Dell W-7200 is a high-performance switch that provides advanced Layer 2 and Layer 3 switching capabilities for enterprise networks. It offers wire-speed performance, high port density, and robust security features, making it ideal for data centers, campus networks, and service provider environments. With its modular design and flexible configuration options, the Dell W-7200 can be tailored to meet the specific needs of your network.
Dell W-7200 is a high-performance switch that provides advanced Layer 2 and Layer 3 switching capabilities for enterprise networks. It offers wire-speed performance, high port density, and robust security features, making it ideal for data centers, campus networks, and service provider environments. With its modular design and flexible configuration options, the Dell W-7200 can be tailored to meet the specific needs of your network.
Dell PowerConnect W-Series SFP/SFP+
Installation Guide
0510792-03 | February 2013 1
Introduction
SFP modules, small form-factor pluggable modules, also known as mini-GBICs, are hot-swappable Gigabit
Ethernet optical transceivers. SFP+ modules, small form-factor pluggable modules, are hot-swappable 10 Gigabit
Ethernet optical transceivers.
SFP-TX: conforms to 1000Base-T copper wiring Gigabit Ethernet standard
SFP-SX: conforms to 1000Base-SX fiber optic Gigabit Ethernet standard
SFP-LX: conforms to 1000Base-LX fiber optic Gigabit Ethernet standard
SFP-10GE-SR: conforms to 10GEBase-SR fiber optic Gigabit Ethernet standard
SFP-10GE-LR: conforms to 10GEBase-LR fiber optic Gigabit Ethernet standard
SFP-10GE-LRM: conforms to 10GEBase-LRM fiber optic Gigabit Ethernet standard
Specifications
Figure 1 shows the physical form factor of the copper and fiber based SFP modules.
Figure 1
SFP Module Form Factor
SFP-TX
Table 1 describes the specifications for the SFP-TX module.
NOTE: Approved optics are tested and supported within Dell controller systems. Non-approved, third party optics are not tested or
supported; therefore, proper functionality of non-approved, third party optics are not guaranteed. For a complete list of approved
optics, contact your Dell sales representative.
Parameter Specification
Connector Type RJ-45
Cable Type and Maximum Range Cat 5, 5E, 6/Range up to 100 m
arun_0110
Copper SFP
Form Factor
Fiber SFP
Form Factor
2 Dell PowerConnect W-Series SFP/SFP+ | Installation Guide
SFP-SX
Table 2 describes the specifications for the SFP-SX module.
SFP-LX
Table 3 describes the specifications for the SFP-LX module.
SFP-10GE-SR
Table 4 describes the specifications for the SFP-10GE-SR module.
SFP-10GE-LR
Table 5 describes the specifications for the SFP-10GE-LR module.
Parameter Specification
Connector Type LC fiber optic
Cable Type and Maximum Range 62.5 m multi-mode fiber/Range up to 260 m (850 feet)
50 m multi-mode fiber/Range up to 550 m (1800 feet)
Input Wavelength 770 to 860 nm
Center Wavelength 830 to 860 nm
Parameter Specification
Connector Type LC fiber optic
Cable Type and Maximum Range 9 m single-mode fiber/Range of 10 km (6.21 miles)
Input Wavelength 1260 nm to 1570 nm
Center Wavelength 1310 nm
Parameter Specification
Connector Type LC fiber optic
Cable Type and Maximum Range 62.5 m multi-mode fiber with 160 MHz/km (FDDI) cable has a range of 26 m (85.3 feet)
62.5 m multi-mode fiber with 200 MHz/km (OM1) cable has a range of 33 m (108.3 feet)
50 m multi-mode fiber with 400 MHz/km cable has a range of 66 m (216.5 feet)
50 m multi-mode fiber with 500MHz/km (OM2) cable has a range of 82 m (269 feet)
50 m multi-mode fiber with 2000 MHz/km (OM3) cable has a range of 300 m (984.3 feet)
Input Wavelength 840 nm to 860 nm
Center Wavelength 850 nm
Parameter Specification
Connector Type LC fiber optic
Cable Type and Maximum Range 9 m single-mode fiber/Range of 10 km (6.21 miles)
Input Wavelength 1280 nm to 1340 nm
Dell PowerConnect W-Series SFP/SFP+ | Installation Guide 3
SFP-10GE-LRM
Table 6 describes the specifications for the SFP-10GE-LRM module
SFP/SFP+ Installation
To install an SFP/SFP+ module:
1. Use standard ESD precautions when installing the module.
2. Slide the module into a 1000Base-X port for SFP or a 10GBase-X port for SFP+ of the controller until a
connection is made and an audible click is heard.
3. Lock the module in place by moving the latch on the module to an upright position, facing the top of the
module.
LC Fiber Optic Cable Connection
To connect an LC fiber optic cable into an SFP-SX , SFP-LX, or SFP+ module:
1. Insert the fiber optic cable into the module. Ensure that the latch on the cable faces the top of the module.
2. Slide the cable into place until a connection is made and an audible click is heard.
To disconnect an LC fiber optic cable from the module:
1. Depress to release the latch on the cable and simultaneously pull the cable out of the port.
SFP/SFP+ Removal
To remove an SFP/SFP+ module:
1. Use standard ESD precautions when removing the module.
2. Open and release the latch on the module.
3. Pull and remove the module from the port.
Center Wavelength 1310 nm
Parameter Specification
Connector Type LC fiber optic
Cable Type and Maximum Range 50 m multi-mode fiber with 500MHz/km (OM2) or 2000MHz/km (OM3) cable has a range
of 220 m (721.8 feet)
50 m multi-mode fiber with 400 MHz/km cable has a range of 100 m (328.1 feet)
62.5 m multi-mode fiber with 160 MHz/km (FDDI) or 200 MHz/km (OM1) cable has a
range 220 m (721.8 feet)
Input Wavelength 1260 nm to 1355 nm
Center Wavelength 1310nm
Parameter Specification
Copyright
© 2013 Aruba Networks, Inc. Aruba Networks trademarks include , Aruba Networks
®
, Aruba Wireless Networks
®
, the
registered Aruba the Mobile Edge Company logo, and Aruba Mobility Management System
®
. Dell™, the DELL™ logo, and PowerConnect™ are
trademarks of Dell Inc.
All rights reserved. Specifications in this manual are subject to change without notice.
Originated in the USA. All other trademarks are the property of their respective owners.
Open Source Code
Certain Aruba products include Open Source software code developed by third parties, including software code subject to the GNU General
Public License (GPL), GNU Lesser General Public License (LGPL), or other Open Source Licenses. The Open Source code used can be found at
this site:
http://www.arubanetworks.com/open_source
Legal Notice
The use of Aruba Networks, Inc. switching platforms and software, by all individuals or corporations, to terminate other vendors’ VPN client
devices constitutes complete acceptance of liability by that individual or corporation for this action and indemnifies, in full, Aruba Networks, Inc.
from any and all legal actions that might be taken against it with respect to infringement of copyright on behalf of those vendors.
4 Dell PowerConnect W-Series SFP/SFP+ | Installation Guide
Contacting Support
Website Supportain Website
Main Site dell.com
Support Site dell.com/support
Documentation Site dell.com/support/manuals
-
1
-
2
-
3
-
4
Dell W-7200 is a high-performance switch that provides advanced Layer 2 and Layer 3 switching capabilities for enterprise networks. It offers wire-speed performance, high port density, and robust security features, making it ideal for data centers, campus networks, and service provider environments. With its modular design and flexible configuration options, the Dell W-7200 can be tailored to meet the specific needs of your network.
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI
Related papers
Other documents
-
Extreme Networks 10018 User manual
-
Cisco SFP-H10GB-CU5M Datasheet
-
Avaya AA1419074-E6 Datasheet
-
Juniper EX3200 Series User manual
-
Juniper EX-SFP-GE40KT15R13 Datasheet
-
-
Juniper Networks EX3200 User manual
-
Netgear GS728TXS-100NES Datasheet
-
-