Vista Architectural Series Installation Instructions Manual
- Type
- Installation Instructions Manual
Vista Architectural Series LED Retrofit Kit is designed to provide energy-efficient lighting solutions for existing HID and fluorescent fixtures, offering easy installation and compatibility with various luminaires. It features a sleek design and integrates seamlessly into existing housings, making it an ideal choice for upgrading lighting systems in both indoor and outdoor applications.
Vista Architectural Series LED Retrofit Kit is designed to provide energy-efficient lighting solutions for existing HID and fluorescent fixtures, offering easy installation and compatibility with various luminaires. It features a sleek design and integrates seamlessly into existing housings, making it an ideal choice for upgrading lighting systems in both indoor and outdoor applications.
INSTALLATION INSTRUCTIONS
LED Retrofit Kit
Architectural Series
RK94
1625 Surveyor Avenue • Simi Valley, CA 93063 • (805) 527-0987 • (800) 766-VISTA (8478)
FAX: (888) 670-VISTA (8478) • [email protected] • www.vistapro.com
Vista Professional Outdoor Lighting reserves the right to modify the design and/or construction of the fixture shown without further notification.
1/6
WARNING – RISK OF FIRE OR ELECTRIC SHOCK. INSTALL THIS KIT ONLY IN THE LUMINAIRES
THAT HAS THE CONSTRUCTION FEATURES AND DIMENSIONS SHOWN IN THE PHOTOGRAPHS
AND/OR DRAWINGS AND WHERE THE INPUT RATING OF THE RETROFIT KIT DOES NOT EXCEED
THE INPUT RATING OF THE LUMINAIRE.
AVERTISSEMENT – RISQUE D’INCENDIE OU DE CHOC ÉLECTRIQUE. N’INSTALLER CE NÉCESSAIRE
QUE DANS LES LUMINAIRES DONT LES CARACTÉRISTIQUES DE CONSTRUCTION ET LES
DIMENSIONS SONT CONFORME À CELLES ILLUSTRÉES DANS LES PHOTOS ET/OU LES DESSINS
ET DONT LA PUISSANCE D’ENTRÉE NOMINALE DU NÉCESSAIRE DE MODERNISATION NE
DÉPASSE PAS CELLE DU LUMINAIRE.
___________________________________________________________________________________________
THIS RETROFIT KIT IS ACCEPTED AS A COMPONENT OF A LUMINAIRE WHERE THE SUITABILITY
OF THE COMBINATION SHALL BE DETERMINED BY AUTHORITIES HAVING JURISDICTION. (S24-L5)
LE NÉCESSAIRE DE MODERNISATION EST ACCEPTÉ À TITRE DE COMPOSANT D’UN LUMINAIRE
LORSQUE LA PERTINENCE DE LA COMBINAISON DOIT ËTRE DÉTERMINÉE PAR PAR LES
AUTORITÉS COMPÉTENTES
___________________________________________________________________________________________
DO NOT MAKE OR ALTER ANY OPEN HOLES IN AN ENCLOSURE OF WIRING OR ELECTRICAL
COMPONENTS DURING KIT INSTALLATION.
IL EST INTERDIT DE FAIRE OU DE MODIFIER UNE OUVERTURE DANS UN BOÎTIER DE CÂBLAGE OU
DE COMPOSANTS ÉLECTRIQUES AU COURS DE L’INSTALLATION DU NÉCESSAIRE. (S24-L5)
___________________________________________________________________________________________
WARNING – RISK OF FIRE OR ELECTRIC SHOCK. INSTALLATION OF THIS RETROFIT ASSEMBLY
REQUIRES A PERSON FAMILIAR WITH THE CONSTRUCTION AND OPERATION OF THE
LUMINAIRE’S ELECTRICAL SYSTEM AND THE HAZARD INVOLVED. IF NOT QUALIFIED, DO NOT
ATTEMPT INSTALLATION. CONTACT A QUALIFIED PERSON.
AVERTISSEMENT – RISQUE D’INCENDIE OU DE CHOC ÉLECTRIQUE. L’INSTALLATION DE CE
NÉCESSAIRE DE MODERNISATION EXIGE UNE PERSONNE FAMILIÈRE AVEC LA CONSTRUCTION
ET LE FONCTIONNEMENT DU SYSTÈME ÉLECTRIQUE DU LUMINAIRE ET DES RISQUES ASSOCIÉS.
TOUTE PERSONNE QUI N’EST PAS QUALIFIÉE NE DOIT FAIRE AUCUNE TENTATIVE
D’INSTALLATION ET DOIT CONTACTER UNE PERSONNE QUALIFIÉE.
INSTALLATION INSTRUCTIONS
LED Retrofit Kit
Architectural Series
RK94
1625 Surveyor Avenue • Simi Valley, CA 93063 • (805) 527-0987 • (800) 766-VISTA (8478)
FAX: (888) 670-VISTA (8478) • [email protected] • www.vistapro.com
Vista Professional Outdoor Lighting reserves the right to modify the design and/or construction of the fixture shown without further notification.
IMPORTANT NOTE:
• Retrofit Kit must be installed and grounded in accordance with the National Electrical Code (NEC) and local codes.
• All conduit entries must be sealed from moisture. Use appropriate sealing material on conduit fittings and conduit closure plugs.
• Retrofit Kit is wet location listed and suitable for mounting in Hydrel® Model M9400 Series in-grade rough-in sections.
• Suitable for all types of construction including poured concrete construction and in soil applications.
• Suitable for through wiring: Max. of (4) No. 12 AWG conductors (plus ground) rated for 90°C.
MAINTENANCE: To assure proper operation and efficiency and to prevent luminaire overheating, lens must be kept clean and free of dirt, dust, leaves, trash and mineral
deposits from water. A regular schedule maintenance program is recommended.
NOTE: Save these instructions for future reference.
NOTICE: To prevent electric shock, turn main power off at circuit breaker. DO NOT INSTALL RETROFIT WHILE SYSTEM IS ENERGIZED.
Disassembly of Existing Fixture-HID/Fluorescent Version:
1. Remove and discard existing door assembly.
2. Remove and discard existing Lamp Module and any associated bracketry and hardware by lifting the Lamp Module out of the Housing and unplugging
it from the Power Module.
3. Loosen Support Ring screws and remove Support Ring from the Housing. Retain Support Ring and screws as these will be reused later. Inspect
components for damage and replace any damaged parts prior to installation of the Reftrofit Kit.
4. Remove Power Module from Housing and set on grade outside of fixture.
5. Remove J-Box Cover and disconnect the wiring splices within the J-Box. Discard the old Wire-Nuts.
6. Pull J-Box Cover from within the Housing and remove the Cord Seal from the J-Box Cover. Discard the Power Module along with the old Cord Seal.
Retain J-Box Cover with gasket and screws as these will be reused later. Inspect components for damage and replace any damaged parts prior
to installation of the Reftrofit Kit.
DOOR ASSEMBLY
(may include glass)
r
emove and discard
OLD CORD SEAL
& OLD WIRE-NUTS
remove and discard
LAMP MODULE
(and associated bracketry)
remove and discard
POWER MODULE
remove and discard
J-BOX COVER
remove and retain
SUPPORT RING
remove and retain
HID/FLUORESCENT
HOUSING
fixed and buried
Disassembly of Existing Fixture HID/Fluorescent Version
2/6
1625 Surveyor Avenue • Simi Valley, CA 93063 • (805) 527-0987 • (800) 766-VISTA (8478)
FAX: (888) 670-VISTA (8478) • [email protected] • www.vistapro.com
Vista Professional Outdoor Lighting reserves the right to modify the design and/or construction of the fixture shown without further notification.
ASSEMBLY OF RETROFIT KIT WITHIN FIXTURE- HID and Fluorescent:
1. Firmly tighten newly provided Cord Seal into J-Box Cover ensuring a liquid tight fitting.
NOTE: If a Stainless Trim Ring (STR) accessory is to be used, route the free end (Load) of Retrofit LED Module Cable through the top side of the STR
before continuing to step 2.
2. Route the free end (Load) of Retrofit LED Module Cable (A) through the top side of the support Ring and (B) through the new Cord Seal such that the
Cable Jacket extends past the Cord Seal 1”-2” and that the splices will terminate within the J-Box. Firmly tighten the nut on the Cord Seal ensuring a
liquid tight fitting.
3. Using the provided Silicone Filled Wire-Nuts, connect the supply conductors within the J-Box to the load conductors of the Retrofit LED Module.
NOTE: See sheet 6 for wiring diagrams of both (A) Standard 3 Wire Electrical Connections and (B) Optional 5 Wire 0-10V Dimming Electrical Connections.
4. Re-install junction box cover and gasket making sure that none of the splices are pinched within the seal. Tighten to ensure proper sealing.
5. Set the Support Ring within the Housing and secure with the screws in the desired position. The Module Logo will be centered between the door
screw locations.
NOTE: If a Stainless Trim Ring (STR) accessory is to be used, set the STR inside the top lip of the housing before continuing to step 6.
6. Place the LED Retrofit module within the Support Ring by aligning the two (2) captive screws of the Module with the mating fasteners of Support Ring.
Snug the captive screws to secure the Module (do not overtighten).
7. Supply power to the luminaire and check for proper operation.
Assembly of Retrofit Kit within the HID/Fluorescent Hydrel® Housing
New Cord Seal
J-Box
Retrofit LED Module
Exploded Assembly
Captive Door Screws
(180° apart)
Module Logo
(centered between
Door Screw Locations)
Door Screw location
(180° apart)
Cable Jacket extends
past Cord Seal 1”- 2”
New Silicone Filled Wire-Nuts
-3 EA for Non Dimming & Triac Dimming
-5 EA for 0-10V Dimming
(connects Supply Conductors to Retrofit LED
Module Cable conductors (Load)
Supply Conductors
(within J-Box)
J-Box Cover
(sectioned for clarity)
Retrofit LED Module Cable (Load)
-3 Conductor for Non Dimming & Triac Dimming
-5 Conductor for 0-10V Dimming
Support Ring
(screw to Housing
in desired position)
Route Retrofit LED Module Cable
through top side of Support Ring
Stainless Trim Ring (STR)
(optional Accessory)
Route Retrofit LED Module Cable
through top side of Stainless Trim Ring (STR)
(if STR accessory is specified)
HID/Fluorescent
Housing
(fixed and buried)
Completed Assembly
3/6
RK94 Retrofit Kit consists of:
one (1) Retrofit LED Module, one (1) Cord Seal and five (5) Silicone Filled Wire-Nuts.
Hydrel® is a registered Trade Mark of Acuity Brands.
INSTALLATION INSTRUCTIONS
LED Retrofit Kit
Architectural Series
RK94
1625 Surveyor Avenue • Simi Valley, CA 93063 • (805) 527-0987 • (800) 766-VISTA (8478)
FAX: (888) 670-VISTA (8478) • [email protected] • www.vistapro.com
Vista Professional Outdoor Lighting reserves the right to modify the design and/or construction of the fixture shown without further notification.
IMPORTANT NOTE:
• Retrofit Kit must be installed and grounded in accordance with the National Electrical Code (NEC) and local codes.
• All conduit entries must be sealed from moisture. Use appropriate sealing material on conduit fittings and conduit closure plugs.
• Retrofit Kit is wet location listed and suitable for mounting in Hydrel® Model M9400 Series in-grade rough-in sections.
• Suitable for all types of construction including poured concrete construction and in soil applications.
• Suitable for through wiring: Max. of (4) No. 12 AWG conductors (plus ground) rated for 90°C.
MAINTENANCE: To assure proper operation and efficiency and to prevent luminaire overheating, lens must be kept clean and free of dirt, dust, leaves, trash and mineral
deposits from water. A regular schedule maintenance program is recommended.
NOTE: Save these instructions for future reference.
NOTICE: To prevent electric shock, turn main power off at circuit breaker. DO NOT INSTALL RETROFIT WHILE SYSTEM IS ENERGIZED.
Disassembly of Existing Fixture-Incandescent Version:
1. Remove and discard existing door assembly.
2. Remove and discard existing Lamp Module and any associated bracketry and hardware by lifting the Lamp Module out of the Housing and unplugging
it from the Power Module.
3. Loosen Support Ring screws and remove Support Ring from the Housing. Retain Support Ring and screws as these will be reused later. Inspect
components for damage and replace any damaged parts prior to installation of the Reftrofit Kit.
4. Remove J-Box Cover and disconnect the wiring splices within the J-Box. Discard the old Wire-Nuts.
5. Pull J-Box Cover from within the Housing and remove the Cord Seal from the J-Box Cover. Discard the Power Cord along with the old Cord Seal.
Retain J-Box Cover with gasket and screws as these will be reused later. Inspect components for damage and replace any damaged parts prior
to installation of the Reftrofit Kit.
DOOR ASSEMBLY
(may include glass)
remove and discard
OLD CORD SEAL
& OLD WIRE-NUTS
remove and discard
LAMPING MODULE
(and associated bracketry)
remove and discard
POWER CORD
remove and discard
J-BOX COVER
remove and retain
SUPPORT RING
remove and retain
INCANDESCENT HOUSING
xed and buried
Disassembly of Existing Fixture Incandescent Version
4/6
1625 Surveyor Avenue • Simi Valley, CA 93063 • (805) 527-0987 • (800) 766-VISTA (8478)
FAX: (888) 670-VISTA (8478) • [email protected] • www.vistapro.com
Vista Professional Outdoor Lighting reserves the right to modify the design and/or construction of the fixture shown without further notification.
ASSEMBLY OF RETROFIT KIT WITHIN FIXTURE:
1. Firmly tighten newly provided Cord Seal into J-Box Cover ensuring a liquid tight fitting.
NOTE: If a Stainless Trim Ring (STR) accessory is to be used, route the free end (Load) of Retrofit LED Module Cable through the top side of the STR
before continuing to step 2.
2. Route the free end (Load) of Retrofit LED Module Cable (A) through the top side of the support Ring and (B) through the new Cord Seal such that the
Cable Jacket extends past the Cord Seal 1”-2” and that the splices will terminate within the J-Box. Firmly tighten the nut on the Cord Seal ensuring a
liquid tight fitting.
3. Using the provided Silicone Filled Wire-Nuts, connect the supply conductors within the J-Box to the load conductors of the Retrofit LED Module.
NOTE: See sheet 6 for wiring diagrams of both (A) Standard 3 Wire Electrical Connections and (B) Optional 5 Wire 0-10V Dimming Electrical Connections.
4. Re-install junction box cover and gasket making sure that none of the splices are pinched within the seal. Tighten to ensure proper sealing.
5. Set the Support Ring within the Housing and secure with the screws in the desired position. The Module Logo will be centered between the door
screw locations.
NOTE: If a Stainless Trim Ring (STR) accessory is to be used, set the STR inside the top lip of the housing before continuing to step 6.
6. Place the LED Retrofit module within the Support Ring by aligning the two (2) captive screws of the Module with the mating fasteners of Support Ring.
Snug the captive screws to secure the Module (do not overtighten).
7. Supply power to the luminaire and check for proper operation.
Assembly of Retrot Kit within the Incandescent Housing
J-BOX Cover
(sectioned for clarity)
New Cord Seal
Route Retrot LED Module Cable
through top side of Support Ring
Support Ring
(screw to Housing
in desired position)
Supply Conductors
(within J-Box)
J-Box
Cable Jacket extends
past Cord Seal 1"-2"
Retrot LED Module Cable (Load)
-3 Conductor for Non Dimming & Triac Dimming
-5 Conductor for 0-10V Dimming
Retrot LED Module
Incandescent Housing
(xed and buried)
Door Screw location
(180
°
apart)
Module Logo
(centered between
Door Screw locations)
Captive Door Screws
(180
°
apart)
New Silicone Filled Wire-Nuts
-3EA for Non Dimming & Triac Dimming
-5EA for 0-10V Dimming
(connect Supply Conductors to Retrot LED
Module Cable conductors (Load)
Exploded Assembly
Completed Assembly
Route Retrot LED Module Cable
through top side of Stainless Trim Ring (STR)
(if STR accessory is specied)
Stainless Trim Ring (STR)
(optional Accessory)
5/6
RK94 Retrofit Kit consists of:
one (1) Retrofit LED Module, one (1) Cord Seal and five (5) Silicone Filled Wire-Nuts.
Hydrel® is a registered Trade Mark of Acuity Brands.
Vista Professional Outdoor Lighting reserves the right to modify the design and/or construction of the fixture shown without further notification.
1625 Surveyor Avenue • Simi Valley, CA 93063 • (805) 527-0987 • (800) 766-VISTA (8478)
FAX: (888) 670-VISTA (8478) • [email protected] • www.vistapro.com
6/6
RK94 12.16
WIRING DIAGRAMS:
LOAD (BLACK)
LOAD (GREEN)
LOAD (WHITE)
Retrofit LED Module Cable (LOAD)
SPLICE
(within J-Box)
(A) STANDARD 3 WIRE ELECTRICAL CONNECTIONS
SUPPLY CONDUCTORS
(120-277V LINE VOLTAGE)
120-277V SUPPLY (LINE)
SUPPLY (NEUTRAL)
SUPPLY (GROUND)
LOAD (BLACK)
LOAD (GREEN)
LOAD (WHITE)
Retrofit LED Module Cable (LOAD)
SPLICE
(within J-Box)
(B) OPTIONAL 5 WIRE 0-10V DIMMING ELECTRICAL CONNECTIONS
DIMMING LOAD (ORANGE)
DIMMING LOAD (RED)
SUPPLY CONDUCTORS
(120-277V LINE VOLTAGE)
120-277V SUPPLY (LINE)
SUPPLY (NEUTRAL)
SUPPLY (GROUND)
DIMMING CONDUCTORS
(0-10V LOW VOLTAGE)
DIMMING
(+)
DIMMING
(-)
-
1
-
2
-
3
-
4
-
5
-
6
Vista Architectural Series Installation Instructions Manual
- Type
- Installation Instructions Manual
Vista Architectural Series LED Retrofit Kit is designed to provide energy-efficient lighting solutions for existing HID and fluorescent fixtures, offering easy installation and compatibility with various luminaires. It features a sleek design and integrates seamlessly into existing housings, making it an ideal choice for upgrading lighting systems in both indoor and outdoor applications.
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI
in other languages
- français: Vista Architectural Series
Related papers
-
Vista Architectural Series Installation guide
-
Vista 12V Series Installation guide
-
-
-
-
-
-
Vista 1051 User manual
-
-
Other documents
-
kadision 60W LED Wall Pack Light Installation guide
-
Hydrel RF7 Retrofit Installation guide
-
Hinkley 51000BZ User manual
-
Acuity Brands Lighting Lithonia Lighting TWP-LED Series Installation guide
-
Light Efficient Design LED-8027M Instruction & Installation Manual
-
KUZCO ER9420 Installation guide
-
EMS FireCell Verification Manual
-
CREE LIGHTING LR4 Series Installation guide
-
Lithonia Lighting RTLR LED Installation guide
-
