Huawei F2A-8K36H Installation guide

Brand: Huawei

Model: F2A-8K36H

Type: Installation guide

6.1

Install guide rails.

Installing Cables

Installing the Device into a Cabinet

6.3

Install mounting brackets.

Device Overview

1 2 Safety Guidelines Site Requirements

3Cabinet Requirements

Adjust the length of one guide rail according to the distance between the front and rear mounting rails, place the guide

rail horizontally at the determined installation position in the cabinet, and hook it to the cabinet's front and rear mounting

rails.

Install M6 screws at the front and rear sides of the guide rail, tighten them to 3 N·m of torque to secure the guide rail to

the cabinet, and then install another guide rail in the same manner.

6.2

Install ﬂoating nuts (for mounting brackets).

6.4

Install the device into the cabinet.

Considering the weight of the device, it is recommended that at

least two persons move it to the cabinet to prevent it from falling

and possibly causing injury.

STAT

BREAKOUT

STAT L/A

CLK

MGMT-ETH

CON/AUX

TOD/CLK-TEST

RST

HP-GE

GE0 GE1

Observe all safety regulations and precautions

NetEngine 8000 F2A-8K36H

Ensure that the guide rails

do not tilt inward.

CAUTION

1.2 N•m

STAT

BREAKOUT

STAT

BREAKOUT

Install two ﬂoating nuts in the positions slightly above the guide rail on each front mounting rail. Install the two ﬂoating

nuts in every other mounting hole.

To secure the mounting brackets to the chassis, use a torque screwdriver to tighten the three M4 cross recessed countersunk

head screws on each of the left and right mounting brackets to 1.2 N·m of torque.

Facing the front of the cabinet, horizontally slide the chassis into the cabinet until the mounting brackets are in close contact

with the mounting rails and aligned with the ﬂoating nuts. Secure the mounting brackets to the cabinet with M6 screws.

3 N•m

7.8 N•m

3 N•m

Floating nuts

Power module

Fan module

Ground terminal

Ground terminal Power side

Port side

Floating nut

Power cable label

ESD wrist strap

Cable tie

Cross recessed countersunk head screw

Cross recessed pan head screw

Signal cable label

Fiber binding tape

Serial cable

Panel screw

Installation accessories:

Tweezer

Insulation tape

Label cable tie

Guide rail

IEC mounting bracket

Figures in the document are for reference only and may be

dierent from actual devices.

When installing a device in a cabinet, ensure that at least 1U

space is reserved above and below the device for appropriate heat

dissipation.

The airﬂow direction of power and fan modules must be the same

as that of the device to which they will be installed. For example,

power and fan modules to be installed on a device that adopts

port-side air intake must also utilize this type of airﬂow, and the

labels on these modules are red. Likewise, power and fan modules

to be installed on a device that adopts port-side air exhaust must

also utilize this type of exhaust, and the labels on these modules

are blue.

NOTE

Item

Weight without

packaging (full

conﬁguration) [kg(lb)]

Power supply speciﬁcations

NetEngine 8000 F2A-8K36H

(Front-to-Rear and Rear-to-Front

Airﬂow)

86.1 mm x 442 mm x 600 mm

(3.39 in. x 17.4 in. x 23.62 in.)

280 mm x 660 mm x 875 mm

(11.02 in. x 25.98 in. x 34.45 in.)

DC power supply: 21 kg (46.30 lb)

Dimensions without packaging

(H x W x D) [mm(in.)]

Dimensions with packaging

(H x W x D) [mm(in.)]

AC power supply: 20.5 kg (45.19 lb)

Rated input voltage:

DC: –48 V to –60 V

AC: 90 V to 120 V(dual-live-wire)

/190 V to 240 V

HVDC: 190 V to 240 V

Input voltage range:

DC: -40 V to -72 V

AC: 90 V to 290 V

HVDC: 190 V to 290 V

Maximum input current:

DC: 50 A AC/HVDC: 16 A

To ensure personal and equipment safety, observe all the safety

precautions on the equipment and in this document.

and items do not cover all

the safety precautions and are only supplementary to the safety

precautions.

Follow all the safety precautions and instructions provided by

Huawei. The safety precautions outlined in this document are only

requirements of Huawei and do not cover general safety regulations.

Huawei is not liable for any consequence that results from violation

of regulations pertaining to safe operations or safety codes

pertaining to design, production, and equipment use.

NOTICE

DANGER WARNING CAUTION

Only trained and qualiﬁed personnel are allowed to install, operate, or

maintain the equipment. Familiarize yourself with all safety

precautions before performing any operation on the equipment.

Personnel Safety

Do not install or remove the equipment or power cables while

power is on.

To ensure equipment and personal safety, ground the equipment

before powering it on.

DANGER

Laser beams will cause eye damage. Do not look into bores of

optical modules or optical ﬁbers without eye protection.

WARNING

Keep an unpacked device upright and handle it with care when

carrying it or installing it into a cabinet.

Do not touch unpainted surfaces of the equipment with wet or

contaminated gloves.

NOTICE

For details about how to install guide rails, see the

installation guide delivered with the guide rails.

Install the guide rails according to the left and right

marks on the guide rails.

NOTICE

Before installing, operating, or maintaining the

equipment, wear an ESD wrist strap and insert

the other end into the ESD jack on the chassis

or cabinet. Remove conductive objects like

jewelry and watches to prevent damages to

the equipment caused by electrostatic

discharge.

ESD protection

The routers must be used indoors. To ensure normal operations and

long service life of the router, the installation site must meet the

following requirements:

The equipment must be installed in a clean, dry, and well ventilated

standard equipment room where temperature can be controlled

within a proper range. The equipment room must be free from

leaking or dripping water, heavy dew, and humidity.

Take dustproof measures in the equipment room. Dust will cause

electrostatic charges on the chassis and aect connections of metal

connectors and joints. This shortens equipment service life and may

cause failures of the router.

The installation site must be free from acidic, alkaline, or other

corrosive gases.

The temperature and humidity in the installation site must be within

allowed ranges.

Item

Long-term operating

temperature [°C(°F)]

Storage temperature

[°C(°F)]

Storage relative

humidity [RH]

Requirement

–40°C to +70°C (–40°F to +158°F)

Port-side intake: –5°C to +45°C (23°F to 113°F)

Port-side exhaust: –5°C to +40°C (23°F to 104°F)

5% to 95% RH, non-condensing

Storage altitude

[m(ft.)] < 5000 m (< 16404.2 ft.)

NOTE

When the altitude is between 1800 m and

4000 m, the highest operating temperature

reduces by 1ºC every time the altitude

increases by 220 m.

Long-term operating

relative humidity [RH] 5% to 90% RH, non-condensing

Short-term operating

relative humidity [RH] 5% to 95% RH, non-condensing

5Power Supply Requirements

For hierarchical power supply protection, the current of each circuit breaker must be at least 16 A when the router adopts AC

power supply. Similarly, the current of each circuit breaker must be at least 50 A if the router adopts DC power supply.

The device supports front-to-rear and rear-to-front heat dissipation

modes. To ensure smooth and ecient heat dissipation, check the

airﬂow direction of the equipment room where the device is to be

installed, and ensure that cold air ﬂows into the device from the air

intake vent and leaves from the air exhaust vent.

The device is air-cooled. The air intake and air exhaust vents must

be free from obstacles, such as labels, to prevent the air intake and

air exhaust vents from being blocked.

You are advised to select the power cable's cross-sectional area

and the device's circuit breaker according to the site survey result.

A 19-inch standard cabinet must be used, with a depth of greater

than or equal to 800 mm (23.62 in.)

For a cabinet with doors, reserve at least 110 mm clearance

between the device's front panel and the cabinet's front door, and

at least 100 mm clearance between the device's rear panel and the

cabinet's rear door. Note that the 110 mm clearance applies to

scenarios where there is no optical attenuator and the optical ﬁbers'

LC connectors are 42 mm long at most. If there are optical

attenuators and the length of the optical ﬁbers' LC connectors is

greater than 42 mm, the clearance is 110 mm plus the cable routing

space for the optical attenuators and optical ﬁbers.

Each cabinet door must have 50% or higher porosity.

The cabinet must meet front-to-rear ventilation requirements.

The cabinet must be equipped with air ﬁlters.

The distance between front and rear mounting rails must be in the

range from 450 mm to 730 mm.

Huawei A610 cabinets are recommended. A self-purchased cabinet

must meet the following requirements:

Dimensions without packaging

(H x W x D)

2200 mm x 600 mm x 1000 mm

(86.61 in. x 23.62 in. x 39.37 in.)

Dimensions with packaging

(H x W x D)

2320 mm x 720 mm x 1290 mm

(91.34 in. x 28.35 in. x 50.79 in.)

The device is inserted into the cabinet from the front of the cabinet.

NOTE

Install the ground cable between the device

and cabinet.

1Install the cabinet ground cable.

Install power cables.

Install DC power cables.

1Install AC or high-voltage DC power cables.

Install ground cables.

Ensure that power cable terminals are properly connected with correct polarity.

DC power cables need to be prepared onsite. For details, see

Install network cables

Before bundling network cables, use a network

cable tester to test cable connectivity.

Bundle the network cables in a rectangle shape.

Ensure that the cable ties are evenly spaced and

face the same direction.

Route cables at a proper distance from each

other. Otherwise, the installation of other cables

may be aected.

Route Ethernet cables, power cables, and

ground cables separately. The Ethernet cables

must not be damaged or broken or have joints.

NOTE

NOTICE

Install optical ﬁbers.

Install corrugated pipes.

1Install optical cable.

Wear an ESD wrist strap or ESD gloves before installing optical modules.

NOTICE

The bending radius of the single-mode G.657A2 optical ﬁber and the multi-mode A1b

optical ﬁber must be greater than or equal to 5D (D: diameter of the optical ﬁber).

Cover empty optical ports and idle optical modules with dust caps.

Do not bundle optical ﬁbers too tightly. You must be able to conveniently remove a

single ﬁber from the bundle.

Properly ﬁx optical ﬁbers onto the cabinet columns to prevent impact on the

surrounding devices.

Route cables.

Do not bundle or route outdoor cables (such as outdoor antenna feeders and

outdoor power cables) and indoor cables together in the cabinet or on the

cable tray.

NOTICE

To route optical ﬁbers along both sides of a device, ensure that at least 110

mm spacing be reserved between the device's front panel and the cabinet's

front door, and at least 100 mm spacing between the device's fan side and

the cabinet's rear door. Note that the 110 mm spacing applies to scenarios

where there is no optical attenuator and the optical ﬁbers' LC connectors are

42 mm long at most. If there are optical attenuators, the spacing is 110 mm

plus the optical attenuator height.

It is recommended that power cables and Ethernet cables are routed at a different side

of the device. Ensure that these cables do not span fan modules.

To facilitate cable routing and maintenance, you are advised to route optical fibers

along both sides of the device, as shown in the figure.

Cable connection table

Select DC power cables based on the types of

terminal blocks used in your equipment

room. For more information, see "DC Power

Cable" in the

Hardware Description.

Select appropriate ﬁbers for optical modules.

For more information, see "Optical Fiber"

and "Optical Module" in the

Hardware Description.

Optical module +

ﬁber jumper

Optical port

NetEngine 8000

Select AC/HVDC power cables based on the

types of power sockets used in your

equipment room. For more information, see

"AC Power Cable" in the

Hardware Description.

No. Item Remarks

Connect To

Chassis

ground

point

Chassis ground cable

4This port connects the router to an operation

terminal or a network management station.

ETH

management

port

Ethernet cable

Terminal block

on the DC

PEM

DC power cable

NetEngine 8000F2A-8K36H

One end of a chassis ground cable is

connected to the ground screw on the

cabinet column, and the other end is

connected to the ground screw on the

chassis.

AC/HVDC power cable

AC/HVDC

power socket

NetEngine 8000

F2A-8K36H

8 9 10

Checking After the Installation Performing a Power-on Check

Before performing a power-on check,

ensure that power switches on the

external power supply system and the

router are turned o.

Check whether the voltage of the input terminal on each power module is

within the normal range. (DC: –40 V to –72 V; AC: 90 V to 290 V)

For more information about indicators, see the .

F2A-8K36H Hardware Description

NOTE

Indicator status when the router is working normally

Component Indicator Status

Power module

Fan module

Management panel

Front system indicator

Steady green

STAT

—Steady green

STAT Steady green

Obtaining Product Documentation

and Technical Support

Power on the device and check whether indicators on the device are normal.

Turn on the external power supply and check whether the output voltage

meets the power supply requirements of the device.

All assembled PGND cables are copper-based, with correct wire diameters. No switch or fuse

is allowed on the cables, and no short circuit occurs.

All ground cables, AC input cables, and intra-cabinet cables are connected correctly

according to the wiring diagram, and all screws are fastened. The input and output cables

are not short-circuited.

Any redundant parts of power cables or PGND cables are trimmed o.

The terminals at both ends of each power cable or PGND cable are crimped securely.

The wiring terminals on cables are wrapped tightly using PVC insulation tapes or heat

shrink tubes.

The wiring terminals with heat shrink tubes are heated using a heat gun.

Flat and spring washers are properly installed on each bolt of a wiring terminal.

All cables, especially the cables in the lower area of the cabinet, are securely connected.

Power and ground cables are bundled and separated from other cables.

The cable layout facilitates future maintenance and expansion.

The labels at both ends of each cable are correct and legible.

All bolts and screws are ﬁrmly fastened, especially on electrical connections. Flat and spring

washers are used with each bolt, and spring washers are placed on the top of ﬂat washers.

Check ItemNo.

WARNING

Trademarks and Permissions

and other Huawei trademarks are trademarks of Huawei Technologies Co., Ltd.

All other trademarks and trade names mentioned in this document are the property of their respective holders.

No part of this document may be reproduced or transmitted in any form or by any means without prior written consent of Huawei Technologies Co., Ltd.

Supplier’s Declaration of Conformity (SDoC)

Unique Identiﬁer: trade name: HUAWEI; product name: Router;

model number: NetEngine 8000 F2A-8K36H routers

Party issuing Supplier’s Declaration of Conformity

Huawei Technologies Co., Ltd.

Bantian, Longgang District,

Shenzhen, 518129, P.R.C

Tel: +86 755 28780808

Responsible Party- U.S. Contact Information

Huawei Technologies USA Inc.

5700 Tennyson Parkway, Suite 600

Plano, Texas 75024

Main: 214-919-6000 / TAC Hotline: 1-877-948-2934

FCC Compliance Statement ( for products subject to Part 15)

This device complies with part 15 of the FCC Rules. Operation is subject to the following

two conditions: (1) This device may not cause harmful interference, and (2) this device

must accept any interference received, including interference that may cause undesired

operation.

Open Source Software Notice

You can view the open source software notice by running the display copyright command in the user view.

Huawei Enterprise

Technical Support

(https://support.huawei..com/enterprise), and select a speciﬁc

product model and version to ﬁnd its documentation.

(https://forum.huawei.com/enterprise) and post your

questions in the community.

For enterprise users:

(https://support.huawei.com/carrier), and select a speciﬁc

product model and version to ﬁnd its documentation.

(https://forum.huawei.com/carrier) and post your questions in

the community.

For carrier usesrs:

Huawei Carrier

Technical Support

STAT

BREAKOUT

STAT

BREAKOUT

STAT L/A

CLK

MGMT-ETH

CON/AUX

TOD/CLK-TEST

RST

HP-GE

GE0 GE1

STAT L/A

CLK

MGMT-ETH

CON/AUX

TOD/CLK-TEST

RST

HP-GE

GE0 GE1

STAT L/A

CLK

MGMT-ETH

CON/AUX

TOD/CLK-TEST

RST

HP-GE

GE0 GE1

STAT L/A

CLK

MGMT-ETH

CON/AUX

TOD/CLK-TEST

RST

HP-GE

GE0 GE1

STAT L/A

CLK

MGMT-ETH

CON/AUX

TOD/CLK-TEST

RST

HP-GE

GE0 GE1

STAT

BREAKOUT

STAT

BREAKOUT

STAT

BREAKOUT

Power cable Ethernet cable

Power cable

STAT L/A

CLK

MGMT-ETH

CON/AUX

TOD/CLK-TEST

RST

HP-GE

GE0GE1

Front Rear

Long-term operating

altitude < 4000 m (< 13123.4 ft.)

110 V AC power supply requires dual-live-wire

input.

NetEngine 8000 F2A-8K36H Hardware

Description

STAT L/A

CLK

MGMT-ETH

CON/AUX

TOD/CLK-TEST

RST

HP-GE

GE0 GE1

CAUTION

Issue: 01

Part Number:31500GBC

Scan to Watch Quick Installation Guide

NetEngine 8000 F2A-8K36H

Quick Installation Guide

Huawei F2A-8K36H Installation guide

Huawei F2A-8K36H Installation guide

Huawei F2A-8K36H Installation guide

Related papers

Other documents