multicomp pro TS-200S R Operating instructions
- Type
- Operating instructions
Page <2> V1.014/06/22
Newark.com/multicomp-pro
Farnell.com/multicomp-pro
sg.element14.com/b/multicomp-pro
Important Notice : This data sheet and its contents (the “Information”) belong to the members of the AVNET group of companies (the “Group”) or are licensed to it. No licence is granted for
the use of it other than for information purposes in connection with the products to which it relates. No licence of any intellectual property rights is granted. The Information is subject to change
without notice and replaces all data sheets previously supplied. The Information supplied is believed to be accurate but the Group assumes no responsibility for its accuracy or completeness,
any error in or omission from it or for any use made of it. Users of this data sheet should check for themselves the Information and the suitability of the products for their purpose and not make
any assumptions based on information included or omitted. Liability for loss or damage resulting from any reliance on the Information or use of it (including liability resulting from negligence or
where the Group was aware of the possibility of such loss or damage arising) is excluded. This will not operate to limit or restrict the Group’s liability for death or personal injury resulting from its
negligence. Multicomp Pro is the registered trademark of Premier Farnell Limited 2019.
It is called “Mechanical or Capillary thermostat” which maintains the desired temperature for the various heating or cooling
appliances. It consists of a sensing bulb to detect temperature and a switch to cut in and cut o the electric power. Be sure to
mind this manual for the most suitable application and for your safety.
Features
Temperature range to be controlled covers from - 30°C to 320°C.
The electric rating (30A/250V AC, 20A/250V AC is shown on each label of the part.
Max. ambient temperature of the thermostat body is 120°C
Not over 120% from high end temperature is allowed on the bulb temperature.
(Not over 1 05% is recommanded for thermostat higher than 300°C for safety)
Caution & Notice
1. Please mind this instructions before installing a thermostat to your equipment and contact the supplier for any question or
doubt.
2. Use it in allowed electric rating for your safety.
3. Carefulness is requ ired to handle bulb and capillary to prevent breaking.
4. Do not bend the capillary less than 5mm radius
5. A damaged bulb can make fail the desired temperature.
6. Thermostat body should be installed away from heating source. The higher ambient temperature can aect its normal function.
7. Sensing bulb should be installed in or close to heating source. Otherwise it can be out of the allowed tolerance.
8. Install the thermostat so that no pressure is applied to the body of the thermostat. Excessive pressure on the body may
cause malfunction.
9. Terminals deformation is not allowed for safety.
10. Refund or replacement is not accepted for voluntary xing or modifying.
11. Applying the supplied parts with the thermostat.
Diagram
Installation
-
1
-
2
multicomp pro TS-200S R Operating instructions
- Type
- Operating instructions
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI
Related papers
-
multicomp pro U3-SS107. User manual
-
multicomp pro MP011354 Operating instructions
-
multicomp pro U3 10HUB User manual
-
multicomp pro MP740867 UK User manual
-
multicomp pro MC29504 Operating instructions
-
multicomp pro MP005744 Operating instructions
-
multicomp pro FLDNYDX5-250 Operating instructions
-
multicomp pro MP780833 Operating instructions
-
multicomp pro MP780834 Operating instructions
-
multicomp pro MP780429 Operating instructions
Other documents
-
Tenma 72-13455 Operating instructions
-
Analog Devices EVAL-ADF4151EB1Z User manual
-
-
NXP MC33937 User guide
-
-
-
-
-
-
