Insignia NS-MVMU5 User manual

Insignia
Brand
Insignia
Model
NS-MVMU5
Type
User manual

This manual is also suitable for

Universal
Vehicle Mount
NS-MVMU5/ NS-MVMU5-C
Before using your new product, please read these instructions to prevent any damage.
USER GUIDE
2
www.insigniaproducts.com
UNIVERSAL VEHICLE MOUNT
IMPORTANT SAFETY INSTRUCTIONS
Choking Hazard
WARNING! This product may contain small parts which may be a choking hazard to
children under 3. Keep small parts away from children.
Road Hazard
WARNING! Risk of severe injury or death. This product requires in-car installation. Do not
attempt to install or set up this equipment while your vehicle is moving.
WARNING! Risk of severe injury or death. Do not install this equipment in a way that it will
obstruct the view of the driver. Some jurisdictions have restrictions regarding the installation
of after-market accessories. Consult and obey the local laws and regulations.
Notices
• The vent mount attaches to the horizontal vent louvers found in most vehicles.
Note: Does not work with circular/round type vents found in some vehicles. Removing the vent
mount can be di cult. It is designed to be attached to your car’s vents only once, and will not
transfer easily from car to car.
• Check the state and local laws and ordinances where you drive. Some state laws prohibit
drivers from using mounts on their windshields while operating motor vehicles. Other
state laws allow the mount to be located only in speci c locations on the windshield. It is
the user’s responsibility to mount the device in compliance with all applicable laws and
ordinances.
• Do not install this or any product over an air bag cover or within the air bag deployment
zone. Insignia assumes no responsibility of liability for injury or death as a result of car
crashes and/or air bag deployment.
• Insignia is not responsible for any damages caused to your car, your device, or yourself
due to the installation or use of the mounts.
• Insignia does not assume any responsibility for any  nes, penalties, or damages that may
be incurred as a result of any state or local law or ordinance relating to the use of your
device.
• This product is designed for mobile phones only. It may not accommodate the weight of a
GPS or other device. Maximum weight of your device should not exceed 1.77 lbs. (0.8 kg).
3
UNIVERSAL VEHICLE MOUNT
www.insigniaproducts.com
Car Window Mount
Holder Front
Holder Back
Release
button
PACKAGE CONTENTS
• Car Air Vent Mount
• Car Window Mount
• Holder
• User Guide
FEATURES
Your Insignia car mount securely holds
a smartphone to your car air vent or car
window. Make sure that your smartphone
is securely fastened to the mount before
you begin your trip.
Caution: This mount is not intended for
extreme o -road use. Excessive bumping
and jarring may result in damage to your
device.
Car Air Vent Mount
Clamps
feet
Swivel
head slot
Clip stopsSpring-loaded clips
Adjustment knob
Hooks
360°
swivel
head
360°
swivel
head
Suction lever
Release button
Adjustment knob
Flexible arm
Suction
cup
Feet
Kickstand
4
www.insigniaproducts.com
UNIVERSAL VEHICLE MOUNT
2 Align the clip stops with the edge of an
air vent louver, slowly push the mount
back until it clicks into place, then
release the mount. Make sure both
hooks are attached to the louver.
3 Position the kickstand so it rests against
other louvers or the dash for support.
4 Loosen the swivel head knob, adjust
the viewing angle, then fully tighten
the knob.
Caution: Do not adjust your Insignia
car mount while driving.
PLACING A SMARTPHONE IN
THE HOLDER
1 Repeatedly press the release button on
the side of the holder. The clamps open.
2 Unfold the feet on the bottom of the
holder.
3 Adjust the clamps to  t the width of
your smartphone.
4 Place your smartphone in the holder
and close the clamps by squeezing
them together tightly until your phone
is secure.
ATTACHING TO AIR VENT
LOUVERS
1 Insert the swivel head into the slot on
the back of the holder and slide it into
place until it is secure.
5
UNIVERSAL VEHICLE MOUNT
www.insigniaproducts.com
ATTACHING TO A CAR
WINDOW
1 Clean the window with a clean cloth.
2 Insert the swivel head into the slot
on the back of holder and slide it into
place until it is secure.
3 Remove the clear  lm from the suction
cup.
4 Push the release button on the
car window mount, press the suction
cup to the desired location on the
clean window, then press the lever
down.
The mount adheres to the window.
5 Loosen the adjustment knob, adjust
the viewing angle, then fully tighten
the knob.
Caution: Always loosen the
adjustment knob before changing the
viewing angle.
6 Bend the  exible arm to further adjust
the viewing angle.
7 To remove the mount, press the
release button, then pull the suction
cup tab.
Caution: Do not adjust your Insignia
car mount while driving.
REMOVING YOUR
SMARTPHONE FROM THE
HOLDER
1 Hold your smartphone and repeatedly
press the release button on the
bottom of the holder. The clamps
open.
2 Remove your smartphone.
6
www.insigniaproducts.com
UNIVERSAL VEHICLE MOUNT
ONE-YEAR LIMITED WARRANTY
Visit www.insigniaproducts.com for details.
CONTACT INSIGNIA
For customer service, call 877-467-4289 (U.S. and Canada) or 01-800-926-3000 (Mexico)
www.insigniaproducts.com
INSIGNIA is a trademark of Best Buy and its a liated companies.
Registered in some countries.
Distributed by Best Buy Purchasing, LLC
7601 Penn Ave South, Rich eld, MN 55423 U.S.A.
©2014 Best Buy. All rights reserved.
Made in China
7
UNIVERSAL VEHICLE MOUNT
www.insigniaproducts.com
(877) 467-4289
www.insigniaproducts.com
INSIGNIA is a trademark of Best Buy and its a liated companies.
Registered in some countries.
Distributed by Best Buy Purchasing, LLC
7601 Penn Ave South, Rich eld, MN 55423 U.S.A.
©2014 Best Buy. All rights reserved.
Made in China
V2 ENGLISH 14-0363
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8

Insignia NS-MVMU5 User manual

Insignia
Brand
Insignia
Model
NS-MVMU5
Type
User manual
This manual is also suitable for
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents