Juno P6300 User manual

Type
User manual

Juno P6300 is a track lighting adapter designed for use with Juno Trac fixtures. It allows for easy installation and removal of fixtures from the track, and can be used to create a variety of lighting configurations. The adapter features a polarity line to ensure proper alignment and a latch to secure the fixture in place. It also includes a second circuit positioning option for use with two-circuit Trac sections.

Juno P6300 is a track lighting adapter designed for use with Juno Trac fixtures. It allows for easy installation and removal of fixtures from the track, and can be used to create a variety of lighting configurations. The adapter features a polarity line to ensure proper alignment and a latch to secure the fixture in place. It also includes a second circuit positioning option for use with two-circuit Trac sections.

For Juno Trac Adapter*
One Lithonia Way Conyers, GA 30012 1-800-705-SERV (7378) www.acuitybrands.com
©2020 Acuity Brands Lighting, Inc. P6300 Rev 10/2022 1 of 2
INSTALLATION INSTRUCTIONS
Step 1 Find the latch and the polarity line. Align parts as
shown and insert the adapter box into the track. (Fig. 1)
Step 2 Pull down the latch while rotating the adapter box
90 degrees clockwise. (Fig. 2)
Step 3 Final Position: Latch snaps into place between
extrusion rails. Arrows on latch point toward the polarity
line. (Fig. 3)
Step 1 Raise the contact marked P(on switch side) by
inserting a thin screwdriver blade under contact. Pull up
into position as shown. (Fig. 4)
Step 2 Insert contact support (supplied with 2-circuit Trac
section) by tilting and snapping into position under the P
contact as shown. (Fig. 5)
WARNING Read all of these installation instructions before installing.
SAVE THESE INSTRUCTIONS
Fig. 1 Fig. 2
Fig. 3 Fig. 4
Fig. 5
POLARITY LINE
PCONTACT
Fig. 6
Step 3 Ensure contact support is snapped and locked into
position. (Fig. 6) Follow instructions for inserting into track.
SECOND CIRCUIT POSITIONING
FIXTURE INSTALLATION
LATCH
(LIFT)
(ROTATE)
(INSERT)
CONTACT
SUPPORT FINAL POSITION OF
CONTACT SUPPORT
*Juno Trac adapter size and style may vary.
(PULL)
Coming Soon
For Juno Trac Adapter*
INSTALLATION INSTRUCTIONS
One Lithonia Way Conyers, GA 30012 1-800-705-SERV (7378) www.acuitybrands.com
©2020 Acuity Brands Lighting, Inc. P6300 Rev 10/2022 2 of 2
Problem Cause Remedy
Fixture doesn't turn
on
Track not energized Ensure track has power
Adapter switch is in the
"Off" position
Ensure the power switch on the track fixture adapter is in the "On" position,
see Fig. 9
Fixture installed
incorrectly
Ensure fixture is installed correctly, with the arrows on the latch pointing
towards the polarity line as shown in Fig. 3
Ensure contacts aren't bent from installing the fixture incorrectly, see Fig. 7
"P" Contact adjusted
incorrectly
Ensure "P" contact isn't bent from adjusting incorrectly, see Fig. 8
Bent contact from adjusting the wrong contact, see Fig. 4, 5, & 6 for proper
adjustment method
TROUBLESHOOTING
Fig. 8 Correct Incorrect
Bent Contact
Raised
Contact
Fig. 7 Correct
Bent Contact
Raised
Contact
Incorrect
Fig. 9
Single Circuit Posion
Used with T, TU, and R Series Track
Two Circuit Posion
Used with TU Series Track
O On
Move Switch To
OnPosition
Coming Soon
  • Page 1 1
  • Page 2 2

Juno P6300 User manual

Type
User manual

Juno P6300 is a track lighting adapter designed for use with Juno Trac fixtures. It allows for easy installation and removal of fixtures from the track, and can be used to create a variety of lighting configurations. The adapter features a polarity line to ensure proper alignment and a latch to secure the fixture in place. It also includes a second circuit positioning option for use with two-circuit Trac sections.

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI