Whalen BBHC60DBC User manual

THIS INSTRUCTION BOOKLET CONTAINS IMPORTANT SAFETY INFORMATION. PLEASE

READ AND KEEP FOR FUTURE REFERENCE.

Whalen Furniture Mfg., Inc Factory # 7-1564 Page 1

60” High Console

Model # BBHC60DBC

ADULT ASSEMBLY REQUIRED

If you have any questions regarding assembly or if you are missing parts, do not return this item

to the Retailer Store. Please call our toll-free customer service number and have your

instructions and parts list ready to provide the model name, part name or factory number:

1-866-942-5362

Pacific Standard Time: 8:30 a.m. - 4:30 p.m., Monday - Friday

Or visit our web site 24 hours a day, 7 days a week for product assistance at

www.whalenfurniture.com

Or e-mail your request to parts@whalenfurniture.com

LOT NUMBER:

DATE PURCHASED: / /

Model # BBHC60DBC

Please call for replacement parts or assistance: 1-866-942-5362

Whalen Furniture Mfg., Inc Factory # 7-1564 Page 2

QUALITY GUARANTEE

We are confident that you will be delighted with your Whalen Furniture purchase.

Should this product be defective in workmanship or materials or fail under normal use,

we will repair or replace it for up to one (1) year from date of purchase. Every Whalen

Furniture product is designed to meet your highest expectations. We guarantee that you

will immediately see the value of our fine furniture.

This warranty gives you specific legal rights and you may also have other rights which

vary from State to State.

Customer Service: 1-866-942-5362

8:30 a.m. - 4:30 p.m. PST, Monday to Friday

www.whalenfurniture.com

MANUFACTURER: WHALEN FURNITURE

CATALOG: 60” HIGH CONSOLE (BBHC60DBC)

DATE OF MANUFACTURE: JULY 2010

MADE IN CHINA

IMPORTANT INFORMATION

FITS UP TO MOST 65” FLAT PANEL TVs

MAXIMUM LOAD 165 lb. (74.8 kg)

MAXIMUM LOAD 50 lb. (22.7 kg)

MAXIMUM LOAD 30 lb. (13.6 kg)

THIS UNIT IS INTENDED FOR USE ONLY WITH THE PRODUCTS

AND MAXIMUM WEIGHTS INDICATED. USE WITH OTHER PRODUCTS OR PRODUCTS

HEAVIER THAN THE MAXIMUM WEIGHTS INDICATED MAY RESULT IN INSTABILITY

CAUSING POSSIBLE INJURY. THE BASE OF THE TELEVISION MUST BE PLACED

SQUARELY IN THE CENTER OF THE STAND WITH NO OVERHANGING ON EITHER SIDE.

Model # BBHC60DBC

Please call for replacement parts or assistance: 1-866-942-5362

Whalen Furniture Mfg., Inc Factory # 7-1564 Page 3

Parts and Hardware List

Please read completely through the instructions and verify that all parts listed are present before

beginning assembly.

A- Console (1)

B- Adjustable Shelf (2) C- Cable Control (2)

(Pre-attached)

(1) – 3/4” Bolt (4+1 extra) (2) – Handle w/Fastener (4)

(3) - Shelf Pin w/Hole (8) (4) - 1/2” Wood Screw (8)

(Pre-attached) (Pre-attached)

Touch-up Pen (1) Tipping Restraint Hardware Kit (2)

(Included in plastic bag)

Tools required: Phillips Head Screwdriver.

Model # BBHC60DBC

Please call for replacement parts or assistance: 1-866-942-5362

Whalen Furniture Mfg., Inc Factory # 7-1564 Page 4

DRAWER INSTALLATION

If you need to remove the drawers with ball bearing slides from the unit, please follow the

steps below to prevent any damage to the slides or the drawers.

1. If you need to remove the Drawer, please pull the drawer all the way out, then push the plastic release

lever of the ball bearing slide up on one side and down on the other side, and then pull the drawer

completely out. See detail #A.

2. To place the drawer back, simply push the ball bearing cart all the way to the end of the slides (in

both sides), and align the slides track on the drawer with the slides bearing on the unit and push it

carefully inside until it stops. See detail #B.

Note: If they do not go together smoothly, please take out and repeat step.

How to adjust the European adjustable hinges on doors

Shipping may cause doors to become out of alignment. If you find that the doors need to be

adjusted slightly, turn the appropriate screw, as illustrated.

1. TO ADJUST DOOR FORWARD OR BACKWARD.

2. TO ADJUST DOOR TO RIGHT OR TO LEFT.

3. TO ADJUST DOOR UP OR DOWN.

Model # BBHC60DBC

Please call for replacement parts or assistance: 1-866-942-5362

Whalen Furniture Mfg., Inc Factory # 7-1564 Page 5

Assembly Instructions

1. Unpack the unit and confirm that you have all the hardware and required parts listed.

2. Position the Console on your desired location against wall to place your TV on top when you finish

assembly.

3. Open the doors and drawers and install the Handle (2) to the front side with Bolt and Flat Washer

provided. Tighten the bolts with Phillips Head Screwdriver. See detail #1.

4. If you want to change the height of Adjustable Shelves (B), open the doors and unscrew the 1/2”

Wood Screws (4) pre-attached underneath the Adjustable Shelf. Replace the Adjustable Shelf at your

desired height with the Shelf Pins (3), secure the Shelf in place by screw back the 1/2” Wood Screws.

See detail #1A.

5. The vented Back Panels are removable for easy access to audio and video component hook-up. Make

sure you route the cables through the cutout on the side of back panels instead of the ventilation hole.

As shown in detail #2.

Model # BBHC60DBC

Please call for replacement parts or assistance: 1-866-942-5362

Whalen Furniture Mfg., Inc Factory # 7-1564 Page 6

Assembly Instructions

6. Attach 2 Cable Controls (C) onto the backside of Console (A) with the 3/4” Bolts (2) and tighten with

Phillips Head Screwdriver. See detail #3.

7. The Cable Controls (C) enable you to shorten, separate and route both single and bundled cables.

Using the Cable Controls you can create a system for routing cables through channels, between

components and to power sources without usual tangled mess or annoying signal interference. As

shown in detail #3.

8. In case of uneven floor, Floor Levelers are provided at the bottom of console. To adjust unit in case

of tilting or doors not being level, simply tilt the unit back and adjust floor levelers by hand to correct

tilting and/or level doors. As shown in detail #4.

Model # BBHC60DBC

Please call for replacement parts or assistance: 1-866-942-5362

Whalen Furniture Mfg., Inc Factory # 7-1564 Page 7

TIPPING RESTRAINT HARDWARE

Note: We have included two Tipping Restraint Hardware bags for this unit. You must install this hardware to

prevent accidents or injuries from falling unit.

When properly installed, this restraint can provide protection against the unexpected tipping of the unit due

to small tremors, bumps or climbing. We strongly recommend mounting this hardware to a wall stud and

your unit.

Please carefully read the instructions printed on the plastic bag.

Note: You must install the Tipping Restraint Hardware with the unit in use to prevent any accidents

or damage to the unit.

Tools required: Phillips Screwdriver, Mallet, Power Drill, and 3/8” Drill Bit.

Care and Maintenance

 Use a soft, clean cloth that will not scratch the surface when dusting.

 Use of furniture polish is not necessary. Should you choose to use polish, test in an inconspicuous area

first.

 Using solvents of any kind on your furniture may damage the finish.

 Never use water to clean your furniture as it may cause damage to the finish.

 Always use coasters under beverage glasses and flowerpots.

 Liquid spills should be removed immediately. Using a soft clean cloth, blot the spill gently. Avoid rubbing.

 Always use protective pads under hot dishes and plates. Heat can cause chemical changes that may create

spotting within the furniture finish.

 Stains or marks from crayons or ink markers will be difficult to remove.

 In the event that your furniture is stained or otherwise damaged during use, we recommend that you call a

professional to repair your furniture.

Further advice about wood furniture care

It is best to keep your furniture in a climate-controlled environment. Extreme temperature and humidity

changes can cause warping, shrinking and splitting of wood. It is advised to keep furniture away from direct

sunlight as may sun damage the finish.

Proper care and cleaning at home will extend the life of your purchase. Follow these important and helpful

tips that will enhance your furniture as it ages.

A Touch-up Pen has been provided to repair any small nicks or scratches that may occur during

assembly or shipping.

We hope you enjoy your purchase for many years.

Thanks for your purchase!

IF YOU NEED TO ORDER PARTS PLEASE USE THE LIST BELOW

60” High Console (BBHC60DBC)

*BBHC60DBC-1-AS Adjustable Shelf *BBHC60DBC-12-RBP Removable Back Panel

*BBHC60DBC-2-LD Left Door complete *BBHC60DBC-13-CC Cable Control

*BBHC60DBC-3-RD Right Door complete *BBHC60DBC-14-FL Floor Leveler

*BBHC60DBC-4-DG Door Glass only *BBHC60DBC-15-SPH Shelf Pin w/Hole

*BBHC60DBC-5-GL Glass Liner *BBHC60DBC-16- 1/2WS 1/2" Wood Screw

*BBHC60DBC-6-MC Magnetic Catches *BBHC60DBC-17-3/4B 3/4" Bolt

*BBHC60DBC-7-DHS Door Hinge w/Screw *BBHC60DBC-18-TUP Touch-up Pen

*BBHC60DBC-8-H/F Handle w/Fastener *BBHC60DBC-19-TRHK

Tipping Restraint Hardware Kit

*BBHC60DBC-9-CD Center Drawer *BBHC60DBC-20-CH Complete hardware

*BBHC60DBC-10-DS Drawer Slides *BBHC60DBC-21-RC Roller Catch

*BBHC60DBC-11-DD Drawer Divider *BBHC60DBC-22-RCMP Roller Catch Metal Plate

Whalen BBHC60DBC User manual

Whalen BBHC60DBC User manual

Related papers

Other documents