Lightolier IS:2000LVNT User manual

Brand: Lightolier

Model: IS:2000LVNT

Type: User manual

INSTRUCTION SHEET NO

INSTRUCTIONS PROCEDURE FOR LOW VOLTAGE

FRAME=fN KIT WITH REM~E TRANSFORMER

IS:2000LVNT

0191

Page 1 of 2

READ AND UNDERSTAND THESE INSTRUCTIONS BEFORE INSTALLING FIXTURE.

This fixture is intended for installation in accordance with the National Electrical Code or local regulations. To

asaure full compliance with local codes and regulations,

check with your local electrical inspector before

installation. To prevent electrical shock, turn off electricity at fuse box before proceeding.

Retain these instructions for maintenance reference

N~E FRAME-fN KIT IS PROVIDED WITHOUT TRANSFORMER. TRANSFORMER MUST BE PROVIDED SY

OTNERB. LIGHlOLIER CAT #B60S AND 8609 TRANSFORMERS MAy BE USED.

CAUTION: THIS FRAME-IN KIT IS RATED AT 42VA. USE ONLY 12V. AC. INPUT.

FIG. A

FIG. B FIG. C

FIG. D

1. FRAME-IN

2. CLOSE-IN

3. SNAPON

4. PUSH-UP

WARNING—(RISK OF FIRE) DO NOT INSTALL INSULATION WITHIN 3 INCHES OF FiXTURE SIDES OR

WIRING COMPARTMENT, NOR ABOVE FIKTURE IN SUCH A MANNER TO ENTRAP HEAT.

FRAME.IN (Fig. A)

Faaten MOUNTING FRAME to wood joist. Line

N~E For wat plaster ceiling, uae Plaster

Ring Accessory No. 1959 (order aaparately).

4&=---- ‘OTO”cL’p

SNAPIN (Fig. C).

SEE SEPARATE

REFLECTOR TRIM

PUSH-UP (Fig. D).

INSTRUCTION

SHEETS.

FIG G

SEE BACK PAGE FOR LAMPING INSTRUCTIONS.

LK59-ITC>949

[=@sEcAucus> NEw JERSEY,07096

* MO NT REAL, QUEBEC, C AN ADA

~&OOOLVNT

LAMPING

Page 2 of 2

NOTE Socket manufacturers have suggested that

socket may fail after 3 to 6 relampings. If this

occurs socket can be replaced by disconnecting

male connectors (attached to socket leads) from

female connectors (attached to fixture leads) and

1. Make sure that power is OFF when Iamping

or relamping. Remove LAMP RING from

SOCKET CUP by pulling etraight down.

2. Ineeft LAMP @fR-16) between LAMP

SPR NGS until face of lamp sits firmly on

GLASS LAMP GUARD (Fig. l).

3, Attach SOCKET to hi-pin prongs on LAMP

replacing it with a naw socket procured thtiugh

Lightolier (Fig H.).

INSULATINGSLEEVING

MALECONNECTORS

(Altaohedto socketWires)

~ FEMALE CONNECTORS

(Attached to

Fixture V4res)

MR16 SOCKET

FIG. H

4. Insert LAMP RING with LAMP and GLASS

LAMP GUARD back into SOCKET CUF!

cf5-’-s0cKET

LAMP

- LAMP SPRING

GLASS LAMP

GUARD

LAMP RING

FIG. I

AIMING ANGLE ADJU=MENT (Fig. J)

1. For vertical adjustment, insert blade of

screwdriver into the open slot of YOKE.

2. Using the screwdriver as a lever, tilt the entire

LAMP HOLDER to the desired angle.

3. ~~L~#mtal adjustment, rotate tie LAMP

OCKET CUP

LAMP HOLDER

NOTE 1. LOW VOLTAGE FIXTURES should be APERTURE TRIM

dimmed only wNh speciel dimmers intended

ASSEMSLY

specifically for that purpose. Use Llghtoller

Lytemode Scenlst,

Crescendo VA, Neptune VA,

Preclslon VA,Esayset VA,Sunriee VA,Redlsnt VA or

equivalent products by others ,or verieblo

sutotranaformera or

electronicdlmmeraintendedfor

~.,

usewith lowvoltageflstuma.2. QWvoltsgefixtures

~.y::,?

mey produoe eudible sound when ueed with

dimme~

which may be objectional in acoustically

critical sreaa.

FIG. J

NOTE Followthe mex. wire length recommended

below to minimize voltsge drop. Voltage drop will

affect the brlghtneaa and color of the light.

Lightolier IS:2000LVNT User manual

Lightolier IS:2000LVNT User manual

Lightolier IS:2000LVNT User manual

Related papers

Other documents