the device is 192.168.XXX.XXX. Users can

identify the IP address of the device by converting the MAC

address’s hexadecimal numbers. The MAC address is at the bottom

of the device. Be sure that the device and the PC are on the same

network area before the installation.

Generic IP Environment

1) Convert the device’s MAC address to the IP address. Refer to the

Hexadecimal-Decimal Conversion Table at the end of this manual.

IPAdminTool

IPAdminTool is a management tool to automatically scan all the

network products for the devices’ administrative tasks, which

include network configurations, firmware update, device reboot,

factory default, and device organization.

To modify the device’s default IP address for a customized network

area;

1) Find the device from IPAdminTool’s list and highlight the device’s

name.

2) Right-click the mouse and select IP Address; The IP setup window

will appear.

3) In the IP Setup’s window, information under Local Network

information displays the user/PC’s network area information.

Those information need to be incorporated to the IP Address,

Subnet Mask, Gateway, and DNS boxes, except the last 2 sets of IP

Address, which are to be the unique numbers for the device. Refer

to the image above for the setting

4) Click Setup.

Viewing video on web page

Once the device’s IP address has been identified, type the URL in a

web browser to access the camera. At the first time access, the

installation window may pop up.

1) When the browser asks to install the AxUMF software, click the

Install button to proceed.

2) When the Setup installation pop-up window appears, click the

Install button to preceed with the rest of the installation.

NOTE

The figures during the installation process may differ depending on

the system OS and the IE version.

SETUP page

To setup the device configuraiton:

1) Click the Setup button on the upper left corner of the web page.

2) Enter the user name and the password when the login page is

displayed. Then, click the OK button.

(The default user name and the password are root and pass.)

To learn how to set up the camera on the web page for the

advanced configuration, refer to the webpage user’s manual.

Safe mode

Your device will get restarted in safe mode if the device does not

completely boot certain times. The main causes for safe mode are

as follows.

* The power supply is continually unplugged certain times in the

middle of system booting.

* The firmware files required for system booting are damaged.

* There are conflicts in the system settings.

You will see the page to indicate that your device is in safe mode

and to guide you what to do in steps. Follow the instructions on the

webpage according to each step.

NOTE

One of the methods to update firmware is using IPAdminTool.

Please refer to the IPAdminTool manual for the detailed procedure.

NOTE

If your device is still in safe mode after trying to update firmware,

please contact your local agency to get further assistance.

Hexadecimal-Decimal conversion table

Refer to the following table when converting the MAC address of

your device to IP address.

Hex

Dec

Hex

Dec

Hex

Dec

Hex

Dec

Hex

Dec

Hex

Dec

Hex

Dec

111

148

185

222

112

149

186

223

113

150

187

224

114

151

188

225

115

152

189

226

116

153

190

227

117

154

191

228

118

155

192

229

119

156

193

230

120

157

194

231

121

158

195

232

122

159

196

233

123

160

197

234

124

161

198

235

125

162

199

236

126

163

200

237

127

164

201

238

128

165

202

239

129

166

203

240

130

167

204

241

131

168

205

242

132

169

206

243

133

170

207

244

134

171

208

245

135

172

209

246

136

173

210

247

100

137

174

211

248

101

138

175

212

249

102

139

176

213

250

103

140

177

214

251

104

141

178

215

252

105

142

179

216

253

106

143

180

217

254

107

144

181

218

255

108

145

182

219

109

146

183

220

110

147

184

221

Riva RC3512HD-6311 Quick Installation Guide

Brand: Riva

Model: RC3512HD-6311

Type: Quick Installation Guide

Download PDF

report

Riva RC3512HD-6311 Quick Installation Guide

Riva RC3512HD-6311 Quick Installation Guide

Related papers