Marco MIX 1 Button Font Installation guide

Marco
Brand
Marco
Model
MIX 1 Button Font
Type
Installation guide

This manual is also suitable for

1
Instruction Manual
Machine P/N: 1000878# , 1000879# & 1000879FB
2
100mm
/ 4”
32mm
/ 1 ¼”
82.5mm
Scale 1:1
For drip tray only
100mm
NOTE: Check scale of template before cutting. Scale should be 1:1
Contents
1. Font Box Contents................................................................................................2
2. Counter Cut-Out.................................................................................................2
3. Installation..........................................................................................................4
No Drip Tray...............................................................................................4
Drip Tray...................................................................................................5
Connecting Hoses......................................................................................6
4. Operating Font...................................................................................................7
5. Cleaning & Maintenance......................................................................................7
Font Box Contents
3 & 4 Button Models
• MIX Font
• Vent Hosing
• Hot Water Hose
• Cold Water Hose
• Instruction Manual
•Button Identifier Tag
•Button Identifier Clip
Counter Cut Out
• The 105mm /4 ⅛” cut out is only required for the font with drip tray.
• The font without drip tray require the 32mm / 1 ¼” cut out only.
• Use a 32mm/ 1 ¼” & a 105mm /4 ⅛” circular hole saw piece to make the holes.
Single Button Model
• MIX Font
• Vent Hosing
• Hot Water Hose
• Instruction Manual
• SP9 Adaptor Kit
3
100mm
/ 4”
32mm
/ 1 ¼”
82.5mm
Scale 1:1
For drip tray only
100mm
NOTE: Check scale of template before cutting. Scale should be 1:1
Counter Cut Out
4
Installation
32mm / 1 ¼”
1. No Drip Tray
130 - 500mm
130 - 500mm
50mm
Hosing should be trimmed to ensure
continuous drop from font to boiler
5
Installation
The drain outlet on the drip
tray should be plumbed to
waste.
32mm/ 1 ¼”
100mm/ 4”
2. Drip Tray (sold seperately p/n. 2300268)
130 - 500mm
130 - 500mm
50mm
Hosing should be trimmed to ensure
continuous drop from font to boiler
6
Hot Water
Vent
Power
Cold Water
Hot Water
Vent
Power
Connecting Hoses
Vent
Hot Water
SP9 Boiler
3 & 4 Button Font Connections Single Button Font Connections
SP9 Boiler Connection
7
Operating Font
Cleaning & Maintenance
RISK OF SCALDING
Turn off the boiler before cleaning to
prevent accidental triggering of a
dispense.
Beware of accidentally operating the font –
especially when cleaning around the push
buttons.
The exterior of this font may be cleaned
with a damp cloth and a light detergent.
Do not use abrasive cloths or creams, as
this will spoil the finish of the font.
1. Push & Hold
2. Push & Release
Quantity
85°
100
Marco Beverage Systems Limited.
63d Heather Road,
Sandyford Industrial Estate,
Dublin 18
t: +353 (0)1 295 2674
f: +353 (0)1 295 3715
e: sales@marco.ie
www.marcobeveragesystems.com
NSF/ANSI 4
E337347
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8

Marco MIX 1 Button Font Installation guide

Marco
Brand
Marco
Model
MIX 1 Button Font
Type
Installation guide
This manual is also suitable for
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents