Whalen XLGTD-8 User manual

THIS INSTRUCTION BOOKLET CONTAINS IMPORTANT SAFETY INFORMATION. PLEASE

READ AND KEEP FOR FUTURE REFERENCE.

Whalen Furniture Mfg., Inc. Page 1 Factory # 11906

3-in-1 Gaming Theater

TM

Console with Storage Drawer

Model # WMCXLGTD-8

This item is designed to be a 3-in-1 configuration. Please choose the option that best suits your

needs. DO NOT discard any of the hardware or parts that you will not use on your set option. This will

give you the opportunity to use this TV Stand for different configurations in case you decide to

upgrade your TV set in the future.

ADULT ASSEMBLY REQUIRED

If you have any questions regarding assembly or if parts are missing, DO NOT return this item to the

store where it was purchased. Please call our toll-free customer service number and have your

instructions and parts list ready to provide the model name, part name or factory number:

1-866-942-5362 8:30 a.m. - 4:30 p.m., PST, Monday - Friday

ONLINE: www.whalenstyle.com EMAIL: parts@whalenfurniture.com

On-line Video Instruction Guides

Go to http://whalen.showuhow.com to view step-by-step instructional

videos for assembling and installing your product. Enter the following

product number on the ShowUhow homepage.

LOT NUMBER:

DATE PURCHASED: / /

WMCXLGTD-8

Please call for replacement parts or assistance: 1-866-942-5362

Whalen Furniture Mfg., Inc. Page 2 Factory # 11906

MANUFACTURER: Whalen Furniture

CATALOG: 3-in-1 Gaming Theater

TM

Console with Storage Drawer (WMCXLGTD-8)

DATE OF MANUFACTURE: March 2012

MADE IN CHINA

1. Please read the Assembly Instructions prior to assembling this product.

2. Remove all hardware from box and sort by size.

3. Check to see that all hardware and parts are present BEFORE assembling.

4. Ask a friend to assist you with the assembly of this furniture.

5. To avoid damage, assemble the product on a sturdy, level and protective surface.

6. Please wait until all steps are completed before tightening bolts.

7. Make sure all bolts are tightly fastened before the unit is used.

MAXIMUM RECOMMENDED WEIGHT LOADS

MAXIMUM LOAD 20 lb. (9.07 kg)

GENERAL INFORMATION, TIPS and TRICKS

This product is sold with Tip Restraint Hardware kit. You must install the Tipping Restraint

Hardware between the wall and the TV stand to prevent any accidents or damages. When

properly installed, this restraint can provide protection against the unexpected tipping of the

unit due to small tremors, bumps or climbing. The restraint is only a deterrent and is not a

substitute for proper adult supervision. Use of tip-over restraints may only reduce, but not

eliminate, the risk of tip-over.

FITS UP TO MOST 60” FLAT PANEL TVs

MAXIMUM LOAD 135 lb. (61.2 kg)

FITS UP TO MOST 60” FLAT PANEL TVs

WITHOUT SWIVELING BRACKET

MAXIMUM LOAD 135 lb. (61.2 kg)

MAXIMUM LOAD 50 lb. (22.7 kg)

THIS UNIT IS NOT INTENDED FOR USE WITH CRT TVS. USE ONLY WITH

FLAT PANEL TVS AND AUDIO/VIDEO EQUIPMENT MEETING RECOMMENDED SIZE AND

WEIGHT LIMITS. NEVER USE WITH LARGER/HEAVIER THAN RECOMMENDED FLAT

PANEL TVS OR EQUIPMENT. TO AVOID INSTABILITY, PLACE FLAT PANEL TV IN CENTRE

OF UNIT; CRT TVS, IMPROPERLY POSITIONED FLAT PANEL TVS, OR FLAT PANEL TVS OR

OTHER EQUIPMENT THAT EXCEED RECOMMENDED SIZE AND WEIGHT LIMITS COULD

FALL OFF OR BREAK THE UNIT, CAUSING POSSIBLE SERIOUS INJURY.

MAXIMUM LOAD 15 lb. (6.8 kg)

PLACE TV BEHIND THE STOPPER

Please call for replacement parts or assistance: 1-866-942-5362

Whalen Furniture Mfg., Inc. Page 3 Factory # 11906

Parts and Hardware List

Please read completely through the instructions and verify that all parts listed are present

before beginning assembly.

A- TOP SHELF FRAME (1) B- MIDDLE UPPER METAL FRAME (1) C- BOTTOM SHELF FRAME (1)

D- LONG SPINE (1) D1- SHORT SPINE (1) E- LEFT SIDE FRAME (1)

F- RIGHT SIDE FRAME (1) G- LEFT SIDE PANEL (1) H- RIGHT SIDE PANEL (1)

I- DIVIDER PANEL (1) J- LEFT LEG (1) K- RIGHT LEG (1)

L- TOP GLASS (1) M- GLASS SHELF (2) N- SWIVELING BRACKET (1)

O- XYZ MOUNTING FRAME (1) P- MONITOR BRACKET (2) Q- SSS SPINE (1)

PR

PL

Please call for replacement parts or assistance: 1-866-942-5362

Whalen Furniture Mfg., Inc. Page 4 Factory # 11906

Parts and Hardware List

Please read completely through the instructions and verify that all parts listed are present

before beginning assembly.

R- SENSOR/SOUND SHELF (1) S- LEFT DRAWER FRONT (1) T- RIGHT DRAWER FRONT (1)

U- DRAWER BACK (2) V- DRAWER LEFT SIDE (2) W- DRAWER RIGHT SIDE (2)

X- DRAWER BOTTOM Y- DRAWER BOTTOM SUPPORT Z- SPINE DECORATIVE PANEL

(2) (2) (1)

AA- ADJUSTABLE SHELF FRAME (1) BB- GAMING GUITAR CLIP (1) CC- CABLE WHEEL (2)

(1) SUCTION CUP (2) 1/2” BOLT (3) 5/8” BOLT (4) 1” BOLT

(7+1 extra) (8+1 extra) (33+1 extra) (14+1 extra)

(5) 1-5/8” BOLT (6) LOCK WASHER (7) FLAT WASHER (8) LARGE FLAT WASHER

(6+1 extra) (50+2 extra) (50+2 extra) (4+1 extra)

Please call for replacement parts or assistance: 1-866-942-5362

Whalen Furniture Mfg., Inc. Page 5 Factory # 11906

Parts and Hardware List

Please read completely through the instructions and verify that all parts listed are present

before beginning assembly.

(9) 2-1/2” LAG BOLT (10) CONCRETE ANCHOR (11) GLASS BUMPER

(4) (4) (11+1 extra)

(12) PLASTIC HOUSING (13) HANDLE w/BOLTS (14) ACRYLIC STOPPER

(8) (2) (1)

M4 ALLEN WRENCH 3/16” ALLEN WRENCH TOUCH-UP PEN TIPPING RESTRAINT HARDWARE KIT (1)

(2) (1) (1) (Inside Plastic Bag)

TV Mounting Kit

M4 x 12 BOLT (4) M4 x 30 BOLT (4) M5 x 12 BOLT (4) M5 x 30 BOLT (4)

M6 x 12 BOLT (4) M6 x 35 BOLT (4) M8 x 16 BOLT (4) M8 x 40 BOLT (4)

M4 LOCK WASHER (4) M5 LOCK WASHER (4) M6 LOCK WASHER (4) M8 LOCK WASHER (4)

LARGE SPACER (4) SMALL SPACER (4) M4/M5 FLAT WASHER (8) M6/M8 FLAT WASHER (4)

Tools required: Allen Wrench (provided) and Phillips Screwdriver (not provided).

Please call for replacement parts or assistance: 1-866-942-5362

Whalen Furniture Mfg., Inc. Page 6 Factory # 11906

Drawer Assembling

1. Unpack the unit and confirm that you have all the hardware and required parts listed.

2. Locate a DRAWER BACK (U) on a flat and protected surface with the groove facing up.

Connect one DRAWER RIGHT SIDE (W) to the DRAWER BACK (U) by inserting one PLASTIC

HOUSING (12) all the way onto the corner PLASTIC JOINTS.

NOTE: Using the end wood dowels for easy alignment. Make sure the grooves line up with each

other.

3. Repeat last step to connect one DRAWER LEFT SIDE (V) to the DRAWER BACK (U) at the

other end.

V/W

U

V/W

12

U

PLASTIC HOUSING

(2 used in this step)

⑫

Please call for replacement parts or assistance: 1-866-942-5362

Whalen Furniture Mfg., Inc. Page 7 Factory # 11906

Drawer Assembling

4. Align and attach the DRAWER BOTTOM SUPPORT (Y) to the DRAWER BACK (U) by

engaging the PLASTIC FITTING.

NOTE: Turn the Lever if necessary when aligning the PLASTIC FITTING. Once the latch of

PLASTIC FITTING is connected inside Socket, push the Lever all the way to the side with

cutout to connect them together.

5. Slide the DRAWER BOTTOM (X) into the grooves in the DRAWER SIDES and DRAWER

BACK. Ensure the unfinished surface of DRAWER BOTTOM will face floor.

Y

U

Please call for replacement parts or assistance: 1-866-942-5362

Whalen Furniture Mfg., Inc. Page 8 Factory # 11906

Drawer Assembling

6. Align and attach one DRAWER FRONT (S or T) to the other end of DRAWER BOTTOM

SUPPORT (Y) by engaging the PLASTIC FITTING. Make sure that DRAWER BOTTOM (X) fits

securely into the groove of the DRAWER FRONT as shown above.

Y

S/T

Please call for replacement parts or assistance: 1-866-942-5362

Whalen Furniture Mfg., Inc. Page 9 Factory # 11906

Drawer Assembling

7. Align and insert two PLASTIC HOUSINGS (12) all the way onto the corner PLASTIC JOINTS to

secure the DRAWER FRONT in place.

8. Remove the bolts in one HANDLE (13), then use the bolts to attach the HANDLE to the outside

of DRAWER FRONT (S or T).

9. Repeat the process to assemble the other drawer.

HANDLE AND BOLTS

(1 used in this step)

⑬

S/T

U/V

12

S/T

13

PLASTIC HOUSING

(2 used in this step)

⑫

Please call for replacement parts or assistance: 1-866-942-5362

Whalen Furniture Mfg., Inc. Page 10 Factory # 11906

Assembly Instructions

NOTE: Please do not fully tighten all bolts until you finish assembling all parts. Once assembled,

go back and fully tighten all bolts. This will make it easier during assembly of unit.

10. Choose the option suits your needs. Locate LONG SPINE (D) or SHORT SPINE (D1) and set

back face down on a scratch-free surface as shown above.

11. Fasten TOP SHELF FRAME (A) to the SPINE using two 5/8” BOLTS (3) with LOCK WASHERS

(6) and FLAT WASHERS (7). Make sure that the flush surfaces of TOP SHELF FRAME will

face up after assembly.

12. Fasten the MIDDLE UPPER METAL FRAME (B), ADJUSTABLE SHELF FRAME (AA) and

BOTTOM SHELF FRAME (C) to the SPINE using six 1” BOLTS (4). Make sure the metal tabs

on shelf frames point upward and the flush surfaces of ADJUSTABLE SHELF FRAME (AA) will

face down after assembly. NOTE: Choose the upper hole sets for the ADJUSTABLE SHELF

FRAME (AA) to increase the bottom space.

LOCK WASHER

(2 used in this step)

⑥

FLAT WASHER

(2 used in this step)

⑦

1” BOLT

(6 used in this step)

④

5/8” BOLT

(2 used in this step)

③

Please call for replacement parts or assistance: 1-866-942-5362

Whalen Furniture Mfg., Inc. Page 11 Factory # 11906

Assembly Instructions

13. Fasten DIVIDER PANEL (I) to the middle rail of TOP SHELF FRAME (A) and MIDDLE UPPER

METAL FRAME (B) using four 5/8” BOLTS (3) and WASHERS (6 and 7).

NOTE: Make sure the drawer slides locate at bottom portion and slide opening face front of unit.

LOCK WASHER

(4 used in this step)

⑥

FLAT WASHER

(4 used in this step)

⑦

5/8” BOLT

(4 used in this step)

③

Please call for replacement parts or assistance: 1-866-942-5362

Whalen Furniture Mfg., Inc. Page 12 Factory # 11906

Assembly Instructions

14. Fasten the LEFT SIDE PANEL (G) to the LEFT SIDE FRAME (E) using four 1” BOLTS (4) and

WASHERS (6 and 7).

NOTE: Make sure that the slide track on SIDE PANEL faces inward and the slide opening

points toward the front end of SIDE FRAME (with metal brackets).

15. Repeat last step to fasten the RIGHT SIDE PANEL (H) to the RIGHT SIDE FRAME (F).

LOCK WASHER

(8 used in this step)

⑥

FLAT WASHER

(8 used in this step)

⑦

1” BOLT

(8 used in this step)

④

Please call for replacement parts or assistance: 1-866-942-5362

Whalen Furniture Mfg., Inc. Page 13 Factory # 11906

Assembly Instructions

16. Stand last assemblies upright.

17. Fasten the LEFT SIDE FRAME (E) to the back rail of SHELF FRAMES (A, B, AA and C). Use

four 5/8” BOLTS (3) and WASHERS (6 and 7).

18. Repeat last step for the RIGHT SIDE FRAME (F).

LOCK WASHER

(8 used in this step)

⑥

FLAT WASHER

(8 used in this step)

⑦

D1

D

E/F

A

3

7

6

5/8” BOLT

(8 used in this step)

③

Please call for replacement parts or assistance: 1-866-942-5362

Whalen Furniture Mfg., Inc. Page 14 Factory # 11906

Assembly Instructions

19. Fit and attach LEFT LEG (J) and RIGHT LEG (K) to the front of SIDE FRAMES (E and F) and

ADJUSTABLE SHELF FRAME (AA) using eight 5/8” BOLTS (3) with WASHERS (6 and 7)

through the inner hole of metal brackets.

NOTE: Make sure top surfaces are even with each other and there are no gaps between

LEGS (J and K) and SIDE PANELS (G and H).

20. Fasten LEGS (J and K) to the front rail of SHELF FRAMES (A, B and C). Use six 1-5/8”

BOLTS (5) and WASHERS (6 and 7) through the outer hole of metal brackets on SIDE

FRAMES (E and F).

F

3

7

6

5

7

6

J/K

E/F

A/B/C

J/K

LOCK WASHER

(14 used in this step)

⑥

FLAT WASHER

(14 used in this step)

⑦

1-5/8” BOLT

(6 used in this step)

⑤

5/8” BOLT

(8 used in this step)

③

Please call for replacement parts or assistance: 1-866-942-5362

Whalen Furniture Mfg., Inc. Page 15 Factory # 11906

Assembly Instructions

21. Go back and tighten all bolts with enclosed M4 ALLEN WRENCH.

22. Adjust the FLOOR LEVELERS pre-attached at the bottom of LEGS (J and K) to level the unit.

If you choose Table-top configuration,

continue to next step.

If mounting TV with the Floating Swivel

Mount, skip ahead to PAGE 21.

Please call for replacement parts or assistance: 1-866-942-5362

Whalen Furniture Mfg., Inc. Page 16 Factory # 11906

Assembly Instructions for Table-top

23. Attach GAMING GUITAR CLIP (BB) and CABLE WHEELS (CC) onto the backside of SHORT

SPINE (D1) using five 5/8” BOLTS (3).

NOTE: You can use the CABLE WHEELS to help keep your entertainment center’s cables

and cords organized. The GAMING GUITAR CLIP (BB) can provide storage of gaming guitar

controllers.

BB

3

CC

3

D1

5/8” BOLT

(5 used in this step)

③

Please call for replacement parts or assistance: 1-866-942-5362

Whalen Furniture Mfg., Inc. Page 17 Factory # 11906

Assembly Instructions for Table-top

24. To insert the assembled drawers into your unit, extend the SLIDE TRACKS on the SIDE

PANELS (G and H) and DIVIDER PANEL (I) all the way forward (including ball bearing cart).

Then align the SLIDE RUNNERS on the assembled drawers with the SLIDING TRACKS and

push the drawer carefully inside until it stops.

NOTE: If they do not go smoothly, please take out and repeat the step. If you need to remove

the drawer, please pull the drawer all the way out, then simultaneously push the PLASTIC

RELEASE LEVER of the ball bearing slides up on one side and down on the other side, and

then pull it completely out.

V/W

G/H/I

I

Please call for replacement parts or assistance: 1-866-942-5362

Whalen Furniture Mfg., Inc. Page 18 Factory # 11906

Assembly Instructions for Table-top

25. Put SUCTION CUPS (1) firmly into the top holes of TOP SHELF FRAME (A) and evenly place

the GLASS BUMPERS (11) on the ADJUSTABLE SHELF FRAME (AA) and BOTTOM SHELF

FRAME (C) as shown above.

Tip: If a SUCTION CUP resists insertion, try pressing down on the middle of the cup with the

Allen Wrench while twisting it clockwise into the hole.

26. Place GLASS SHELVES (L and M) with the black side of glass down onto the SUCTION

CUPS (1) and GLASS BUMPER (11). Push each glass all the way back against the SPINE.

NOTE: If glass is scratched you can minimize the damage by using a BLACK marker and filling

in scratched area from underneath.

SUCTION CUP

(7 used in this step)

①

GLASS BUMPER

(11 used in this step)

⑪

1

C/AA

11

C

AA

Please call for replacement parts or assistance: 1-866-942-5362

Whalen Furniture Mfg., Inc. Page 19 Factory # 11906

Assembly Instructions

NOTE: You must install the Acrylic TV Stopper to prevent TV from tipping when placing your flat

panel television directly on the table-top console.

27. Remove the tape of ACRYLIC STOPPER (14) and place it on the cut-out of the warning label

on the front of TOP GLASS (L). Make sure it is aligned before applying pressure.

28. Remove the warning label for ACRYLIC STOPPER carefully.

ACRYLIC STOPPER

(1 used in this step)

⑭

L

Please call for replacement parts or assistance: 1-866-942-5362

Whalen Furniture Mfg., Inc. Page 20 Factory # 11906

Assembly Instructions for Table-top

Tools required: Allen Wrench (provided), Phillips Screwdriver, Mallet, Power Drill, and 3/8” Drill Bit.

29. Position the assembled Table-top in your desired location against a wall. Now follow the

instructions printed on the plastic bag containing the TIPPING RESTRAINT HARDWARE to

mount the tipping restraint to the SPINE and the wall.

NOTE: YOU MUST USE THIS TIPPING RESTRAINT TO ATTACH THIS UNIT TO THE

WALL, TO PREVENT ACCIDENTS AND/OR INJURIES.

30. The Table-top is ready for use now. Be sure to position your Flat Panel TV in center of the

console.

NOTE: For Tilting Wall Mount, proceed to PAGE #30.

Page is loading ...

Whalen XLGTD-8 User manual

Whalen XLGTD-8 User manual

Related papers