Harbor Freight Tools 93660 User manual

Brand: Harbor Freight Tools

Model: 93660

Type: User manual

Harbor Freight Tools 93660 is a 9-foot umbrella with an aluminum pole, making it lightweight and easy to move around. It is made of 100% polyester fabric that is UV treated and mildew resistant, so it can withstand the elements. The umbrella has eight ribs and a 45-degree tilt mechanism, allowing you to adjust the angle of the shade to your liking. It is important to note that this umbrella should only be used with a heavy-duty umbrella stand, which is not included with the product. The umbrella is easy to assemble and disassemble, making it convenient to store when not in use.

9’ UMBRELLA

w/Aluminum Pole

UNPACKING

When unpacking, check to make sure all parts shown on the back of this instruction sheet are included. If any parts are missing or

broken, please call Harbor Freight Tools at the number shown on the front of this sheet as soon as possible.

ASSEMBLY AND OPERATING INSTRUCTIONS

NOTE: All parts below refer to the parts listed on the reverse side of this instruction sheet.

1. Caution: DO NOT attempt to use this Umbrella in moderate or high wind conditions. Doing so may cause personal injury

and/or damage to the Umbrella and personal property. Be careful not to pinch fingers when opening and closing the Umbrella.

2. To assemble, insert Lower Pole (8) with its threaded end upward, securely into a

heavy duty

umbrella stand.

NOTE: This Umbrella is intended for use only with a heavy duty umbrella stand which is not provided with this product.

Adjustable, heavy duty umbrella stands are sold separately by special order from Harbor Freight Tools (SKU 94041).

3. Screw the Connector/Crank (7) onto the threaded end of the Lower Pole.

4. Screw the Upper Pole (6), with its pre-attached upper umbrella assembly, securely into the top of the Connector/Crank.

5. Hand crank the Connector/Crank

clockwise

in order to raise the Hub/Runner (5)

above the self-locking Safety Lock (10), thereby locking the upper umbrella

assembly into place.

The Umbrella is now ready for use.

6. If you wish to tilt the upper part of the umbrella for shade, press the “push

button”. It will tilt to a 45 degree angle. To straighten up, reverse the tilt until the

tilt mechanism “clicks” into place for safety. Note: When tilting, opening, or

closing the umbrella, watch your head for injuries.

See Figure 1.

7. When finished using the Umbrella, crank the Connector/Crank

counterclockwise

until the upper umbrella assembly is completely closed.

CLEANING AND MAINTENANCE

1. To clean, fully open the Umbrella. Wipe with a clean, damp cloth, using a mild soap with water if necessary.

2. Periodically, lightly lubricate all moving parts.

SEE REVERSE SIDE OF THIS INSTRUCTION SHEET FOR PRODUCT WARNINGS,

PRECAUTIONS, PARTS LIST, AND ASSEMBLY DIAGRAM.

3491 Mission Oaks Blvd., Camarillo, CA 93011

Visit our Web site at http://www.harborfreight.com

®.

may be reproduced in any shape or form without the express written consent of Harbor Freight Tools.

93660

Materials:

100% polyester, antique beige

colored fabric. UV treated, mil-

dew resistant with eight ribs, 9

ft. long, and an aluminum pole

with a tilt mechanism that will

angle at a 45 degree angle, left

or right.

Push Button (9)

Hub/Runner (5)

Figure 1

SAFETY WARNINGS AND PRECAUTIONS

1. KEEP PRODUCT USAGE AREA CLEAN.

Cluttered areas invite injuries.

2. KEEP CHILDREN AWAY FROM PRODUCT USAGE

AREA. Do not allow children to handle this product.

3. DO NOT SET UP THIS PRODUCT IF UNDER THE

INFLUENCE OF ALCOHOL OR DRUGS. Read

warning labels on prescriptions to determine if your

judgement or reflexes are impaired while taking drugs.

If there is any doubt, do not attempt to use this product.

4. USE EYE PROTECTION DURING ASSEMBLY.

Wear ANSI approved safety impact eye goggles. The

ANSI approved safety impact goggles are available from

Harbor Freight Tools.

5. DO NOT ATTEMPT TO ASSEMBLE OR USE THIS

PRODUCT IN MODERATE OR HEAVY WIND CONDI-

TIONS. Doing so may cause personal injury and/or

damage to the umbrella

and personal property.

6. CHECK FOR DAMAGED PARTS. Before using this

product, carefully check that it will operate properly and

perform its intended function. Check for damaged parts

and any other conditions that may affect its operation.

Replace or repair damaged or worn parts immediately.

7. MAINTENANCE: Service and maintenance should

be performed regularly by a qualified technician.

8. USE THE RIGHT PRODUCT FOR THE RIGHT

JOB. There are certain applications for which this

product was designed. Use this product

ONLY with

a heavy duty stand, weighing at least 18 Lbs., and

capable of firmly securing this umbrella. Do not use

this product in a way for which it is not intended.

SAVE THIS INSTRUCTION FLYER

You will need this instruction flyer for the Operating

and Maintenance Procedures, Safety Warnings and

Precautions, Parts List and Assembly Diagram. Keep

your invoice with this instruction flyer. Write the invoice

number on the front of this flyer. Keep this

instruction flyer and invoice in a safe and dry place

for future reference.

NOTE: Some parts are listed and shown for illustration

purposes only, and are not available individually as

replacement parts.

PLEASE READ THE FOLLOWING CAREFULLY

THE MANUFACTURER AND/OR DISTRIBUTOR HAS PROVIDED THE PARTS DIAGRAM IN THIS MANUAL AS A REFERENCE

TOOL

ONLY. NEITHER THE MANUFACTURER NOR DISTRIBUTOR MAKES ANY REPRESENTATION OR WARRANTY OF ANY KIND

TO THE BUYER THAT HE OR SHE IS QUALIFIED TO MAKE ANY REPAIRS TO THE PRODUCT OR THAT HE OR SHE IS QUALI-

FIED TO REPLACE ANY PARTS OF THE PRODUCT. IN FACT, THE MANUFACTURER AND/OR DISTRIBUTOR EXPRESSLY

STATES THAT ALL REPAIRS AND PARTS REPLACEMENTS SHOULD BE UNDERTAKEN

BY CERTIFIED AND LICENSED TECHNI-

CIANS AND NOT BY THE BUYER. THE BUYER ASSUMES ALL RISK AND LIABILITY

ARISING OUT OF HIS OR HER REPAIRS TO

THE ORIGINAL PRODUCT OR REPLACEMENT PARTS THERETO, OR ARISING OUT OF HIS OR HER INSTALLATION OF RE-

PLACEMENT PARTS THERETO.

PART # DESCRIPTION QTY

Top Finial

Air Vent

Cover

Rib

Hub/Runner

Upper Pole

Connector/Crank

Lower Poll

Tilt Mechanism

w/ Push Button

PARTS LIST / ASSEMBLY DIAGRAM

Push Button (9)

Harbor Freight Tools 93660 User manual

Harbor Freight Tools 93660 User manual

Harbor Freight Tools 93660 User manual

Related papers

Other documents