Pottinger VITASEM 252 A Operating instructions

Operator‘s manual

GB

+ INSTRUCTIONS FOR PRODUCT DELIVERY . . . Page 3

"Translation of the original Operating Manual" Nr. 99 8622.GB.80Q.0

Seed drill

VITASEM A 252

(Type 8621 : Chassis-Nr: + . . 01180 / MaschNr: + . . 02180)

VITASEM A 302

(Type 8622 : Chassis-Nr: + . . 02451 / MaschNr: + . . 03451)

VITASEM A 402

(Type 8623 : Chassis-Nr: + . . 01099 / MaschNr: + . . 02099)

1500_GB-PAGE 2

Product liability, information obligation

Product liability obliges manufacturers and dealers to issue operating instructions for the machine at the point of sale and to instruct

the customer on the operation, safety and maintenance regulations governing the machine.

A confirmation is required to verify that the machine and operating instructions have been handed over correctly.

For this purpose

- Document A is to be signed and returned to Pöttinger or via the internet to www.poettinger.at

- Document B remains with the specialist dealer handing over the machine.

- The customer receives document C.

For the purposes of product liability law, every farmer is an entrepreneur.

In the terms of product liability law, damage to property is any damage arising due to the machine, but not to the machine, and an

excess (500 euros) exists for this liability.

Corporate damage to property within the terms of the product liability law is excluded from this liability.

Be advised! The operating instructions must also be handed over with any subsequent machine sale or transfer and the transferee

must be instructed in the regulations stated.

Pöttinger - Trust creates AfÀ nity - since 1871

"Quality pays for itself." Therefore we apply the highest quality standards to our products which are constantly monitored by our

in-house quality management and our management board. Because the safety, perfect function, highest quality and absolute

reliability of our machines in operation are the core competencies for which we stand.

There may be deviations between these instructions and the product as we are constantly developing our products. Therefore no

claims may be derived from the data, illustrations and descriptions. Please contact your Specialist Service Centre for any binding

information about specific features of your machine.

We would ask you to please understand that changes to the scope of supply with regard to form, equipment and technical

specifications are possible at any time.

Any form of reprint, translation or reproduction, including excerpts, requires the written approval of Pöttinger Landtechnik GmbH.

All rights according to copyright laws remain expressly reserved by Pöttinger Landtechnik GmbH.

Refer to PÖTPRO for additional information about your machine:

Are you looking for suitable accessories for your machine? No problem! All the information you require is here at your disposal.

Scan the QR code on the machine's type plate or look under www.poettinger.at/poetpro

And if we don't have what your looking for, then your Specialist Service Centre is there for you with help and advice.

Dokument D

GB-0600 Dokum D Anbaugeräte - 3 -

PÖTTINGER Landtechnik GmbH

Industriegelände 1

A-4710 Grieskirchen

Tel. 07248 / 600 -0

Telefax 07248 / 600-2511

T Machine checked according to delivery note. All attached parts removed. All safety equipment, drive shaft and operating

devices at hand.

T Operation and maintenance of machine and/or implement according to operating instructions explained to the customer.

T Tyres checked re. correct pressure.

T Wheel nuts checked re. tightness.

T Drive shaft cut to correct lenght.

T Correct power-take-oɈ speed indicated.

T Fitting to tractor carried out: to three-point linkage

T Trial run carried out and no defects found.

T Functions explained during trial run.

T Pivoting in transporting and operating position explained.

T Information given re. optional extras.

T Absolute need to read the operating manual indicated.

Please check. X

According to the product liability please check the above mentioned items.

INSTRUCTIONS FOR

PRO DUCT DELIVERY

GB

In order to prove that the machine and the operating manual have been properly delivered, a confirmation is necessary.

For this purpose please do the following:

- sign the document A and send it to the company Pöttinger or via the internet to www.poettinger.at

- document B stays with the specialist factory delivering the machine.

- document C stays with the customer.

- 4 -

1500_GB-INHALT_8622

CONTENTS GB

Picture instrction: (13/1) means fig. 13, Position 1

Table of contents

SAFETY

Safety advice .............................................................6

DESCRIPTION OF SERVICES

Overview .................................................................... 7

Versions .....................................................................7

WARNING SIGNS

CE sign ......................................................................8

Warning Signs (symbols) ...........................................8

Meaning of warning signs..........................................8

TECHNICAL DATA

Brief description of implement ................................10

Technical data ..........................................................10

Equipment ...............................................................11

Additional safety information for VITASEM A ..........11

Additional equipment...............................................11

Use of the drill as intended ......................................12

Position of identification plate .................................12

TRACTOR REQUIREMENTS

Tractor ......................................................................13

Ballast weights ........................................................13

Lifting gear (three-point linkage) ..............................13

Required hydraulic connections ..............................13

Necessary power connections ................................13

MOUNTING AND DISMANTLING

Loading .................................................................... 14

Attaching .................................................................14

Mounting with mechanical upper link ......................14

Detachment with hydraulic upper link .....................15

Transport position ....................................................15

PUTTING INTO OPERATION OF CONTROL

UNIT

Connecting control parts .........................................16

Compass terminal....................................................16

Power Control and Isobus Terminal.........................16

COMPASS TERMINAL

Performance features of the terminal ......................17

Initial operation ........................................................18

COMPASS terminal .................................................18

Displays and functions ............................................18

Calibration (standard) ..............................................21

Calibration (electrical seed amount adjustment) .....22

Basic setting ............................................................23

Alarm messages ......................................................30

Examples for setting tramlines ................................31

ARTIS CONTROL SYSTEM

Control console .......................................................32

Function of the keys ................................................33

Menus .....................................................................34

Work menu ..............................................................34

SET menu ...............................................................36

1. Seed library ..........................................................36

1.1 Edit seed ............................................................37

1.1.1 Change screen................................................37

2. Calibration ...........................................................38

3. Tramline switching ...............................................40

4. Predosing parameters .........................................41

5. Alarms ..................................................................42

6. Emergency operation "Manual dosing" ...............42

7. 100-metre comparison ........................................43

Data Menu ...............................................................44

Sensor Test Menu ...................................................46

Configuration menu .................................................47

System Menu ...........................................................48

Alarm and warning messages ................................49

Notes: ......................................................................51

ISOBUS - TERMINAL

Control console .......................................................52

Menu items in the Start menu .................................52

Functions in WORK menu ......................................53

Settings in SET menu ..............................................55

1. Seed library ..........................................................56

1.1 Alter seed setting ...............................................56

2. Calibration ...........................................................57

3. Tramline switch ....................................................59

4. Predosing parameters .........................................61

5. Alarms ..................................................................61

6. Emergency operation "Manual dosing" ...............62

7. 100-metre calibration ..........................................62

8. Adapting the work menu .....................................63

Functions in the DATA menu....................................63

Functions in TEST menu..........................................65

Configuration menu .................................................66

Alarm and warning messages ................................67

Note .........................................................................69

OPERATION

Notes for operation ..................................................70

Hectare counter ......................................................71

Loading ramp ..........................................................71

Filling seed hopper ..................................................72

Emptying seed hopper ............................................73

Cleaning seed hopper .............................................74

Setting of rest quantity monitoring ..........................74

Seed box cover .......................................................75

DOSING

Combined sowing wheel .........................................76

Large seed wheel .....................................................76

Fine sowing wheel ...................................................76

Dosing......................................................................77

Instructions for overseeding (optional) ....................77

Grain test for oversowing ........................................78

Adjusting the sowing rate ........................................79

1. mechanical dosing ...............................................79

2. electric dosing .....................................................79

Possible settings .....................................................80

Gear position ...........................................................80

Rate reduction / normal gear position .....................80

Switching undersowing / oversowing ......................80

Gearwheels .............................................................. 81

Cut-off slide .............................................................81

Bottom flap ..............................................................82

Covers (additional equipment) .................................82

Reduction insert ......................................................83

Agitator shaft ...........................................................84

Turning agitator shaft ...............................................84

Oscillating agitator shaft ..........................................85

- 5 -

1500_GB-INHALT_8622

CONTENTS GB

CALIBRATION

Set spread rate with the help of the calibration

test ........................................................................... 86

LANDWHEEL

Functional principle .................................................89

COULTER PRESSURE

Coulter pressure adjustment ...................................90

Pressure roller ..........................................................90

ELECTRIC METERING

Electric metering ......................................................91

Functioning of electric metering ..............................91

ROW MARKER

Row marker .............................................................92

HARROW TYPES

Harrow types ...........................................................93

TRAMLINES

Setting up tramlines .................................................94

Tramline types..........................................................94

Adjusting the implement ..........................................94

Switching tramline ...................................................96

Tramline marker .......................................................97

SEED RATE ADJUSTMENT

Electric seed rate adjustment ................................98

TRANSPORT

General Transport Instructions ................................99

MAINTENANCE

Safety point ...........................................................100

General maintenance hints ....................................100

Cleaning of machine parts .....................................100

Parking in the open ................................................100

Winter storage .......................................................100

Drive shafts ............................................................100

Hydraulic unit .........................................................100

Maintenance ..........................................................101

Care of the electronic components .......................106

Protecting the electrical system ............................106

SERVICE

Assignment diagram ..............................................107

Terminal diagram optional extra special

tramlines ................................................................108

Job computer electrical dosing device .................109

Terminal assignment of Compass terminal: ..........110

Terminal assignment of power control terminal: ....111

Terminal assignment of CCI terminal: ....................112

Power drivers: ........................................................114

Cable harness ........................................................115

Cable for lifting gear signal ....................................119

Battery cable .........................................................120

Tractor cable ..........................................................121

SUPPLEMENT

Combination of tractor and mounted implement ..126

SOWING TABLES

Sowing tables ........................................................129

Grain test (for oversowing) ....................................130

Shutter slides position ...........................................131

Sowing table VITASEM (normal dosage) ...............132

Sowing table VITASEM (normal dosage) ...............133

Sowing table VITASEM (normal dosage) ...............134

Sowing table VITASEM (normal dosage) ...............135

Sowing table VITASEM (normal dosage) ...............136

Rapeseed (normal dosage) ....................................137

Sowing table VITASEM (electrical dosage) ............138

Sowing table VITASEM (electrical dosage) ............139

Sowing table VITASEM (electrical dosage) ............140

Sowing table VITASEM (electrical dosage) ............141

Sowing table VITASEM (electrical dosage) ............142

Sowing table VITASEM (electrical dosage) ............143

Sowing table VITASEM (electrical dosage) ............144

- 6 -

1300-GB-SICHERHEIT_8521

GB

SAFETY

Safety advice

Set the tractor lifting hydraulic system to "Floating position" prior to any hitching and unhitching!

No persons may stand between the tractor and implement during hitching and unhitching; do not enter

the hazard area between tractor and implement when operating the hydraulic system external control!

Danger of injury!

Check that the drilling machine (with folded in track markers) does not touch the tractor when raising.

– e.g. at projecting rear window!

Ensure sufficient steering safety - if the seed hopper is full and particularly as combination; attach

corresponding front weights to the tractor!

Check the tractor and implement for operational and traffic safety every time before they are put into

service! The safety devices must be attached!

The user is responsible for safety!

Do not transport with the seed hopper full!

Climbing onto and riding on the implement (including loading ramp) and remaining in the hazard area

(swivel zone) are not permitted!

Lower the implement, switch off the engine and remove the ignition key before leaving the tractor!

Only perform adjustment and maintenance work with the implement lowered!

Do not reach into the seed hopper and do not place any objects in the empty box, because at gear setting

> “0” any stirring shaft present will turn if the implement is moved; danger of damage and breakage!

When filling dressed seed and cleaning using compressed air, protect parts of body appropriately - the

dressing is irritant or poisonous!

Ensure that there are no persons near the implement before starting up or operating the implement!

On steep slopes (in contour line), take the position of the centre of gravity into account with hydraulic

front drilling machine (combination)!

Prior to first use and after a long period out of use, check the oil level in the transmission and all bearings

for sufficient lubrication; check the tight fit of all bolts. (leakproofness of the hydraulic system) and tyre

pressure!

You should read these Operating Instructions and the safety information ("For your safety") carefully and take heed of

them before taking the drilling machine into service; this includes the instructions for a combined cultivating unit.

The person operating the machine must be qualified regarding the use, maintenance and safety requirements and be

informed about the hazards. Pass all safety instructions on to other users.

The relevant accident prevention regulations as well as the other recognised safety, occupational health and road traffic

regulations are to be observed.

Pay attention to the "Warning signs"!

Notes in these Instructions with this symbol and warning signs on the unit indicate hazards! (See

Attachment "Pictogram symbols" for explanation of the warning signs".)

Loss of warranty

The drilling machine is only constructed for customary agricultural use.

Any other use is deemed not as intended and no liability is assumed for any damage resulting from such use.

Use as intended also includes the observance of the specified operating, maintenance and repair conditions as well as

the sole use of original spare parts.

Use of any accessories and/or parts from other manufacturers (wearing and spare parts) that have not been approved

by PÖTTINGER leads to lapsing of any warranty.

Unauthorised repairs or modifications to the unit as well as any lack of monitoring during use (... sowing quantity and that

all shares sow!) exclude any liability for damage arising therefrom.

Any complaints on delivery (transport damage, completeness) are to be submitted in writing immediately.

Warranty claims and warranty conditions to be observed or exclusion of liability are as according to our terms of delivery.

0900-GB_ÜBERSICHT_8622

GB

- 7 -

DESCRIPTION OF SERVICES

Overview

Designations:

(1) Row marker

(2) Seed hopper

(3) Gears

(4) Loading platform

(5) Harrow

(6) Coulter system

(7) Rotary Harrow

Versions

Designation DESCRIPTION

A 252 Working width: 250 cm

A 302 Working width: 300 cm

A 402 Working width: 400 cm

1

2

3

4

6

7

5

- 8 -

0900_GB-Warnbildzeichen_8611

GB

WARNING SIGNS

Read operating manual before initial

operation

Observe safety hints

Observe transport and linkage

advice

CE sign

The CE sign, which is affixed by the manufacturer, indicates out ward ly that this machine con forms

to the engineering guideline regulations and the other relevant EU guidelines.

EU Declaration of Conformity (see supplement)

By signing the EU Declaration of Conformity, the ma nu fac tu r er declares that the machine being

brought into service complies with all relevant safety and health requirements.

Recommendations

for work safety

All points referring

to satety in this

manual are

indicated by this

sign.

Meaning of warning signs

Warning Signs (symbols)

Warning signs are used to indicate possible hazards; their purpose is to help ensure the safety of all those involved in

operating the machine.

Replace any missing warning signs.

After initial operation retighten all

screws; furthermore check regularly

for firm fitting.

For special removal torques see

operating manual or spare parts list.

Use torque wrench.

Travelling on implement during

operation and transportation is

not permitted. Use loading plate

or platform only when machine is

mounted and standing dormant, or

when safely supported.

Swivel out side components. Keep

your distance. Do not enter swivelling

range. Ensure sufficient free space

when swivelling out.

Danger of crushing.

Keep your distance

Rotating implements. Keep your

distance. Do not reach in behind

protection devices or covering

plates, etc.

- 9 -

0900_GB-Warnbildzeichen_8611

GB

WARNING SIGNS

Danger from load above. Lift “Vitasem” in bulkhead wall

of seed box. Only use textile belts, no chains.

Put notice here

Do not stand in the area of raised

load.

Never open or remove protection

devices when drives are running.

Keep your distance

Danger from load above. Lift “Vitasem A” seed box

bulkhead wall and transport rings. Use belts. Never lift

drill machine together with agricultural implement.

Legs could be hit through components

suddenly swivelling out or sliding out.

Keep your distance.

- 10 -

1400-GB-TECH DATEN_8622

GB

Brief description of implement

“VITASEM A” are mechanical mounted seed drills supported on the packer roller of the combination implement so that

in use e.g. a PÖTTINGER rotary harrow can avoid stones by moving up.

Mounting and disassembly are facilitated by simple coupling; unhitched the implement rests on four removeable supports.

“VITASEM A” is fitted optionally with trailed, wide or one-disc shares,

“VITASEM A” is fitted optionally with a share replacement system for trailed, wide or one-disc shares.

Driving takes place from the landwheel (both sides, if requested) via a steplessly adjustable dual-range oil bath gearbox

or from an electrical dosage device (optional).

By means of the gearwheels in the gearwheel box you can reduce to half the sowing shaft rotation speed and revert

rotation for overhead sowing.

The sowing shaft can be switched off at the right half.

The special feature of the “VITASEM A” drills is that normally with undersowing with its multi-sow wheels and when set

up for overhead sowing (on request) it can for example dose rapeseed grains individually by changing the direction of

rotation of the sowing shaft.

Easy handling and reliability in use are ensured e.g. by the rainproof seed hopper cover , functionally shaped seed hopper,

funnel outlets to each metering wheel, fill level indicator, central coulter pressure adjustment and easy calibration with a crank.

There is a range of equipment available to adapt the “VITASEM A” to vastly differing conditions: e.g. various harrow versions,

hydraulically switchable and lifting track markers, electronic tramline switching incl. hectare counter and calibration aid,

remaining amount sensor and sowing shaft control, tramline marking, hydraulic coulter pressure adjustment, agitator

shaft for grass seed etc.

TECHNICAL DATA

Technical data

* Observe the transport width of the tillage implement! (Subject to alteration)

VITASEM 252 A 302 A 402 A

Working width [cm] 250 300 400

Transport width approx. [cm] 250 * 300 * 400 *

Seed hopper outlets 21 25 33

Number of rows: Standard [Option] 20 [14, 16] 24 [16, 20] 32 [22, 26]

Row interval [cm] 12.5 / 18.3 / 15.8 12.5 / 19.2 / 15.1 12.5 / 18.5 15.5

Weight[kg] (excluding accessories)

.. with trailed shares 720 kg

810 kg 1100 kg

.. with one-disc shares 750 kg

840 kg 1150 kg

Seed hopper content [l] (hopper, large) 480 600 (1000) 850 (1400)

Fill height approx. [cm] 161 161 / 180 161 / 180

Filling opening [cm] 200 x 62 250 x 62 350 x 62

Share increment [cm] 30

Disc share Ø [mm] 320 x 3

Pressure roller Ø [mm] 250 x 40

Coulter pressure / share [kg] 25

Oil-submerged transmission fill amount 2.5 l (hydraulic oil HLP 32)

Sound pressure level 70 dB(A)

- 11 -

1400-GB-TECH DATEN_8622

TECHNICAL DATA GB

Equipment

· Trailed or one-disc share

· For trailed and wide sowing share, optional equipment

with one-disc shares

· Seed hopper with content indicator and flap cover

· Drive landwheel

· Steplessly adjustable two-section oil-submerged

transmission

· Multi-sowing wheel with reducing inserts

· Fine metering wheel

· Sowing shaft can be switched off at one half

· Calibration device with crank and emptying trough

· Central coulter pressure adjustment

· Removeable supports for dismantling/placing down

Additional equipment

· Hitching set for set-up; approx. 35 kg

· Device for overhead sowing (e.g. rapeseed)

· Coulter harrow; approx. 0.6 kg/share

· Drill harrow, 2-part with trailed tines; approx. 17 kg/m

· Harrow extension for side cover; approx. 3 kg

· Perfect harrow with individual spring-mounted elements;

approx. 22 kg/m

· Transport tine protection for Perfect harrow

· Disc track marker secured against break off and with

hydraulic lifting; approx. 60 kg

· Hydraulic hose extension 0.5m and 1.6m

· Electronic tramline switching with sowing wheel stop- for

2 or 3 rows per track - including hectare counter and

calibration aid function.

· Remaining amount and sowing shaft monitoring (only

in combination with tramline switching)

· Battery connection cable

· Control cable 2m, 4m, 7m as extension on implement

combination

· Disc tramline marking (only with tramline switching and

loading ramp); approx. 35 kg

· Hydraulic coulter pressure adjustment

· Agitator shaft - rotating or oscillating

· Sowing unit cover - for outlets not in use

· Hectare counter (mechanical)

· Packer roller for trailed shares

· Packer roller for one-disc shares

· Second landwheel right for 3 m and 4 m implement

width; approx. 50 kg

· Hydraulic landwheel lifting

· Electrical seed adjustment

- electrical dosage

- radar sensor for electrical dosage

- Isobus terminal CCI100 for electrical dosage

Additional safety information for VITASEM A

• Do not reach into the rotating agitator shaft

• Observe the safety distances in all maintenance and adjustment work on the implement; rotating and oscillating

mechanical parts pose a risk.

• Only use treads to fill the seed hopper. Riding on the implement is not permitted.

• Driving on public roads:

- Observe the official regulations of your country.

- Driving on public roads may only be performed as described in the chapter "Transport position".

- Block all hydraulic circuits.

- Do not place any objects in the seed hopper - the agitator shaft also rotates during manoeuvering

• Protection devices must be in proper condition.

• Before travelling bring all swivelling parts into their correct positions and secure against dangerous changes to position.

• Check that lighting functions before travelling.

- 12 -

1400-GB-TECH DATEN_8622

TECHNICAL DATA GB

Position of identification plate

The chassis number is engraved on the type plate shown

at the side. Warranty claims, enquiries and spare part

orders cannot be processed without the chassis number.

Please enter the name on the title page of the Operator's

Instructions immediately upon taking delivery of the vehicle

/ implement.

Use of the drill as intended

The "Vitasem A (Type 8621, 8622 and 8623)" drill is only intended for customary use in agricultural work.

• To sow seed

• Any use beyond this (e.g. spreading road salt or grit) is not use as intended.

The manufacturer accepts no liability for any damage arising as a result thereof; the user accepts sole responsibility.

• The observance of operating, service and maintenance requirements laid down by the manufacturer is also included

in "defined use“.

- 13 -

1400_GB-SCHLEPPERVORAUSSETZUNG_8622

GB

TRACTOR REQUIREMENTS

Tractor

The following tractor requirements are necessary for the operation of this machine:

- Tractor power: from 90 KW (in combination with a rotor harrow, depending on the rotor harrow)

- Hitching: Lower link Cat. II

- Connections: see Table "Hydraulic and electrical connections required"

Ballast weights

The front of the tractor is to have sufficient ballast to guarantee

braking and steering capabilities.

At least 20% of the tractor’s tare weight on

the front axle!

Lifting gear (three-point linkage)

- The tractor’s lifting unit (three-point linkage) must be

designed for the load that occurs. (See technical data)

- The lifting struts are to be set at the same length (4)

using the relevant adjusting equipment

(See the tractor manufacturer’s operating manual)

- Select the rear position if the lifting rods can be adjusted

in various positions on the lower link. This relieves the

pressure on the tractor’s hydraulic system.

- The limiting chain or lower link stabilisers (5) are to

be set so that the coupled implement CANNOT move

sideways. (Safety measure for transportation)

Required hydraulic connections

Design Consumer Hydraulic connection Identification (on

the implement)

Standard Track marker Single-action with floating position

Hydraulic upper link (variant) Dual-action

Option Hydraulic regulator of harrow pressure Single-action

Necessary power connections

Design Consumer Pin Volt Power connection

Standard Lighting 7-pin 12 V DC According to DIN-ISO 1724

Compass control 3-pin 12 V DC per DIN-ISO 9680

Optional Electric metering 3-pin 12 V DC per DIN-ISO 9680

ISOBUS According to DIN-ISO 11783

20%

Kg

371-08-16

- 14 -

1600-D MOUNTING AND DISMANTLING_8622

GB

MOUNTING AND DISMANTLING

Loading

Be advised!

Do not stand underneath the lifted

implement!

1

The drill with the seed hopper open is to be fastened

at the round bar (1) with 2 lugs on the loading ramp for

crane loading.

Only lift separately with empty seed hopper (without tillage

implement).

Observe load-bearing capacity of straps.

Manoeuver carefully and ensure balance.

Attaching

Vitasem A series is designed for hitching onto Pöttinger

rotary harrow packers of the series Lion, compact corners

of the series Fox or for a rotary harrow packer with the

same conditions.

Be advised!

Risk of crushing!

Instruct all persons to leave the hazard

area when approaching the drill with

the tractor!

Secure the tractor against accidental

rolling when attaching and removing

the seed drill!

Only activate the tractor’s lifting

hydraulics if there is no-one in the

hazard area between the tractor and the

seed drill!

Note:

Compatibility is to be checked before

fitting the drill to a non-Pöttinger rotary

harrow!

The drill is fixed at the rotary harrow packer and guided

via the upper link.

Hitching onto rotary harrow packers of the same

make

, see the instruction manual of the respective rotary harrow

packer.

Hitching onto an external rotary harrow packer

The ideal attached height for an external rotary harrow is

679mm / 663 mm

Mounting with mechanical upper link

Be advised!

Risk of crushing! Only detach the

emptied drill on firm and even parking

areas. The drill is placed on 4 support

feet. It must have sufficient stability.

1) Detach drill from rotary harrow:

- Raise the rotary harrow

- Place the rear support feet in the holder and fasten

- Lower the rotary harrow until the upper link can be

moved freely

- Detach upper link

- Raise the rotary harrow

- Place the front support feet in the holder and fasten

- Open the clamps of the connecting element holders

- Lower the rotary harrow

- Close hydraulic lines to tractor

- Close off cable of Compass control unit.

- Close off cable of lighting at tractor.

- 15 -

1600-D MOUNTING AND DISMANTLING_8622

MOUNTING AND DISMANTLING GB

2) Set the rotary harrow for operation without drill:

A

- Raise the rotary harrow

- Insert the auxiliary bolt (parking position is on the

levelling bar) into the auxiliary hole of the roller (A)

(eases removal of the pivot bolt)

- Lower rotary harrow and attach pivot bolt

- Raise the rotary harrow and remove the auxiliary bolt

and insert in the parking position provided

Detachment with hydraulic upper link

1. Raise the drill with the control unit at the tractor

2. Fit support feet at the back and secure with linchpins

3. Lower the drill with the control unit at the tractor until

the hydraulic upper link is tensionless.

1

2

4. Remove bolt (1)

5. Swivel hydraulic upper link (2) back and secure in

swivelled back position with the bolt (1).

3

4

6. Open connection bars (3) on both sides (left and right)

Caution:

Risk of damage to the implement

Do not insert bolt (4) of the connecting bar

in the hole plate at the parallelogram. This

may lead to bending of the parallelogram.

7. Fit support feet at front and secure with linchpins

8. Lower rotary harrow

9. Remove rotary harrow

10. Fit connecting bar (3) at original position.

Transport position

The tractor and implement must conform to national road

traffic regulations and accident prevention regulations when

driving on public roads and paths.

The vehicle owner and operator are responsible for the

observance of statutory regulations.

The general safety provisions in the Attachment to these

Operating Instructions are to be observed.

Be advised!

Riding the seed drill is not permitted!

- Only transport with empty seed hopper

- Close seed hopper cover

- Securely lock emptying trough in top position

- Fold up foldable tread and secure

- Fold in track marker and secure

- Fold in landwheel and secure

- Fold up tramline marker and secure

- 16 -

1400_GB-INBETRIEBNAHME_STEUERUNG_8622

GB

PUTTING INTO OPERATION OF CONTROL UNIT

Connecting control parts

Depending on the tractor and the attached implement, use the following connection options for control parts

Compass terminal

For operation control: Connect the connection cable of

the attached implement (1) to the connection cable of the

terminal (2).

For power supply, connect the power cable of the terminal

(3) to the tractor's 3-poles socket.

VITASEM

15A

1

2

3

Power Control and Isobus Terminal

Option 1

The tractor is equipped with ISOBUS.

For operation control and power supply connect the

connection cable ISOBUS of the attached implement (1)

directly to the tractor ISOBUS socket.

VITASEM

1

Explanation

1 ISOBUS connection cable of the implement

2 Tractor cable

3 Power supply connection on tractor

4 Control unit connection

5 Battery cable

Option 2

The tractor is not equipped with ISOBUS, but with a power

socket.

A tractor cable (2) is necessary. For power supply, connect

the tractor cable plug (3) to the tractor 3-poles socket.

For operation control connect the tractor cable plug (4) to

the control unit.

Connect the ISOBUS cable of the attached implement (1)

to the tractor cable (2).

VITASEM

2

1

4

3

Option 3

The tractor is not equipped with ISOBUS, no power socket

is available, or it is not sufficiently secured, or the power

supply is insufficient.

A battery cable (5) is necessary. (This battery cable can be

obtained from Pöttinger spare parts warehouse) For power

supply connect the battery cable (3) to the tractor battery.

For operation control connect the battery cable plug (4)

to the control unit.

The ISOBUS cable of the attached implement (1) is

connected to the battery cable (5).

VITASEM

1

5

4

3

4

- 17 -

1600_GB-Compass-Terminal_8611

GB

COMPASS TERMINAL

Performance features of the terminal

Connection to power

The terminal’s electricity is supplied via a plug connection (in accordance with DIN 9680) to the tractor’s 12 V on-board

electrical system,. These three-pin plugs may also be two-pin versions as only two main wires (+12 V, ground) are required.

Be advised!

Other plug and socket designs are not permitted otherwise functional reliability cannot be guaranteed.

Technical data

Operating voltage: +10V ...... +15V

Operating temperature range: -20°C +60°C

Storage temperature: -30°C +70°C

Degree of protection: IP65

Fuse: 15A fuse in operating voltage plug.

LCD display: backlit

Be advised!

The terminal is to be protected from the wet and the cold! The terminal is not intended for storage

outside!

Usable functions

The Compass terminal is a compact on-board computer with many useful functions. It performs important control and

monitoring tasks and makes your work easier with display and auxiliary functions.

Overview of usable functions:

Control functions:

- Setting tramlines

- Additional setting of tramline marking

- Manual or automatic switching of the drive-through counter e.g. by means of the track marker shuttle valve, signal

socket or tailwheel sensor or transmission signal

- Interruption of the automatic switching of the drive-through counter (when driving around obstacles)

- Regulating the Spread rate (optional extra)

Display functions:

- Through-drive counter and tramline cycle display

- Part area hectare counter

- Total area hectare counter

- Driving speed

- Sowing shaft speed

- Current distribution rate

Monitoring functions:

- Sowing shaft monitoring

- Fill level monitoring

Auxiliary functions:

- Sensor test

- Calibration aid to calculate and count the number of crank turns

- Adjustable delay for the automatic switching of the drive-through counter

- Optional menu guide in several languages

- 18 -

1600_GB-Compass-Terminal_8611

COMPASS TERMINAL GB

Display driving speed (a)

Press once = Display driving speed (in km/h)

a Driving speed (in km/h

b Tramline symbol: A tramline is being set up if the tramline symbol is displayed.

Display hectare counter (5)

press 1x = display daily hectare counter

press 2x = display yearly hectare counter (designated with the mark "∑")

press 3x = total counter (not deletable, recognisable by the black background of the

number)

delete daily or yearly hectare counter = press for 3 seconds resp. until you hear

the signal tone

a Hectare counter

b Tramline symbol: A tramline is being set up if the tramline symbol is displayed.

Displayrotations (8)

Press once = display sowing shaft speeds (in rpm)

Initial operation

The Compass terminal is switched on with the key. The set machine type and software version appear in the display

for approx. 3 seconds, then the speed display appears.

The Compass terminal is switched off with the key (depress for 3 seconds).

Before initial operation, check and adapt the correct basic setting (machine type, language, ..).

COMPASS terminal

The user interface of the Compass terminal

(0) Display

(1) Menu

(2) Spread rate

(3) Tramline

(4) Calibration

(5) Driving speed

(6) Hectare counter

(7) Arrow down

(8) Arrow up

(9) I/O

(A) Power supply connector (fuse 15 A)

(B) Parallel plug for data transfer

Operating notes

To navigate and change the setting values

To save, press key for 2 seconds or until signal tone is heard.

To move to a menu level without saving, press key briefly

To leave the submenu without saving

Displays and functions

0,0 km/h

a

b

0,23 ha

a

b

0

123

654

789

AB

- 19 -

1600_GB-Compass-Terminal_8611

COMPASS TERMINAL GB

Display Tramline step and drive-through counter (7)

press 1x = current tramline step and drive-through counter.

a Tramline type and tramline step

b Symbol flashes when the driving speed is detected.

Note:

If the symbol does not appear, this indicates a defect.

The power-train and/or sensors are to be checked.

c Drive-through counter: counts the line passing-throughs automatically as soon

as the implement is set down from headland position. In the Settings menu you

can select from 4 options based on which these will be switched on.

d The field symbol indicates where work commenced on the field.

Start work left/ Start work right

e Display "Tramline is being set up!" This notification is displayed when a tramline

is supposed to be created during a line passing-through.

Note:

The notification "Tramline is being set up!" appears immediately

after switching on the drive-through counter.

The creation of the tramline as such begins only when the speed

has exceeded 1 km/h.

Operation:

Tramline tact can be changed manually using the arrow keys .

Key

Press for 2 secs.

=

The drive-through counter is reset to start value 1.

Press twice = STOP appears on the screen; counting is paused and the current value is saved (e.g. avoid

an obstacle). Press again = counting restarts with the saved value.

Displayspread rate (6)

Press once = Displays the set spread rate and gear setting (prerequisite: the

calibration was performed)

a current spread rate

b Spread rate in percentage of the calibrated value

c Gear setting

d Display: "Tramline is being set up!"

Optional equipment: electrical seed setting

The seed amount can be changed with a pre-set increment (%) using the arrow

keys .

Repeated actuation of keys is possible.

The spread rate values and the gear setting are updated automatically.

Note:

The minimum spread rate increment is 0.1 kg/ha. Because

the spread rate is rounded, it is possible that for low spread

rates you arrive at step changes (%) due to rounding.

The increment (%) can be set in the Settings menu - Seed.

Saatmengen-

verstellung

240,0 kg/ha

Saatmengen-

verstellung

100% G:77

a

bc

d

asym. 8

akt. 1

a

bc

d

asym. 8

akt. 1

e

110%

- 20 -

1600_GB-Compass-Terminal_8611

COMPASS TERMINAL GB

The crank symbol on the display shows the number of times the crank must be turned to set the new gear setting!

If the spread rate is not equal with the nominal value set at calibration (=100%), when you start off, you will see an indi-

cation for about 3 seconds that signals the modified spread rate. The indication appears every time when you start the

engine and shows the percent value of the nominal spread rate with which you sow at the moment.

To turn off the indication, reset the spread rate to 100% with the help of the arrow keys.

Page is loading ...

Pottinger VITASEM 252 A Operating instructions

This manual is also suitable for

Pottinger VITASEM 252 A Operating instructions

Related papers

Other documents