Lightolier IS:1062LV User manual

Brand: Lightolier

Model: IS:1062LV

Type: User manual

WARNING: BEFORE INSTALLING REFLECTOR TRIM FRAME4N

KIT, READ MARKINGS IN REFLECTOR TRIM AND ON SOCKET CUP

OF FRAME-IN KIT TO DETERMINE LAMP WAllAGE AND TYPE

APPLICABLE FOR YOUR INSTALLATION. IF I.C. TYPE FRAME-IN KIT

IS USED, IT MAYBE INSTALLED IN DIRECT CONTACT WITH

INSULATED CEILING. IFA NON LC.TYPE FRAME-IN KIT IS USED, DO

NOT INSTALL INSULATION WITHIN 3 INCHES OF FIXTURE SIDES OR

WIRING COMPARTMENT, NOR ABOVE FIXTURE IN SUCH A MANNER

TO ENTRAP HEAT.

READ AND UNDERSTAND THESE INSTRUCTIONS BEFORE INSTALUNG FtXTURE

INSTRUCTION SHEET NO.

This fixture is intendedfor installationin accordancewith the NationalElectricalCode and local

regulations.Toassurefullcompliancewithlocalcafes andregulations,checkwithyourlocalelectrical

inspectorbeforeinstallation.Topreventelectricalshock,turnoffelectricityatfuseboxbeforeproceeding.

IS:1062LV

Retain these instructions for maintenance reference.

0192 Page 1 of 2

INSTRUCTIONS FOR INSTALLATION OF REFLECTOR TRIM 1062LV

IN THE 10OOLVFRAME- IN-KIT

?? s

Fig. A Fig. B Fig. C

Fig. D

1. FRAME-IN

2. CLOSE-IN

3. SNAP-ON

4. PUSH-UP

FRAM-INKIT MOUNTS

FLUSHONCEIUNG

.,. ... :.,- ....

ROTO-CUP

1.FRAME-IN (Fig. A)

POSITION

See Frame-InInstructionSheetfor installationprocedure.

2, ROTATEROTO-CLIPS(Fig. B)

Fig. E

As shownin Fig. E.

3, SNAP-ON (Fig. C)

RECTANGLEHOLE

lnsertSOCKETthrough RECTANGLEHOLEontopof REFLECTORTRIM.

EngageTAB from SOCKETCUP into one ofthe SLOTSon topof

REFLECTORTRIM andpushotherendof SOCKETCUPwith LANCING

intothe other (Fig.F).

4. PUSH-UP(Fig. D)

PushREFLECTORTRIMintoceilinguntilflangeisflushto ceiling(Fig.D).

SLOTS

TRIM

\l (

NOTE: Socket manufacturers have suggested that socket may fail after

3 to 6 relampings. If this occurs, socket can be replaced by disconnect

SOCKET

ing male connectors (attached to socket leads) and female connectors

(attached to fixture leads) and replacing it with a new socket procured

through LIGHTOLIER (Fig, G).

Fig. F

INSULATINGSLEEVING MALECONNECTORS(AllACHED TO SOCKETWIRE)

FEMALECONNECTORS(ATTACHEDTO FIXTUREWIRES)

- ~@MR’’”KH

SEE BACK PAGE FORIAMPING INSTRUCTIONS

Fig. G

1. I es

l“ITC>1.1E R“

i%%wyi!liwn

INSTRUCTION SHEET NO.

IS: I062LV

0192 Page 2 of 2

LAMPING

1.Checkto seathat poweris OFFbefore Iampingor relamping.

2. Removebaffleaperturefrom ELBOWby pullingstraightout (Fig.H).

3. Insertlamp(MR-16bulb) betweenlampsprings.

4.Attach SOCKETto hi-pinprongson LAMP.

5. InsertLAMPRINGwith LAMPand GLASS LAMP GUARD back into ELBOW.

WARNING:

A.LAMPMANUFACTURERSREQUIRETHEGLASS

LAMPGUARDBEIN PLACE

BEFOREENERGIZINGLAMP, AND THAT GREAT CARE MUSTBE TAKEN

THAT LAMP IS FULLY COOLED BEFORERELAMPING. AVOID FINGER

MARKSON INSIDEOFLAMPFORTHEYMAYCAUSESHORT LAMPLIFEAND

POSSIBLE BREAKAGE.

B.USEONLY REFLECTORTRIMS PROVIDEDBY LIGHTOLIERINC. USE OF

OTHERMANUFACTURER’SREFLECTORTRIMSVOIDSTHEUNDERWRfTERS

LABORATORIESLISTINGAND COULD CONSTITUTE A FIRE HAZARD.

w“T ““p

GIASS LAMP

GUARD

~ BAFFLE

Fig. H

APERTURE

NOTE:

1. LOW VOLTAGE FIXTURES should be dimmed only by specialdimmers intended specifically for that purpose. Use Lightolier,

Scenist, Crescendo VA, Neptune VA, Precision VA

EasysetVA,Sunrise VA, Radiant VA, or equivalent products by others or

variable autotransformers or electronic dimmers intended for use with low voltage fixtures.

2. Lowvoltage fixtures may produce audible sound when used with dimmers, which maybe objectionable in acoustically critical areas.

JUNCTIONBOX

[

TRANSFORMER

PRIMARY120V.60

SECONDARY11.4V.

&5W.LOAO

Wwl

3 21/32’

+—---- 5 29/32’ FIANGE DIA.—--+

Fig. I

—

Lightolier IS:1062LV User manual

Lightolier IS:1062LV User manual

Lightolier IS:1062LV User manual

Related papers

Other documents