Lithonia Lighting B-RSX LED Area Lights User manual

Brand: Lithonia Lighting

Model: B-RSX LED Area Lights

Type: User manual

READ AND FOLLOW ALL SAFETY INSTRUCTIONS!

SAVE THESE INSTRUCTIONS AND DELIVER TO OWNER AFTER INSTALLATION

· To reduce the risk of death, personal injury or property damage from re, electric shock, falling parts, cuts/

abrasions, and other hazards please read all warnings and instructions included with and on the xture box and

all xture labels.

· Before installing, servicing, or performing routine maintenance upon this equipment, follow these general

precautions.

· Installation and service of luminaires should be performed by a qualied licensed electrician.

· Maintenance of the luminaires should be performed by person(s) familiar with the luminaires’ construction and

operation and any hazards involved. Regular xture maintenance programs are recommended.

· It will occasionally be necessary to clean the outside of the refractor/lens. Frequency of cleaning will depend on

ambient dirt level and minimum light output which is acceptable to user. Refractor/lens should be washed in a

solution of warm water and any mild, non-abrasive household detergent, rinsed with clean water and wiped dry.

Should optical assembly become dirty on the inside, wipe refractor/lens and clean in above manner, replacing

damaged gaskets as necessary.

· DO NOT INSTALL DAMAGED PRODUCT! This luminaire has been properly packed so that no parts should have

been damaged during transit. Inspect to conrm. Any part damaged or broken during or after assembly should

be replaced.

· Recycle: For information on how to recycle LED electronic products, please visit www.epa.gov.

· These instructions do not purport to cover all details or variations in equipment nor to provide every possible

contingency to meet in connection with installation, operation, or maintenance. Should further information

be desired or should particular problems arise which are not covered suciently for the purchaser’s or owner’s

purposes, this matter should be referred to Acuity Brands Lighting, Inc.

Disconnect or turn o power before installation or

servicing.

Verify that supply voltage is correct by comparing it with

the luminaire label information.

Make all electrical and grounded connections in

accordance with the National Electrical Code (NEC) and

any applicable local code requirements.

All wiring connections should be capped with UL

approved recognized wire connectors.

WARNING

RISK OF ELECTRIC SHOCK

Allow lamp/xture to cool before handling. Do not

touch enclosure or light source.

Do not exceed maximum wattage marked on

luminaire label.

Follow all manufacturer’s warnings, recommendations

and restrictions for: driver type, burning position,

mounting locations/methods, replacement and

recycling.

WARNING

RISK OF BURN

CAUTION

RISK OF FIRE

Keep combustible and other materials that can burn,

away from lamp/lens.

Do not operate in close proximity to persons,

combustible materials or substances aected by heat

or drying.

CAUTION

RISK OF INJURY

Wear gloves and safety glasses at all times when

removing luminaire from carton, installing, servicing or

performing maintenance.

Avoid direct eye exposure to the light source while it is on.

Coming Soon

Never connect components under load.

Do not mount or support these xtures in a manner that can cut the outer jacket or damage wire insulaon.

Unless individual product specicaons deem otherwise: Never connect an LED product directly to a dimmer packs,

occupancy sensors, ming devices, or other related control devices. LED xtures must be powered directly o a switched

circuit.

Unless individual product specicaons deem otherwise: Do not restrict xture venlaon. Allow for some volume of

airspace around xture. Avoid covering LED xtures with insulaon, foam, or other material that will prevent convecon

or conducon cooling.

Unless individual product specicaons deem otherwise: Do not exceed xtures maximum ambient temperature.

Only use xture in its intended locaon.

LED products are Polarity Sensive. Ensure proper Polarity before installaon.

Electrostac Discharge (ESD): ESD can damage LED xtures. Personal grounding equipment must be worn during all

installaon or servicing of the unit.

Do not touch individual electrical components as this can cause ESD, shorten lamp life, or alter performance.

Some components inside the xture may not be serviceable. In the unlikely event your unit may require service, stop

using the unit immediately and contact an ABL representave for assistance.

Always read the xtures complete installaon instrucons prior to installaon for any addional xture specic warnings.

CAUTION: RISK OF PRODUCT DAMAGE

Please see product specic installation instructions for additional warnings or any applicable FCC or other regulatory statements.

Failure to follow any of these instructions could void product warranties. For a complete listing of product Terms and Conditions, please visit www.acuitybrands.com.

Our Brands Indoor/Outdoor Indoor Lighting Outdoor Lighting Controls Daylighting

Lithonia Lighting Gotham American Electric Lighting DARK TO LIGHT SunOptics

Carandini Mark Architectural Lighting Antique Street Lamps LC&D

Holophane Peerless Hydrel ROAM

RELOC Renaissance Lighng Tersen Sensor Switch

Light Concepts Winona Lighting Synergy

Acuity Brands Lighting, Inc. assumes no responsibility for claims arising out of improper or careless installation or handling of its products.

ABL LED General Warnings, Form No. 503.203

Coming Soon

Part Number: RJ521505 Rev D

Revision Date: 8-1-22

Installation Instructions

WBA 2018

Lithonia Lighting Outdoor • One Lithonia Way • Conyers, Georgia 30012

Phone: 1-800-705-7378 • www.lithonia.com

(Figure 1A)

1. CAUTION: APPLY A CONTINUOUS BEAD OF WEATHER–PROOF CAULKING BETWEEN MOUNT-

ING BASE PLATE AND WALL TO ENSURE WEATHER–TIGHT INTEGRITY OF ELECTRICAL COMPONENTS.

2. Secure base plate to wall with (4) 1/4” diameter fasteners (by

others) using the (4) holes located on the outer corners of the base plate

oriented as shown with the embossed part number on the top.

Check the base plate to conrm that it is level and plumb in all direc-

tions.

3. Prepare the cover plate by verifying the factory installed gasket is in place on the backside of the cover plate.

4. Note for the next steps the curved portion of the cover plate should point upwards when mounted to the wall.

Note: The next pages are luminaire specic.

Choose the SECTION B installation steps corresponding to the luminaire being installed (also reference the

luminaire installation instruction sheet).

SECTION A

Figure 1A

To wall

Gasket

(factory installed)

Step 3

Base plate

Step 2

Hex set screws

(See Section C for

installation)

Caulking by

others

Step 1

Base plate

Step 2

(4) 1/4" fasteners

Cover plate

Step 4

Coming Soon

1. Make certain that all power is disconnected prior to installing the xture.

2. For wall mounting, slide the square pole adaptor onto the threaded rod rst.

Insert threaded rod of luminaire arm into top hole of WBA cover plate and through the unthreaded top hole of backing plate.

Align the center unthreaded hole of the backing plate with the WBA cover plate's center hole. See Figure 1B.

3. Using 9/16” wrench tighten nut onto threaded rod to 20-25 -lb.

Installation Instructions

WBA 2018

SECTION B-RAD1

Steel bar backing

plate provided with

luminaire

Cover plate

Base plate (See

Section A for instal-

lation)

Square pole adaptor

4. Using T20 driver, loosen single screw holding wiring access cover and set aside for reinstallation. See Figure 2B.

5. Using the supplied 3/8” bolt, slide it into the arm, through the bottom hole on the square pole adaptor, cover plate and into

lower threaded hole of backing plate. Using 9/16” wrench to 20-25 -lb. See Figure 3B.

6. Pull wires through the center hole of the arm, square pole adaptor, cover plate, and backing plate.

7. By aligning hooks within the cutouts in the front of the arm, replace the wire access cover (from step 4) and tighten the screw

using T20 driver to 15-20 in-lb. See Figure 4B.

8. Proceed to section C.

Part Number: RJ521505 Rev D

Revision Date: 8-1-22

Lithonia Lighting Outdoor • One Lithonia Way • Conyers, Georgia 30012

Phone: 1-800-705-7378 • www.lithonia.com

readed rod

Hex set screws

(See Section C for installation)

washer

and nut

Figure 1B

3/8” Bolt

Door Hook Cutouts

Figure 2B

Figure 3B

Figure 4B

readed

hole

Coming Soon

Part Number: RJ521505 Rev B

Revision Date: 8-1-22

Installation Instructions

WBA 2018

Lithonia Lighting Outdoor • One Lithonia Way • Conyers, Georgia 30012

Phone: 1-800-705-7378 • www.lithonia.com

1. Open up the luminaire carton and locate the threaded steel bar, and the 2" long, 3/8” diameter lock bolts (2).

Stop Important: Installing a RSX, KAX or VCPG series luminaire, you will discard the 1-1/2” long bolts that came with

the wall mounting assembly and use the 2” long luminaire bolts.

2. On the underneath side of the luminaire arm, remove the wire access cover plate and set aside for reinstallation.

(Figure 1B)

3. Insert the 3/8” lock bolts through the back wall of the luminaire arm, through the cover plate, and then thread into

the threaded steel bar, simultaneously pulling the wires through the center hole (Figure 2B). e luminaire is supplied

with a clearance slot in the back to allow wires to be pulled into the WBA cover plate. Tighten the two bolts with a

9/16” hex socket to 20-30 -lbs.

4. Make sure that wires are not pinched and tuck excess wire up into the luminaire mounting area. Reinstall the wire

access cover plate from step 2, and tighten the two captive screws with the 9/64 Allen wrench to 18-20 in-lbs.

5. Proceed to section C.

12345678

TOLERANCE UNLESS NOTED

MATERIAL DESCRIPTION AND FINISH

ACUITY LIGHTING GROUP, INC.

ONE LITHONIA WAY CONYERS, GEORGIA 30012 U.S.A.

PRIOR TO PRODUCTION RELEASE.

SAMPLE MUST BE APPROVED BY

INFORMATION HEREIN CONTAINED IS THE

PROPERTY OF LITHONIA LIGHTING AND IS

TO BE HELD IN COMPLETE CONFIDENCE.

REPRODUCE WITH WRITTEN CONSENT ONLY.

SHT. TITLE:

DRAWING NO.

DATE

SCALE

LITHONIA ENGINEERING

9 10 11 12 13 14 15 16

www.acuitybrands.com www.lithonia.com

Pro/ENGINEER DRAWING

13-Sep-2018

3/8

WBA_OPTIONS

2 PLACE DECIMAL 0.01

3 PLACE DECIMAL 0.005

ANGLES 1/2

FRACTIONAL

DATEBYCHANGE DESCRIPTIONREVAPPDLOC

13-Sep-2018

MATERIAL: SEE BOM

N/A

MAIRELEASE TO PRODUCTIONMAI

Figure 2B

readed steel bar provided

with luminaire.

Hex set screws

2" Bolts

Cover plate

Hex set screws

Base plate (See Sec-

tion A for installation)

SECTION B-RSX/VCPG/KAX

RSX, VCPG KAX

Figure 1B

Coming Soon

Part Number: RJ521505 Rev D

Revision Date: 8-1-22

Lithonia Lighting Outdoor • One Lithonia Way • Conyers, Georgia 30012

Phone: 1-800-705-7378 • www.lithonia.com

Installation Instructions

WBA 2018

12345678

TOLERANCE UNLESS NOTED

MATERIAL DESCRIPTION AND FINISH

ACUITY LIGHTING GROUP, INC.

ONE LITHONIA WAY CONYERS, GEORGIA 30012 U.S.A.

PRIOR TO PRODUCTION RELEASE.

SAMPLE MUST BE APPROVED BY

INFORMATION HEREIN CONTAINED IS THE

PROPERTY OF LITHONIA LIGHTING AND IS

TO BE HELD IN COMPLETE CONFIDENCE.

REPRODUCE WITH WRITTEN CONSENT ONLY.

SHT. TITLE:

DRAWING NO.

DATE

SCALE

LITHONIA ENGINEERING

9 10 11 12 13 14 15 16

www.acuitybrands.com www.lithonia.com

Pro/ENGINEER DRAWING

13-Sep-2018

3/8

WBA_OPTIONS

2 PLACE DECIMAL 0.01

3 PLACE DECIMAL 0.005

ANGLES 1/2

FRACTIONAL

DATEBYCHANGE DESCRIPTIONREVAPPDLOC

13-Sep-2018

MATERIAL: SEE BOM

N/A

MAIRELEASE TO PRODUCTIONMAI

Figure 1B

readed steel bar provided

with luminaire.

Hex set screws

Bolts

Lockwashers Hex set screws

Mounting block

Cover plate

Base plate (See Sec-

tion A for installation)

SECTION B- AS2, AST2, MR2, MRT2, CSX, DSX G1

1. Prepare the cover plate by attaching the Aeris mounting block to the cover plate using (2) 3/8" diameter by 1-1/4"

bolts with lockwashers by inserting the bolts and washers into the mounting block through the cover plate and thread

into the threaded steel bar stock. Use a 9/16" socket or wrench and tighten securely (Figure 1B).

2. Open doorframe by loosening the (2) captive doorframe screws using 3/16" allen wrench.

3. Unhook safety-restraining cable. Loosen the 10-24 screw at the neck end of the doorframe 1/2 turn.

4. Remove door by sliding the hinge latch up and away from hinge, close door slightly and li door assembly o. Set

aside for reinstallation.

5. Pull the wires from the luminaire through the mounting block on the cover plate and through the center hole of the

threaded steel bar. Place luminaire onto the mounting block, being sure the wires are not being pinched. Tighten the

locking hex head bolt inside the arm with a 9/16" socket to 20-30 . lbs. torque.

6. Re-install the door assembly by placing hinge of doorframe on xed hinge rod of luminaire. Slide hinge latch on the

doorframe over hinge rod. Tighten 10-24 hinge latch screw. Reinstall safety-restraining cable (from step 3).

7. Proceed to section C.

Coming Soon

Part Number: RJ521505 Rev D

Revision Date: 8-1-22

Lithonia Lighting Outdoor • One Lithonia Way • Conyers, Georgia 30012

Phone: 1-800-705-7378 • www.lithonia.com

Installation Instructions

WBA 2018

12345678

TOLERANCE UNLESS NOTED

MATERIAL DESCRIPTION AND FINISH

ACUITY LIGHTING GROUP, INC.

ONE LITHONIA WAY CONYERS, GEORGIA 30012 U.S.A.

PRIOR TO PRODUCTION RELEASE.

SAMPLE MUST BE APPROVED BY

INFORMATION HEREIN CONTAINED IS THE

PROPERTY OF LITHONIA LIGHTING AND IS

TO BE HELD IN COMPLETE CONFIDENCE.

REPRODUCE WITH WRITTEN CONSENT ONLY.

SHT. TITLE:

DRAWING NO.

DATE

SCALE

LITHONIA ENGINEERING

9 10 11 12 13 14 15 16

www.acuitybrands.com www.lithonia.com

Pro/ENGINEER DRAWING

13-Sep-2018

3/8

WBA_OPTIONS

2 PLACE DECIMAL 0.01

3 PLACE DECIMAL 0.005

ANGLES 1/2

FRACTIONAL

DATEBYCHANGE DESCRIPTIONREVAPPDLOC

13-Sep-2018

MATERIAL: SEE BOM

N/A

MAIRELEASE TO PRODUCTIONMAI

Figure 1B

readed steel bar provided

with luminaire.

Hex set screws

Bolts

Mounting block

Hex set screws

Cover plate

Base plate (See

Section A for instal-

lation)

Lockwashers

SECTION B- AS1, AST1, MR1, MRT1

1. Prepare the cover plate by attaching the Aeris mounting block to the cover plate using (2) 3/8" diameter by 1-1/4"

bolts with lockwashers by inserting the bolts and washers into the mounting block through the cover plate and thread

into the threaded steel bar stock. Use a 9/16" socket or wrench and tighten securely (Figure 1B).

2. Open doorframe by loosening the (2) captive doorframe screws using 3/16" allen wrench.

3. Unhook safety-restraining cable. Loosen the 10-24 screw at the neck end of the doorframe 1/2 turn.

4. Remove door by sliding the hinge latch up and away from hinge, close door slightly and li door assembly o. Set

aside for reinstallation.

5. Pull the wires from the luminaire through the mounting block on the cover plate and through the center hole of the

threaded steel bar. Place luminaire onto the mounting block, being sure the wires are not being pinched. Tighten the

locking hex head bolt inside the arm with a 9/16" socket to 20-30 . lbs. torque.

6. Re-install the door assembly by placing hinge of doorframe on xed hinge rod of luminaire. Slide hinge latch on the

doorframe over hinge rod. Tighten 10-24 hinge latch screw. Reinstall safety-restraining cable (from step 3).

7. Proceed to section C.

Coming Soon

Part Number: RJ521505 Rev D

Revision Date: 8-1-22

Lithonia Lighting Outdoor • One Lithonia Way • Conyers, Georgia 30012

Phone: 1-800-705-7378 • www.lithonia.com

1. Pre-assemble the cover plate, mounting bar, threaded rods, gaskets and mounting arm together. (Figure 1B)

2. Open the door of the luminaire and insert the pre-assemble components through the back wall of the luminaire

housing, with thread rods into the luminaire housing, pulling the wires all the way through the center hole in the

threaded steel bar.

3. Tighten the two acorn nuts and lockwashers with a 9/16” hex socket to 20-30 -lbs (overtightening can damage

components and void warranties).

4. Close the door of the luminaire and tighten closing screws.

5. Proceed to section C.

SECTION B-KAD

readed steel bar provided

with luminaire.

Hex set screws

12345678

TOLERANCE UNLESS NOTED

MATERIAL DESCRIPTION AND FINISH

ACUITY LIGHTING GROUP, INC.

ONE LITHONIA WAY CONYERS, GEORGIA 30012 U.S.A.

PRIOR TO PRODUCTION RELEASE.

SAMPLE MUST BE APPROVED BY

INFORMATION HEREIN CONTAINED IS THE

PROPERTY OF LITHONIA LIGHTING AND IS

TO BE HELD IN COMPLETE CONFIDENCE.

REPRODUCE WITH WRITTEN CONSENT ONLY.

SHT.

TITLE:

DRAWING NO.

DATE

SCALE

LITHONIA ENGINEERING

9 10 11 12 13 14 15 16

www.acuitybrands.com www.lithonia.com

Pro/ENGINEER DRAWING

13-Sep-2018

3/8

WBA_OPTIONS

2 PLACE DECIMAL 0.01

3 PLACE DECIMAL 0.005

ANGLES 1/2

FRACTIONAL

DATEBYCHANGE DESCRIPTIONREVAPPDLOC

13-Sep-2018

MATERIAL: SEE BOM

N/A

MAIRELEASE TO PRODUCTIONMAI

Inside

luminaire

Mounting arm

Gaskets

read rods

Cover plate

Base plate (See Section

A for installation)

Figure 1B

Installation Instructions

WBA 2018

Coming Soon

Part Number: RJ521505 Rev CD

Revision Date: 8-1-22

Lithonia Lighting Outdoor • One Lithonia Way • Conyers, Georgia 30012

Phone: 1-800-705-7378 • www.lithonia.com

1. Make all wiring connections via the supplied wire leads in accordance with NEC and local codes.

2. Place the entire luminaire/cover plate assembly onto the base plate and have someone tighten the top (2) 3/8”

x 1-1/4” stainless steel recessed hex set screws until 3/8” to 1/4” of the screw threads are still visible. (Figure 1C)

3. Now tighten the bottom (2) 3/8” x 1-1/4” stainless steel recessed hex set screws until 3/8” to 1/4” of the screw

threads are still visible.

4. Now alternating between the top two and bottom two set screws, gently tighten until snug (approximately one

thread will remain showing on each screw).

CAUTION THE NEXT STEPS WILL REQUIRE ASSISTANCE

SECTION C

Figure 1C

Hex set

screws (4)

Installation Instructions

WBA 2018

Coming Soon

Lithonia Lighting B-RSX LED Area Lights User manual

Lithonia Lighting B-RSX LED Area Lights User manual

Lithonia Lighting B-RSX LED Area Lights User manual

Related papers

Other documents