Auralex Studio6™ User guide

Brand: Auralex

Model: Studio6™

Type: User guide

Auralex Studio6™

Auralex® Studio6™ Bass Traps are designed to improve the acoustic performance of your room or studio. They can be used to reduce standing waves, flutter echoes, and other acoustic problems.

Features:

Made from high-quality Studiofoam®
Lightweight and easy to install
Can be mounted on walls, ceilings, or corners
Available in a variety of sizes and colors

Use Cases:

Home studios
Professional recording studios
Home theaters
Offices
Schools
Churches
Other spaces where acoustic performance is important

Auralex Studio6™

Auralex® Studio6™ Bass Traps are designed to improve the acoustic performance of your room or studio. They can be used to reduce standing waves, flutter echoes, and other acoustic problems.

Features:

Made from high-quality Studiofoam®
Lightweight and easy to install
Can be mounted on walls, ceilings, or corners
Available in a variety of sizes and colors

Use Cases:

Home studios
Professional recording studios
Home theaters
Offices
Schools
Churches
Other spaces where acoustic performance is important

Installation & User Guide

Auralex® Acoustics, Inc.

1-800-959-3343 | 317-842-2600 | Auralex.com

9955 Westpoint Drive, Suite 101, Indianapolis IN USA 46256

Studio6™

1343-1015.Studio6 User Guide (01/13/2020 - 10:37 AM)

Tubetak Pro™ Liquid Adhesive

• Cut the tip off of the threaded nozzle feature on the front of the cartridge, close

to the threads, and screw the nozzle onto the cartridge. Cut 1” off the tip of the

Tubetak Pro nozzle for a large size opening and at an angle.

• Apply Tubetak Pro to the mounting surfaces of the Studio6 and wall, gently

flatten the bead using a putty knife.

• For best adhesion, carefully press your foam into place, applying moderate

pressure for a minimum of 15 seconds to spread out the adhesive. Separate the

foam from the wall for 2 to 5 minutes then reassemble with firm pressure.

• When adhesive is ready, align the Studio6 panel at the desired location

and firmly press in place.

Stand Mounting

• Set up the stand and firmly tighten

the pole into the base. Remove the

star washer (if present) from the top

of the stand. Extend the top tube and

firmly tighten the adjustment collar.

• Remove waste from center of the

Studio6 creating a hole for the stand.

Bend along the mid-line, face down

on the edge of a table or counter.

Reach into the gap and pull out the

tube shaped piece of foam.

• Insert tube of stand into the hole

in the center of the Studio6 panel

(assistance is recommended). Adjust

to desired height.

Thank you for purchasing Auralex® Studio6™ Bass Traps.

• Prior to mounting, mark desired panel locations on the wall with small pencil marks or masking tape.

• Clean the attachment points on the wall surface with isopropyl or denatured alcohol, wipe gently and let dry.

Avoid household cleaners, as their surfactants will degrade the bonding power of the adhesives.

• Adhesive will be applied to the rear surface or rear miter of the Studio6 for wall and corner applications, respectively.

Studio6 shown on stand

Studio6 with waste removed

NOTES:

Tubetak Pro is considered a permanent installation. Removing a panel after the

adhesive has cured can result in some damage to the Studio6 and the mounting

surface.

Auralex is not responsible for any damage to walls, floors, ceiling or the overall

structure that occurs doing installation or removal of our products.

Try using a flat edge knife to carefully scrape the panel away from the wall to minimize

tearing, and then use a citrus-based adhesive remover.

ADHESIVE WALL MOUNTING ADHESIVE CORNER MOUNTING

Figure 1.

Apply Adhesive

or here for wall

mounting.

Apply Adhesive on the

two rear bevels for

corner mounting.

Auralex Studio6™ User guide

Brand: Auralex

Model: Studio6™

Type: User guide

Auralex Studio6™

Auralex® Studio6™ Bass Traps are designed to improve the acoustic performance of your room or studio. They can be used to reduce standing waves, flutter echoes, and other acoustic problems.

Features: