Extron TLP Pro 320C User manual

Brand: Extron

Model: TLP Pro 320C

Category: Processors

Type: User manual

68-2516-01 Rev. A

07 15

TLP Pro 320C

User Guide

TouchLink

TouchLink Pro Touchpanel Control Systems

Safety Instructions • English

WARNING: This symbol,

, when used on the product, is intended

to alert the user of the presence of uninsulated dangerous voltage

within the product’s enclosure that may present a risk of electric shock.

ATTENTION: This symbol,

, when used on the product, is

intended to alert the user of important operating and maintenance

(servicing) instructions in the literature provided with the equipment.

For information on safety guidelines, regulatory compliances, EMI/EMF

compatibility, accessibility, and related topics, see the Extron Safety and

Regulatory Compliance Guide, part number 68-290-01, on the Extron

website, www.extron.com.

Instructions de sécurité • Français

AVERTISSEMENT : Ce pictogramme,

, lorsqu’il est utilisé sur

le produit, signale à l’utilisateur la présence à l’intérieur du boîtier du

produit d’une tension électrique dangereuse susceptible de provoquer

un choc électrique.

ATTENTION : Ce pictogramme,

, lorsqu’il est utilisé sur

le produit, signale à l’utilisateur des instructions d’utilisation ou de

maintenance importantes qui se trouvent dans la documentation

fournie avec le matériel.

Pour en savoir plus sur les règles de sécurité, la conformité à la

réglementation, la compatibilité EMI/EMF, l’accessibilité, et autres sujets

connexes, lisez les informations de sécurité et de conformité Extron,

réf. 68-290-01, sur le site Extron, www.extron.com.

Sicherheitsanweisungen • Deutsch

WARNUNG: Dieses Symbol

auf dem Produkt soll den Benutzer

darauf aufmerksam machen, dass im Inneren des Gehäuses dieses

Produktes gefährliche Spannungen herrschen, die nicht isoliert sind

und die einen elektrischen Schlag verursachen können.

VORSICHT: Dieses Symbol

auf dem Produkt soll dem Benutzer

in der im Lieferumfang enthaltenen Dokumentation besonders wichtige

Hinweise zur Bedienung und Wartung (Instandhaltung) geben.

Weitere Informationen über die Sicherheitsrichtlinien, Produkthandhabung,

EMI/EMF-Kompatibilität, Zugänglichkeit und verwandte Themen finden Sie

in den Extron-Richtlinien für Sicherheit und Handhabung (Artikelnummer

68-290-01) auf der Extron-Website, www.extron.com.

Instrucciones de seguridad • Español

ADVERTENCIA: Este símbolo,

, cuando se utiliza en el producto,

avisa al usuario de la presencia de voltaje peligroso sin aislar dentro del

producto, lo que puede representar un riesgo de descarga eléctrica.

ATENCIÓN: Este símbolo,

, cuando se utiliza en el producto,

avisa al usuario de la presencia de importantes instrucciones de uso y

mantenimiento recogidas en la documentación proporcionada con el

equipo.

Para obtener información sobre directrices de seguridad, cumplimiento

de normativas, compatibilidad electromagnética, accesibilidad y temas

relacionados, consulte la Guía de cumplimiento de normativas y seguridad de

Extron, referencia 68-290-01, en el sitio Web de Extron,

www.extron.com.

Инструкция по технике безопасности • Русский

ПРЕДУПРЕЖДЕНИЕ: Данный символ,

, если указан

на продукте, предупреждает пользователя о наличии

неизолированного опасного напряжения внутри корпуса

продукта, которое может привести к поражению электрическим

током.

ВНИМАНИЕ: Данный символ,

, если указан на продукте,

предупреждает пользователя о наличии важных инструкций по

эксплуатации и обслуживанию в руководстве, прилагаемом к

данному оборудованию.

Для получения информации о правилах техники безопасности,

соблюдении нормативных требований, электромагнитной

совместимости (ЭМП/ЭДС), возможности доступа и других вопросах

см. руководство по безопасности и соблюдению нормативных

требований Extron на сайте Extron: www.extron.com, номер по

каталогу - 68-290-01.

安全说明 • 简体中文

警告： D产品上的这个标志意在警告用户该产品机壳内有暴露的危险电压，

有触电危险。

注意：I 产品上的这个标志意在提示用户设备随附的用户手册中有

重要的操作和维护(维修）说明。

关于我们产品的安全指南、遵循的规范、EMI/EMF 的兼容性、无障碍

使用的特性等相关内容，敬请访问 Extron 网站 www.extron.com，参见 Extron

安全规范指南，产品编号 68-290-01。

安全記事 • 繁體中文

警告: D 若產品上使用此符號，是為了提醒使用者，產品機殼內存在著

可能會導致觸電之風險的未絕緣危險電壓。

注意I 若產品上使用此符號，是為了提醒使用者，設備隨附的用戶手冊中有重要

的操作和維護（維修）説明。

有關安全性指導方針、法規遵守、EMI/EMF 相容性、存取範圍和相關主題的詳細資訊，

請瀏覽 Extron 網站：www.extron.com，然後參閱《Extron 安全性與法規遵守手

冊》，準則編號 68-290-01。

安全上のご注意 • 日本語

警告: この記号 D が製品上に表示されている場合は、筐体内に絶縁されて

いない高電圧が流れ、感電の危険があることを示しています。

注意:この記号 I が製品上に表示されている場合は、本機の取扱説明書に記載されて

いる重要な操作と保守(整備)の指示についてユーザーの注意を喚起するものです。

安全上のご注意、法令遵守、EMI/EMF適合性、その他の関連項目に

ついては、エクストロンのウェブサイト www.extron.com より

『Extron Safety and Regulatory Compliance Guide』 (P/N 68-290-01) をご覧く

ださい。

안전 지침 • 한국어

경고: 이 기호 D, 가 제품에 사용될 경우, 제품의 인클로저 내에 있는

접지되지 않은 위험한 전류로 인해 사용자가 감전될 위험이 있음을

경고합니다.

주의: 이 기호 I, 가 제품에 사용될 경우, 장비와 함께 제공된 책자에 나와

있는 주요 운영 및 유지보수(정비) 지침을 경고합니다.

안전 가이드라인, 규제 준수, EMI/EMF 호환성, 접근성, 그리고 관련 항목에 대한

자세한 내용은 Extron 웹 사이트(www.extron.com)의 Extron 안전 및 규제 준수

안내서, 68-290-01 조항을 참조하십시오.

Safety Instructions

FCC Class A Notice

This equipment has been tested and found to comply with the limits for a Class A digital

device, pursuant to part15 of the FCC rules. The ClassA limits provide reasonable protection

against harmful interference when the equipment is operated in a commercial environment.

This equipment generates, uses, and can radiate radio frequency energy and, if not installed

and used in accordance with the instruction manual, may cause harmful interference to radio

communications. Operation of this equipment in a residential area is likely to cause interference.

This interference must be corrected at the expense of the user.

NOTES:

• This unit was tested with shielded I/O cables on the peripheral devices. Shielded

cables must be used to ensure compliance with FCC emissions limits.

• For more information on safety guidelines, regulatory compliances, EMI/EMF

compatibility, accessibility, and related topics, see the Extron Safety and

Regulatory Compliance Guide on the Extron Website.

Battery Notice

This product contains a battery. Do not open the unit to replace the battery. If the

battery needs replacing, return the entire unit to Extron (for the correct address, see the Extron

Warranty section on the last page of this guide).

CAUTION: Risk of Explosion if the battery is replaced by an incorrect type. Dispose of used

batteries according to the instructions.

ATTENTION : Risque d’explosion. Ne pas remplacer la pile par le mauvais type de pile.

Débarrassez-vous des piles utilisées selon le mode d’emploi.

Trademarks

All trademarks mentioned in this guide are the properties of their respective owners.

The following registered trademarks(

), registered service marks(

), and trademarks(

) are the property of

RGBSystems, Inc. or Extron Electronics:

Registered Trademarks

(

)

AVTrac, Cable Cubby, CrossPoint, eBUS, EDID Manager, EDID Minder, Extron, Flat Field, FlexOS, Global Configurator, GlobalViewer, Hideaway,

Inline, IPIntercom, IPLink, Key Minder, LockIt, MediaLink, PlenumVault, PoleVault, PowerCage, Pure3, Quantum, SoundField, SpeedMount,

SpeedSwitch, SystemINTEGRATOR, TeamWork, TouchLink, V-Lock, VersaTools, VN-Matrix, VoiceLift, WallVault, WindoWall, XTP, and XTP

Systems

Registered Service Mark

(SM)

: S3 Service Support Solutions

Trademarks

(

™

)

AAP, AFL (Accu-Rate Frame Lock), ADSP (Advanced Digital Sync Processing), Auto-Image, CableCover, CDRS (Class D Ripple Suppression),

DDSP (Digital Display Sync Processing), DMI (Dynamic Motion Interpolation), DriverConfigurator, DSPConfigurator, DSVP (Digital Sync

Validation Processing), DTP, eLink, EQIP, FastBite, FOX, FOXBOX, IP Intercom HelpDesk, LinkLicense, MAAP, MicroDigital, NetPA, ProDSP,

QS-FPC (QuickSwitch Front Panel Controller), Room Agent, Scope-Trigger, ShareLink, SIS, Simple Instruction Set, Skew-Free, SpeedNav,

Triple-Action Switching, True4K, Vector, WebShare, XTRA, ZipCaddy, and ZipClip

Conventions Used in this Guide

Notiﬁcations

In this user guide, the following are used:

WARNING: Potential risk of severe injury or death.

AVERTISSEMENT : Risque potentiel de blessure grave ou de mort.

CAUTION: Risk of minor personal injury.

ATTENTION : Risque de blessuremineure.

ATTENTION:

• Risk of property damage.

• Risque de dommages matériels.

NOTE: A note draws attention to important information.

Software Commands

Commands are written in the fonts shown here:

^AR Merge Scene,,Op1 scene 1,1 ^B 51 ^W^C

[01] R 0004 00300 00400 00800 00600 [02] 35 [17] [03]

X1&

X2)

X2#

X2!

}

NOTE: For commands and examples of computer or device responses mentioned

in this guide, the character “0” is used for the number zero and “O” represents the

capital letter “o”.

Computer responses and directory paths that do not have variables are written in the font

shown here:

Reply from 208.132.180.48: bytes=32 times=2ms TTL=32

C:\Program Files\Extron

Variables are written in slanted form as shown here:

ping xxx.xxx.xxx.xxx —t

SOH R Data STX Command ETB ETX

Selectable items, such as menu names, menu options, buttons, tabs, and field names are

written in the font shown here:

From the File menu, select New.

Click the OK button.

Specifications Availability

Product specifications are available on the Extron Website, www.extron.com.

Extron Glossary of Terms

A glossary of terms is available at www.extron.com/technology/glossary.aspx.

Contents

Introduction............................................................ 1

About the TLP Pro 320C ......................................... 1

Features .................................................................. 2

Application Diagram ................................................3

Requirements ..........................................................3

Software .............................................................3

Hardware ............................................................3

Installation Overview ........................................... 4

Mounting ................................................................. 6

Planning .................................................................. 6

Tools Required for Installation .................................. 7

Included Parts ......................................................... 7

Ensure Adequate Under-table Clearance for

Retractors .............................................................. 8

Cutting the Table ..................................................... 8

Cut-out Dimensions ............................................8

Cutting the Surface .............................................8

Running Cables ....................................................10

Installing Cable Retractors (Optional) .....................10

Installing Power Modules (Optional) ....................... 11

Preparing and Installing the AAP Assemblies ......... 12

Installing AAPs ..................................................12

Inserting the AAP Assemblies ............................13

Mounting the TLP Pro 320C Enclosure .................14

Panel Features .................................................... 15

Front Panel Features .............................................15

Connectors ...........................................................17

Power Connector ..............................................17

Network and Power over Ethernet Connector ...19

Setup Menu .......................................................... 21

Status Screen .......................................................22

Network Screen ....................................................23

Display Screen ......................................................26

Audio Screen ........................................................27

Advanced Screen ..................................................28

Calibration Screen ................................................. 29

Conﬁguration Software ..................................... 30

Conﬁguration Software .......................................... 30

Installing GUI Designer, Global Conﬁgurator,

and Toolbelt .....................................................31

Using the Software ............................................31

TLP Pro 320C Web Page ...................................... 32

Updating Firmware ................................................ 33

Downloading Firmware ......................................33

Updating Firmware Using the

Touchpanel Web Page .....................................33

Updating Firmware Using Toolbelt .....................33

Reference Material ............................................. 34

Network Port Requirements ..................................34

IP Link Pro Control Processors ..........................34

TouchLink Pro Touchpanels ...............................35

Global Conﬁgurator Plus and Professional

Software ..........................................................35

Toolbelt Software ..............................................35

TouchLink for iPad (for IP Link Pro

Control Systems) .............................................35

Reset Modes.........................................................36

Use Factory Firmware .......................................36

Reset All IP Settings .......................................... 37

Reset to Factory Defaults ..................................37

Installing or Replacing Buttons ..............................38

Button Replacement .........................................38

Licensed Third-Party Software Used in

the Touchpanels ...................................................39

TLP Pro 320C • Contents v

TLP Pro 320C • Contents vi

Introduction

This guide describes the function, installation, and operation of the Extron TLPPro320C

TouchLink Pro Touchpanel. Unless otherwise stated, the terms “TLP Pro” and “touchpanel”

refer to the TLP Pro 320C.

The TLP Pro 320C is ideal for any AV application requiring a compact, Cable Cubby

touchpanel with a fully customizable interface.

This section provides an overview of these products:

• About the TLP Pro 320C

• Features

• Application Diagram

• Requirements

About the TLP Pro 320C

The Extron TLP Pro 320C is a 3.5 inch Cable Cubby touchpanel with a 320x240 resolution,

flip-up, LCD touchscreen with 18-bit color depth. It combines the AV system control of

TLPProtouchpanels with the cable management convenience of the CableCubby.

The TLP Pro 320C works with any Extron IP Link Pro control processor and is designed for

use in AV system applications that require complete, interactive control of a broad range of

source devices. TouchLink Pro touchpanels operate using standard network infrastructure and

are easy to install with reliable and cost effective Ethernet cable.

Power over Ethernet (PoE) allows the touchpanel to receive power and communications over a

single Ethernet cable.

The TLP Pro 320C is built into an all metal, cable cubby enclosure that can be mounted

securely into a tabletop, lectern, or other flat surface.

The screen layout is designed with the Extron GUI Designer software. This powerful interface

design software offers ready-to-use templates for a wide variety of rooms and presentation

environments. These designs may be used as is, or customized for the application by simply

changing individual graphic elements.

Functions are assigned to the screen objects with the Extron Global Configurator Plus and

Professional software. The ability to define the graphics and the functions associated with them

provides versatility and adaptability to the configuration and control of an AV system.

A light sensor and a speaker provide auto dimming, and audible feedback.

TLP Pro 320C • Introduction 1

Features

3.5 inch flip-up LCD touchscreen — with 320x240 resolution and 18-bit color depth.

Faster processing and more memory — allows for quicker configuration uploads and more

storage for GUI pages.

Ten customizable backlit buttons

Compatible with the full range of Extron IPL Pro and IPCP Pro control processors —

allows easy integration into existing systems.

Power over Ethernet (PoE 802.3af, class3) compliance — allows the touchpanel to

receive power and control over a single Ethernet cable, eliminating the need for a local power

supply. The PoE injector is sold separately.

Highly reliable, energy-efficient external universal power supply — provides worldwide

power compatibility, with high demonstrated reliability and low power consumption for reduced

operating costs. The power supply (part number #70-775-01) is sold separately.

Built-in speaker — mounted in the cable cubby compartment, with improved audio

performance, provides audible feedback from button presses.

Light sensor — adjusts screen brightness as the ambient room lighting changes.

Cable Cubby design — offers easy access to AV, data, and power connections. AC power

modules are available for US, Europe, and other major world markets. AV connectivity options

include:

• Up to 9 single-space AAP-Architectural Adapter Plates.

• Up to 6 Retractor Cable Retraction Systems.

Convenient LED lighting — illuminates power and AV Cable Cubby area.

Integrated lid switch — automatically wakes the touchpanel when opened and can trigger

any other system function.

System connection status indicator — provides visual feedback if the touchpanel is not

communicating with a control processor.

Automatic clock synchronization — allows touchpanel to display the accurate time and

date.

Energy-saving features — adjustable sleep timer puts touchpanel into sleep mode.

Fully customizable using Extron control system software — GUI Designer, Global

Configurator Plus and Professional, and Toolbelt.

Supports Extron Control App and Extron Control for Web.

Contemporary design — complements the aesthetics of any environment. Top surface

available in black anodized or brushed aluminum finishes.

Installation routing template is available.

TLP Pro 320C • Introduction 2

Application Diagram

This diagram shows a typical application for the TLP Pro 320C touchpanel.

LAPTOP

DVD

DOC CAM

AUXILIARY

DISPLAY ON

DISPLAY OFF

MUTE

VOLUME

VideoMore

DVD

ombined

Combined

POWER

12V

--A MAX

Tx Rx RTSCTS

COM 1

Tx Rx

COM 2

VCG

VOL

RELAYS

1 2 C

1 2 3 4 G

DIGITAL I/O

PWR OUT = 6W

eBUS

+V +S

-S

LAN

IPCP PRO 250

IR/S

S G

AUDIO

INPUTS OVER DTP

RS-232

Tx Rx Tx RxG

POWER

12V

0.7A MAX

SIG LINK

DTP OUT

DTP HDMI 330 Rx

OVER DTP

RS-232

Tx Rx Tx RxG

POWER

12V

0.7A MAX

AUDIO

SIG LINK

DTP IN

OUTPUTS

MODEL 80

FLAT PANEL

RS-232

TCP/IP

Network

RS-232

Ethernet Ethernet/PoE

Ethernet HDMI

HDMI

Flat Panel Display

Extron

TLP Pro 320C

3.5" Cable Cubby

TouchLink Pro

Touchpanel

Laptop

Extron

IPCP Pro 250

IP Link Pro

Control

Processor

Extron

DTP HDMI

330 Tx

Transmitter

Ext

ron

DTP

HDMI 330 Rx

Receiv

CATx Cable

up to 330'

(100 m)

Figure 1. Application Diagram

Requirements

Software

For a complete list of the requirements for running GUI Designer, Global Configurator Plus and

Professional, or Toolbelt, see the Extron Web page for the appropriate software.

NOTE: The TLP Pro 320C is not compatible with GlobalConfigurator 3 or

GUIConfigurator.

Hardware

An Extron IP Link Pro control interface must also be connected to the same network domain

as the TouchLink panel. See www.extron.com for a list of suitable controllers.

NOTE: These touchpanels are not compatible with Extron IP Link (non-Pro) controllers.

TLP Pro 320C • Introduction 3

Installation

Overview

1. Before starting, download and install the latest versions of the following software:

 GUI Designer — for designing layouts for Extron TouchLink Pro touchpanels and

third party touch interfaces.

 Global Configurator Plus and Professional — for setting up and conﬁguring the

control processor and touchpanel.

 Toolbelt — provides device discovery, device information, ﬁrmware updates,

and conﬁguration of network settings, system utilities, and user management for

TouchLink Pro devices.

See Configuration Software on page 30.

2. Obtain the following network information from your network administrator:

 DHCP status (on or off). If DHCP is off, you will also require

 IP address

 Subnet mask

 Gateway

 User name — by default, these are either admin or user.

 Passwords — by default, these are either extron (for admin) or the ﬁeld is left blank

(for user).

 MAC address — make a note of the touchpanel MAC address.

3. Prepare to mount the Cable Cubby:

 Make sure you are familiar with all the included parts (see page 7) and have all the

necessary tools (see page 7) for installing the cable cubby.

 Plan where you are going to install the Cable Cubby and how you are going to cut the

hole.

 Ensure the TLP Pro 320C is oriented correctly and that there is adequate room for

cables and cable retractors (optional).

 Ensure you are using the correct cut-out template or dimensions (see Cut-out

Dimensions on page 8).

 Ensure the installation complies with all necessary regulations.

4. Mount the Cable Cubby:

 Cut the table surface (see Cutting the Table on page 8).

 Run all cables to the unit (see Running Cables on page 10).

 Install cable retractors (optional) (see Installing Cable Retractors on page 10).

 Install the power module (optional) (see Installing Power Modules on page 11).

 Put together and install the AAP assembly (see Preparing and Installing the AAP

Assemblies on page 12).

 Mount the Cable Cubby (see Mounting the TLP Pro 320C Enclosure on page14).

TLP Pro 320C • Installation Overview 4

5. Connect cables to the touchpanel. The unit can be powered using a 12 VDC power

supply or a Power over Ethernet (PoE) power injector.

 If required, connect the power supply (see Power Connector on page 17).

 Connect the network cable (see Network and Power over Ethernet Connector on

page 19).

ATTENTION:

• Do not power on the touchpanels or control processors until you have

read the Attention notice on page 18 (12 VDC power supply) or on

page20 (PoE injector).

• Ne branchez pas les écrans tactiles ou les contrôleurs avant d’avoir lu

les mises en garde page18 (source d’alimentation 12VCC) ou page20

(injecteur PoE).

6. Set up the TLP Pro 320C for Network Communication:

 Connect the PC that you will use for setup, the control processor, and the touchpanel

to the same Ethernet subnetwork.

 Use the Setup Menu (see page 21) or the Toolbelt feature of Global Conﬁgurator Plus

and Professional to set the DHCP status and, if necessary, the IP address, subnet

mask, gateway, and related settings for the touchpanel.

7. Conﬁgure the TLP Pro 320C — the GUI Designer Help File, the Global Conﬁgurator Help

File, and the Toolbelt Help File, provide step-by-step instructions and detailed information.

The Global Configurator Help File also includes an introduction to that software and

sections on how to start a project and configuration.

TLP Pro 320C • Installation Overview 5

Mounting

This section describes how to mount the TLP Pro 320C Cable Cubby. It covers:

• Planning

• Tools Required for Installation

• Included Parts

• Ensure Adequate Under-table Clearance for Retractors

• Cutting the Table

• Running Cables

• Installing Cable Retractors (Optional)

• Installing Power Modules (Optional)

• Preparing and Installing the AAP Assemblies

• Mounting the TLP Pro 320C Enclosure

Planning

1. Before making any cuts, select the best location for the TLPPro 320C.

 Ensure that the edge that opens on the lid is oriented correctly.

 Ensure there is enough space for all the system cables and components, above and

below the table. Take account of:

• Clearances for under-table cabling, especially if the cable has a large bend radius.

• Adequate space below the table for cable retractors if they are to be

installed (see page 8).

• The number and type of AAPs required for the installation.

• The location of devices that connect to the AAPs either above or below the table.

2. Verify that you have the correct template or dimensions (see page 8).

3. Decide on the method for cutting a hole in the table (see Cutting the Surface on page 8).

There are three methods available:

• Hand router and template — requires a router template, which must be

purchased separately.

• CNC wood router — must be programmed with the correct dimensions.

• Jigsaw — requires a paper template (available at www.extron.com).

The hand router used with the routing template or the CNC wood router are the most

accurate methods for cutting the hole. Either one of these methods is recommended by

Extron. The jigsaw is less accurate, but is also acceptable.

4. Check all relevant regulations.

 Ensure that the installation complies with local, state, and national building and

electrical codes.

 Ensure that the installation complies with the Americans with Disabilities Act or other

accessibility requirements.

TLP Pro 320C • Mounting 6

Tools Required for Installation

Safety Glasses

Phillips Screw Driver

Tape Measure

1/4" Hex Nut Driver

Marking Pen

Square

Vacuum Cleaner

Figure 2. Tools Required to Install the TLP Pro 320C

Included Parts

Open the shipping container and verify that all the following components are present:

TLP Pro 320C

Table Clamps

AC Power Module*

Blank AAPs

Pass-thru AAPs

Extron

Removal Tool

Zip Ties

#4−40 Screws

and Nuts

2 Pos

AAP Shelf Bracket Kits

(2 brackets/kit)

3 Pos1 Pos

* The unit may be provided without a power module or with a different power module (see the

table below).

US Power

Module

Universal Power

Module

Without Power

Module

AC Power Module

1 1 0

Pass-through AAPs

2,3

4 3 4

Blank AAPs 3 3 5

1-position Bracket Kit

0 1 0

2-position Bracket Kit 2 1 3

3-position Bracket Kit 1 1 1

NOTES:

1 Inside the US, the TLP Pro 320C can be purchased with or without an ACpower

module. Outside the US, see www.extron.com to ﬁnd a power module that is

suitable for your location.

2 Each AAP Bracket Kit consists of two brackets. The rear bracket is higher than the

front bracket and has two holes for screws.

3 Active or Passive AAPs are not provided and must be purchased separately (see

www.extron.com).

4 Single-space brackets can only be installed in one location (see the note and

ﬁgure on page 12).

Figure 3. Parts Included with the TLP Pro 320C

TLP Pro 320C • Mounting 7

Ensure Adequate Under-table Clearance for Retractors

Retractors are optional accessories for handling cables with the TLP Pro 320C. If you are

using retractors, ensure that there is sufficient room beneath the table to accommodate them.

Horizontal mounting provides maximum legroom and protects the retractors from accidental

damage. Vertical mounting is used if space or access makes horizontal mounting difficult. To

satisfy ADA compliance requirements, there is also an option to mount the retractors at a 30°

angle (see the Retractors User Guide, which is available at www.extron.com).

Horizontal Mounting Clearance

XL Models

Vertical Mounting Clearance

XL Models

3.0"

(7.6 cm)

2.7" (6.9 cm)

17.0"

(43.3 cm)

23.0" (58.5 cm)

24.1"

(61.2 cm)

30.1"

(76.5 cm)

2.7" (6.9 cm)

9.8"

(24.9 cm)

3.0"

(7.6 cm)

9.8"

(24.9 cm)

Figure 4. Under-table Clearance Requirements for Retractors

Cutting the Table

Cut-out Dimensions

There are three alternative methods of making the hole for the TLP Pro 320C (see Cutting the

Surface below and on the following page):

• If using a hand router, you should purchase the TLP Pro 320C routing template

(partnumber 70-694-01).

• If using a CNC wood router, use the exact cut-out dimensions.

• If using a reciprocating saw or jigsaw use the paper cut-out template.

Cutting the Surface

WARNING: Wear safety glasses when operating power equipment. Failure to comply

can result in eye injury.

AVERTISSEMENT : Portez des lunettes de sécurité lorsque vous utilisez l’équipement

électrique. Ne pas respecter cela peut conduire à une blessure à l’oeil.

TLP Pro 320C • Mounting 8

ATTENTION:

• The opening in the table for the Cable Cubby should be cut only by licensed and

bonded craftspeople. Exercise care to prevent scarring or damaging the furniture.

• L’ouverture dans la table pour le CableCubby devrait être coupée seulement par

des artisans autorisés et qualiﬁés. Faites attention à ne pas faire de marques sur le

meuble et à ne pas l’endommager.

• Use the appropriate metal Extron routing template or refer to the surface cutout

dimensions before cutting a hole in the furniture or other surface. Pay special

attention to the direction the unit will face. The connector access side is underlined

(see CNC Router below). Extron is not responsible for miscut mounting holes.

• Utilisez le gabarit de détourage métallique approprié ou reportez-vous aux

dimensions de découpe de la surface indiquées ci-après avant de découper

le meuble ou la surface. Faites particulièrement attention à la directions dans

laquelle l’unité sera dirigée. Le côté pour accéder au connecteurs est souligné (voir

CNCRouter ci-dessous). Extron ne sera pas responsable des erreurs de coupe.

• The surfaces of the Cable Cubby enclosure have screws and other protrusions that

could damage ﬁne furniture. Do not rest the enclosure on unprotected furniture.

• La surface du boîtier Cable Cubby a des vis et d’autres éléments en saillie qui

pourrait endommager des meubles ﬁns. N’appuyez pas le boîtier sur du moblier

non protégé.

• Ensure the table surface is at least 0.375 inches (0.95 cm) thick.

• Assurez vous que la surface de la table est au moins 0,95 cm (0,375”) d’épaisseur.

Be certain the cut is laid out in exactly the desired location and the edge that opens on the lid

is correctly oriented. After verifying and checking dimensions, cut a hole in the surface of the

furniture where the enclosure will be installed.

Router with routing template

If using a routing template, make

sure it is the correct template for the

TLPPro 320C (part number 70-694-01).

For complete instructions, see the

RoutingTemplateUserGuide, available at

www.extron.com.

NOTE: The metal router guide must be

purchased separately. It is reusable

and should not be discarded when

the installation is complete.

CNC router

If using a CNC router, enter the correct dimensions for the TLPPro 320C:

7.50 +0.00/-0.02 inches W x 6.00 +0.00/-0.02 inches D

19.05 +0.00/-0.05 cm W x 15.24 +0.00/-0.05 cm D

NOTE: The width dimension (underlined) refers to

the side with AAP access.

Reciprocating saw or jigsaw

If using a reciprocating saw or jigsaw, make

sure to use the paper cutout template for the

TLPPro320C. The template is available at

www.extron.com.

HSA 200

USER ACCESS

HSA 200

CABLE CUBBY 300

USER ACCESS

Cut-Out Template for the Extron

TLP Pro 720C

Outer Edge of Trim Ring

(Do not cut this line.)

1. Confirm the product to be installed.

2. Remove the surface cut-out area

(gray) from the template.

3. Mark the position on the wall or

furniture where the TLP 710MV

is being installed.

4. Cut the opening.

P/N 68-2046-01 Rev. B

Page size: 11" x 17"

Print scale 1:1

Do not shrink.

P/N

TLP Pro 320C • Mounting 9

Running Cables

Run all cables necessary to support the AC connector, the cables stored in the cubby, and all

planned AAP connectors. Run the cables below the table and through the hole that was cut

in the previous step (Cutting the Surface). Leave enough slack in the cables to connect or

route them before the cubby is installed in the table. Leave enough slack for the external power

supply and to connect AV cables and the cable for PoE and LAN to the TLPPro 320C.

Installing Cable Retractors (Optional)

Extron cable retractors retract and store extended cables in Cable Cubby systems, preventing

them from tangling underneath the table. Retractor kits are available for several cable types.

Up to six retractors can be installed in the TLPPro 320C enclosure (three at either end). They

are not provided with the TLPPro 320C and must be purchased separately.

The buttons on the retractors must be placed at one end of the unit and must, therefore, be

the first or the last items added.

Secur

e the bolt

with the nut.

Secure the locking screw

on each retractor.

Do not overtighten.

Insert the bolt thr

ough the

etractor mounting hole on

the side of the Cable Cubby

and r

etractor assembly.

Insert retractors into the

touchpanel enclosure

from underneath.

Figure 5. Installing Cable Retractors

To mount the retractors horizontally and for further information and installation instructions,

see the Retractors User Guide, which is available at www.extron.com. The guide also

provides information about mounting the retractors at a 30° angle to satisfy ADA compliance

requirements.

TLP Pro 320C • Mounting 10

Installing Power Modules (Optional)

WARNING:

AVERTISSEMENT :

• Switch off all electrical power before connecting the AC conduit to a junction box,

and keep power off until installation is complete.

• Débranchez toutes les sources d’alimentation électrique avant de connecter le

conduit d’alimentation à un boîtier d’encastrement, et gardez l’alimentation éteinte

jusqu’à ce que l’installation soit complète.

• If the power cable is installed next to the retractors, ensure the power cable cannot

get tangled in the cable retractor mechanism.

• Si le câble d’alimentation est installé à côté des rétracteurs, assurez vous qu’il ne

puisse pas s’emmêler dans le mécanisme du rétracteur de câbles.

ATTENTION:

• All electrical installation must be performed by qualiﬁed personnel in accordance

with local and national building codes and electrical codes.

• Toute installation électrique, doit être effectuée par un personnel qualiﬁé,

conformément aux codes du bâtiment, aux codes incendie et sécurité, et aux

codes électriques, locaux et nationaux.

NOTE: Different countries require different power adapters. See www.extron.com to

select a power module that is suitable for your location.

The power module takes up two or three AAP spaces and may be installed before or after the

AAP assembly is installed or, if desired, with AAPs on either side.

Secure the po

wer module

to the

TLP Pro 320C frame

with #4-40 Phillips head

scre

ws and star washers.

Figure 6. Installing a Power Module in the TLP Pro 320C

1. Secure the power module with a minimum of two #4-40 Phillips head screws and star

washers.

CAUTION: Risk of electric shock: To ensure proper electrical grounding, use the

provided grounding screws and star washers.

ATTENTION : Risque de choc électrique: Afin d’assurer une mise à la terre

correcte, utilisez les fixations de mise à la terre et les rondelles en étoile fournies.

2. Run the cable or conduit to a convenient junction box. Extron recommends the circuit be

attached to a junction box that is directly wired to the main circuit.

TLP Pro 320C • Mounting 11

Preparing and Installing the AAP Assemblies

The AAP assembly organizes the AAPs onto a frame that can easily be inserted or removed

from the TLPPro 320C enclosure. Pass-through and blank AAP plates are provided with the

TLPPro 320C. Active or passive AAPs must be purchased separately. For the complete range

of available AAPs, see www.extron.com.

If neither power modules nor cable retractors are installed, up to 9 AAPs can be

accommodated. Cable retractors, if installed, occupy the space of two AAP slots. The power

modules occupy the space of two (US) or three (European or Universal) AAP slots.

AAP brackets are available in one-space, two-space, and three-space configurations.

Decide the location of each AAP prior to assembly. Pass-through AAPs provide direct cable

connection and the cable must be installed as they are being mounted on the brackets.

TIP: The recommended way to install the cables and AAPs is to populate the brackets

with AAP plates outside the enclosure as shown in Installing AAPs below, then install

the populated AAP assemblies into the enclosure, as shown in Inserting the AAP

Assemblies on the following page.

NOTE: An extra column of AAP bracket mounting

points is available for use with TLP single-space

AAP mounting brackets (see the illustration to

the right). Single-space brackets will not fit in any

other location.

Rear Bracke

Front Brackets

Figure 7. Preparing the AAP Assembly

Installing AAPs

1. Determine how many AAPs will be used and how many front and rear brackets will be

needed. The brackets come in one-space, two-space, and three-space conﬁgurations.

The rear brackets are taller than the front brackets.

2. Place the AAP onto the bracket. Ensure one end of the AAP is secured to a front bracket

and the other end is secured to a rear bracket. Whenever possible match the width of the

front and rear brackets.

NOTES:

• Active, passive and pass-through AAPs can be mixed.

• Cables can be attached to the active or passive AAPs after assembly.

• Insert cables into each pass-through AAP before the next AAP is added.

The extra column

of mounting points

is for installing

single-space

AAP brackets.

TLP Pro 320C • Mounting 12

3. Attach the AAP loosely to the bracket with the supplied #4-40 captive washer nuts.

NOTE: At this time, captive washer nuts should be hand tightened; otherwise it is

difficult to attach the brackets to the frame of the TLP Pro 320C (see Inserting the

AAP Assemblies below).

When using pass-through AAPs, ensure that the opening in the grommet is accessible for

inserting cables, if required.

4. Insert one cable through the opening of each grommet. Cables can only be inserted into

the pass-through AAP while the front edge is exposed. Securing the next AAP in place

closes the opening on the previous AAP and ensures that the cable cannot escape.

5. Add AAPs until the bracket is ﬁlled. Spaces that are not required can be ﬁlled with blank

AAPs.

Inserting the AAP Assemblies

COMP

UTER

AUDIO

Phillips Head Scre

(secure AAP

assemb

ly)

Tighten down

AAP nuts.

Push assemb

ly through

bottom of enclosure.

Large holes

provide tool

access to fasten

rear brackets.

Figure 8. Inserting the AAP Assemblies

1. Push the ﬁrst AAP assembly through the bottom of the enclosure (

Align the holes in the rear bracket the bottom row of holes on the rear face of the

enclosure and, if necessary, pull any pass-through cables out of the way.

2. Insert a long screwdriver through the large slot in the front panel to secure the rear bracket

to the rear face of the enclosure with the provided #4-40 Phillips head screws (

3. Secure the front bracket to the front face of the enclosure, using the provided #4-40

Phillips head screws.

4. Use a hex nut wrench to tighten the AAP captive washer nuts (

5. Repeat steps 1 through 4 to add each AAP assembly.

6. Run cables to connect the source and output devices to the active and passive AAPs.

TLP Pro 320C • Mounting 13

Mounting the TLP Pro 320C Enclosure

Mount the cable cubby enclosure in the table.

CAUTION: The flanged edges of the top of the surface enclosure are sharp. These

edges are also soft and may be easily nicked or bent. Exercise caution when handling

the enclosure to prevent personal injury or damage to the enclosure.

ATTENTION : Les extrémités à brides du haut de la surface du boîtier sont aiguisées.

Ces extrémités sont aussi lisses et peuvent facilement être coupées ou pliées. Soyez

prudents lorsque vous manipulez le boîtier afin d’éviter de l’endommager ou de vous

blesser.

Figure 9. Mounting the TLP Pro 320C Enclosure

1. Remove the edge grommet protecting the edges of the trim ring(

) and the plastic ﬁlm

on the ﬁnished surfaces.

ATTENTION:

• Do not use isopropyl alcohol or other solvents to clean the Cable Cubby.

Strong solvents will ruin some ﬁnishes.

• Ne pas utiliser de l’alcool isoproprylique ou d’autres solvants pour nettoyer le

CableCubby. Les solvants forts endommageront certaines ﬁnitions.

2. Carefully lower the enclosure into the hole cut in the table (see Cutting the Surface on

page 8). Ensure the trimring(

) is ﬂush with the top of the table.

3. Under the table, attach the table clamps (

) to the pins on each side of the enclosure. It

may be necessary to loosen the wingnuts (

) and the Phillips head screws (

4. Tighten the Phillips head screws until the clamp faces (

) are tightly secured against the

bottom of the table.

5. To prevent the screws from becoming loose, secure the wingnuts against the table clamp

bodies.

TLP Pro 320C • Mounting 14

Page is loading ...

Extron TLP Pro 320C User manual

Brand: Extron

Model: TLP Pro 320C

Category: Processors

Type: User manual

Download PDF

report

Extron TLP Pro 320C User manual

Extron TLP Pro 320C User manual

Related papers

Other documents