Lightolier IS:1055LV User manual

Brand: Lightolier

Model: IS:1055LV

Type: User manual

INSTRUCTIONSHEETNO.

INSTALLATION PROCEDURE FOR

LOW VOLTAGE

REFLECTOR TRIM IN THE 1000LV FRAME-IN KIT

lS:1055LV

0s90

Page 1

of 2

READ AND UNDERSTAND THESE lNSTRU~lONS BEFORE INSTALLING FIXTURE.

This fixture is intended for installation in accordance with the National Electrical Code and local regulation.

To assure full compliance with local codes and regulations, check with your local electrical inspector before

installation. To prevent electrical shock, turn off electricity at fuse box before proceeding.

Retain these instructions for maintenance reference.

~~%~

FIG. A

FIG. B

FIG. C

FIG. D

1. FRAME-IN

2. CLOSE-IN

3. SNAP~N

4. PUSH-UP

WARNING: BEFORE INSTALLING REFLECTOR TRIM TO FRAME-IN KIT, REAO MARKINGS IN REFLECTOR TRIM

AND ‘IN BOCK~ CUP OF FRAME-IN-KIT TO DErERMINE LAMP WAlTAGE AND TYPE APPLICABLE FOR YOUR

lNBTA1.L&TiON. IF I.C. TYPE FRAMING KIT IS USED, IT MAY BE INSTALLED IN DIRECT CONTACT WITN INSULATED

CSIUNGS. IF A NON I.C. TYPE FRAME4N.KfT IS USED, DO NOT INSTALL INSULATION WITHIN 31NCHSB OF FI)MJRE

SIDE OR WIRING COMPARTMENT, NOR ABOVE FIXTURE IN SUCH A MANNER TO ENTRAP HSAT.

1. FRAME-IN (Fig. A)

See Frame-In Kit Instruction Sheet for installation

procedure.

FRAMINGKIT

,!;;

2. ROTATE ROTO-CLIPS (Fig. B)

MOUNTSFLUSH

ONCEILINGMATERIAL

,..’

As shown in Fig. E.

0“ \

.-.,,:.,--

;’,.’.’.; :.:.-..,

3. SNAP.ON (Fig. C).

, ....:.:

- ... .’$.’.

Insert SOCKET through RECTANGLE HOLE on top

\ ..,-.....-

CEILING

-,:.-...-:.

of REFLECTOR TRIM. Engage TAB from SOCKET

MATERIAL

CUP into one of the SLOTS on top of REFLECTOR

ROTO.CLIP ‘““::;~y ;

POSITION

TRIM and push other end of SOCKET CUP with

:., ,,

LANCING into the other SLOT (Fig. F),

FIG. E

4. PUSH-UP (Fig. D). – SOCKETCUP

Push REFLECTOR TRIM into ceiling until flange

is flueh to ceiling (Fig. D).

RECTANGLEHOLE ~

N~E Socket manufacturers have suggested that

SLOTa

socket may fail after 3 to 6 ralampings. If this

occurs, socket can be replaced by disconnecting

REFLECTORTRIM

male connectors (attached to socket leads) from

female connectors (attached to fixture leads) and

replacing it with a new socket procured through

Lightolier (Fig. G).

INSULATINGSLEEVING

MALECONNECTORa

SEE BACK PAGE FOR LAMP INSTALLATION

(ATTACHEDTO SOCKETWIRE)

AND ADJU~MENT.

FEMALECONNECTORS

(ATTACHEDTO FIXTUREWIRES)

MR16SOCKET

FIG. G

1- I <51“17<> l-l 1= ,a@ :v:::::i,N:r::::,E:i:T:j

LAMPING INSTRUCTIONS AND ADJUSTMENTILOCKING

INSTALL LAMP

Remove LAMP RING from LAMPIYOKE HOLDER by

pulling straight down (Fig. H).

insert LAMP (MR-16) between LAMP SPRINGS until

face of LAMP sits firmly on GLASS LAMP GUARD

(Fig, l).

Attach SOCKET to hi-in prongs on LAMP (Fig. l).

Insert LAMP RING with LAMP and GLASS LAMP

GUARD attached back into LAMP/YOKE HOLDER

(Fig. J).

WARNING: LAMP MANUFACTURERS REQUIRE THE

GLASS IAMP GUARD BE IN PLACE BEFORE ENERGIZING

LAMP AND THAT GREAT CARE MUST BE TAKEN THAT

LAMP IS FULLY COOLED BEFORE RELAMPING. AVOID

FINGER MARKS WHEN HANDLING FOR THEY MAY CAUSE

SHORT LAMP LIFE AND POSSIBLE BREAKAGE.

VERTICAUANGLE ADJUSTMENT AND LOCK (Figd)

9. krserl a screwdriver into the LOCKING GUIDE on the

LAMP/YOKE HOLDER, and locate the clot in the

VERTICAL ADJUST/LOCK SCREW, turn the SCREW

counterclockwise, and using the screwdriver as a

lever, tilt the entwe UMPIYOKE HOLDER to the

desired angle. Once the desired angle ie reached,

tighten screw by turning screwdriver clockwise.

HORIZONTAL ADJUST AND LOCK (Fig. J)

10. The entire IAMPIYOKE HOLDER can be horizontally

rotated to aim the an Ie of light as it leaves the hole

in the APERTURE TRI (Fig. J). This can be done by

backing off the HORIZONTAL ADJUST/LOCK SCREW

one full turn, freeing the SUPPORT PLATE (Fig J).

Grasping the YOKES on either side of the

LAMP/YOKE HOLDER, rotate the SUPPORT PUTE

to the desired angle and lock the position by

tightening the HORIZONTAL ADJUST/LOCK SCREW.

RELAMPING: The locking mechanisms designed within this

fixture allow ralamping without having to readjust and

relock. Follow Steps 5-8.

NOTE 1. LOW VOLTAGE FIXTURES should be

dimmed only with special dimmers Intended

apeclfloslly for that purpose Use Lightoiier

Lytemodej Soenlst, Cresoendo VA, Neptune VA,’

Preolelon VA, Essveet VA, Sunrise VA, Rediant VA or

IS1055LV

0890

Page 2

of 2

fs~

==77=.

LAMP

SPRING

I-44:

GL4S&5L~MP

FIG. H

FIG. I

equlvelant pfidu6te by others or vsrisbie auto.

transformer’e or eieotmnlo dimmers intended for use

with low voltage flxturee. 2. Low voltsge fixtures msy

produoe audible eound when used with externel

dimmem which may be ob]ectional in acoustically

critical eree%

LAMP

GtiG~ARLMP

r LAMP

FIG. J

WARNING: USE ONLY REFLECTOR TRIMS PROVIDED By LIGHTOLIER INC. USE OF ~ER MANUFA~RERS’

RSFLECTDR TRIMS VOIDS THE UNDER~rERS LABORATORIES LISTING AND COULD CONSfTfUTE A FiRE HAZARD.

Lightolier IS:1055LV User manual

Lightolier IS:1055LV User manual

Lightolier IS:1055LV User manual

Related papers

Other documents