H3C S9500 Series Operating instructions

Brand: H3C

Model: S9500 Series

Type: Operating instructions

H3C S9500 Series: Unleash the Power of Connectivity and Remote Powering

The H3C S9500 Series Routing Switches are designed to provide robust and versatile networking solutions for various applications. With its advanced features and capabilities, this series offers exceptional connectivity, flexibility, and power management options:

Seamless Connectivity: Equip your network with Gigabit Ethernet ports to establish high-speed connections. Connect diverse devices such as IP phones, wireless access points, and surveillance cameras to create a comprehensive and reliable network infrastructure.

H3C S9500 Series: Unleash the Power of Connectivity and Remote Powering

Seamless Connectivity: Equip your network with Gigabit Ethernet ports to establish high-speed connections. Connect diverse devices such as IP phones, wireless access points, and surveillance cameras to create a comprehensive and reliable network infrastructure.

Operation Manual – PoE

H3C S9500 Series Routing Switches Table of Contents

Table of Contents

Chapter 1 PoE Configuration.......................................................................................................1-1

1.1 PoE Overview....................................................................................................................1-1

1.1.1 PoE on the Switch...................................................................................................1-1

1.1.2 External PSE4500-A Power System.......................................................................1-2

1.1.3 PoE-Capable Card..................................................................................................1-2

1.2 PoE Configuration..............................................................................................................1-2

1.2.1 PoE Configuration Tasks ........................................................................................1-2

1.3 Comprehensive Configuration Example............................................................................1-4

Chapter 2 PoE PSU Supervision Configuration......................................................................... 2-1

2.1 Introduction to PoE PSU Supervision................................................................................2-1

2.2 AC Input Alarm Thresholds Configuration.........................................................................2-1

2.2.1 AC Input Alarm Thresholds Configuration Tasks....................................................2-1

2.2.2 AC Input Alarm Thresholds Configuration Example ............................................... 2-2

2.3 DC Output Alarm Thresholds Configuration......................................................................2-2

2.3.1 DC Output Alarm Thresholds Configuration Tasks.................................................2-2

2.3.2 DC Output Alarm Thresholds Configuration Example ............................................2-3

2.4 Displaying PoE Supervision Information ...........................................................................2-3

2.5 PoE PSU Supervision Configuration Example..................................................................2-4

Operation Manual – PoE

H3C S9500 Series Routing Switches Chapter 1 PoE Configuration

1-1

Chapter 1 PoE Configuration

1.1 PoE Overview

1.1.1 PoE on the Switch

H3C S9500 Series Routing Switches (hereinafter referred to as S9500 series) support

power-over-Ethernet (PoE). Equipped with external power supply and PoE-capable

cards, S9500 series can provide 48 VDC power for remote powered devices (PDs,

such as IP phones, WLAN APs, and Network cameras) through twisted pairs.

z The S9500 series support LEGACY Power Supply standard. While they can also

supply power to PDs noncompliant with the standard.

The power supply of the S9500 series is administered by the SRP card; each PoE card

on the switch can be viewed as a power sourcing equipment (PSE), which administers

the power supplying of all the ports on it independently.

The S9500 series can transmit data and supply power in the mean time through the

signal lines (1, 3, 2, and 6) of the category-3/5 twisted pairs. Using converters, they can

also supply power to the PDs that can be powered only through spare lines (4, 5, 7, and

8).

z The S9500 series supply power through the Ethernet electrical ports on the

service cards. Each service card can supply power to up to 48 remote devices at

the maximum distance of 100 m (328 feet).

z The maximum power that can be supplied by each Ethernet port to its PD is 16.8

z When supplying power to remote devices, the maximum total power that can be

provided by the S9500 series is 4500 W (220 V)/2250 W (110V). The switch

determines whether or not to supply power to the next remote PD it discovered

depending on the total power it currently supply.

 Note:

z When a remote PD is powered by an S9500 series switch, the PD needs not have

any external power supply.

z If the remote PD has an external power supply, the S9500 series switch and the

external power supply will be redundant with each other for the PD.

Operation Manual – PoE

H3C S9500 Series Routing Switches Chapter 1 PoE Configuration

1-2

1.1.2 External PSE4500-A Power System

If PSE4500-A power system is taken as the external power supply of the switch, the

power distribution is as follows:

1) Input voltage: 110 VAC

z One or two PSUs (power supply unit) of the PSE4500-A power system can provide

1200 W of power.

z If the PSE4500-A power modules work in 2+1 redundancy backup mode, then

each module provides 750 W of power.

2) Input voltage: 220 VAC

z One or two PSUs of the PSE4500-A power system can provide 2500 W of power.

z If the PSE4500-A power modules are in 2+1 redundancy, then each module

provides a power of 1500 W.

1.1.3 PoE-Capable Card

The following service card of the S9500 series supports PoE:

z GV48D

1.2 PoE Configuration

The S9500 series can automatically detect any connected device that needs remote

power supply and feeds power to this device.

z Depending on your actual network requirement, you can set the maximum PoE

power totally supplied by the switch through the command line.

z You can set the maximum PoE power supplied by a card through the command

line.

z You can also control the PoE on each PoE port independently through the

command line. The control includes: enabling/disabling the PoE feature, and

setting the maximum PoE power, the PoE mode and the PoE priority on the port.

1.2.1 PoE Configuration Tasks

The following table describes the PoE configuration tasks on the S9500 series.

Table 1-1 PoE configuration tasks on the S9500 series

No Item Command Description

Enter system

view

system-view

Enter Ethernet

port view

interface interface-type

interface-number

As a result of this

command, a port view

prompt is displayed, which

varies with the port type

you selected.

Operation Manual – PoE

H3C S9500 Series Routing Switches Chapter 1 PoE Configuration

1-3

No Item Command Description

Enable PoE on

the port

poe enable

By default, PoE is disabled

on a port.

Set the maximum

PoE power

supplied by the

port

poe max-power

max-power

You can set the maximum

PoE power supplied by a

port depending on the

power of the actual PD. By

default, the max-power is

16800 mW.

Set the PoE

mode on the port

poe mode { signal |

spare | auto }

S9500 series supports

only signal line PoE mode.

By default, the PoE mode

on a port is signal.

Set the PoE

priority on the

port

poe priority { critical |

high | low }

You can set the PoE

priority on a port

depending on the practical

situation. By default, the

PoE priority on a port is

low.

Display the PoE

state of a specific

or all ports of the

switch

display poe interface

[ interface-name |

interface-type

interface-num ]

You can execute this

command in any view.

Executing the display poe

interface command

without any option displays

the PoE status of all the

ports.

Display the PoE

power

information of a

specific or all

ports of the

switch

display poe interface

power [ interface-name |

interface-type

interface-num ]

You can execute this

command in any view.

Executing the display poe

interface power

command without any

option displays the PoE

power information about

all the ports.

Display the PoE

status and PoE

power

information of

each card

display poe pse

You can execute this

command in any view

To cancel the configurations, use the corresponding undo commands. For details

about the parameters, refer to the Command Manual.

Operation Manual – PoE

H3C S9500 Series Routing Switches Chapter 1 PoE Configuration

1-4

 Note:

z Before setting the maximum power supplied by a card, make sure the remaining

power of the switch is no less than the full power of the card, and the power you can

set for a card ranges from 37 W to 806 W.

z The reserved power for a blank slot will be recycled automatically by the system if

you insert a PoE-incapable card into the slot.

z When a card is almost fully loaded and a new PD is added, the switch will respond to

the PD according to the PoE priority set on the port.

z The PoE priority of each port is based on its card. In other words, the switch cannot

compare the priorities of ports on different cards.

z The sampling cycle of the power, current and voltage of ports is 1 second; the

sampling cycle of the peak power and average power of both cards and ports is 5

minutes

1.3 Comprehensive Configuration Example

I. Network requirements

z Two PoE-capable cards are installed in slots 3 and 5 on an S9500 series routing

switch.

z GigabitEthernet3/1/1 through GigabitEthernet3/1/48 are connected with IP

phones and GigabitEthernet5/1/1 through GigabitEthernet5/1/48 are connected

with access point (AP) devices.

z The IP phones connected to GigabitEthernet3/1/23 and GigabitEthernet3/1/24 do

not need PoE.

z GigabitEthernet3/1/48 is reserved for the use of network management, so it needs

higher priority.

z Slot 3 is provided with 400 W power and slot 5 is provided with full power.

z The input power of the AP device connected to GigabitEhternet5/1/15 cannot be

greater than 9000 mW.

Operation Manual – PoE

H3C S9500 Series Routing Switches Chapter 1 PoE Configuration

1-5

II. Network diagram

IP Phone

NETWORK

S9500

GigabitEthernet3/1/1 -

GigabitEthernet3/1/48

IP Phone

GigabitEthernet5/1/1 -

GigabitEthernet5/1/48

IP Phone

GigabitEthernet3/1/1 -

GigabitEthernet3/1/48

IP Phone

GigabitEthernet5/1/1 -

GigabitEthernet5/1/48

IP Phone

NETWORK

S9500

GigabitEthernet3/1/1 -

GigabitEthernet3/1/48

IP Phone

NETWORK

S9500

GigabitEthernet3/1/1 -

GigabitEthernet3/1/48

IP Phone

GigabitEthernet5/1/1 -

GigabitEthernet5/1/48

IP Phone

GigabitEthernet3/1/1 -

GigabitEthernet3/1/48

IP Phone

GigabitEthernet5/1/1 -

GigabitEthernet5/1/48

IP Phone

GigabitEthernet3/1/1 -

GigabitEthernet3/1/48

IP Phone

GigabitEthernet5/1/1 -

GigabitEthernet5/1/48

Figure 1-1 PoE remote power supplying

III. Configuration procedure

# Set the maximum power to 400 W on the card in slot 3. By default, the power of each

card is full, so the power on the card in slot 5 need not be configured.

[H3C] poe max-power 400 slot 3

# Enable PoE on the ports GigabitEthernet3/1/1 through GigabitEthernet3/1/48.

[H3C-GigabitEthernet3/1/1] poe enable

[H3C-GigabitEthernet3/1/2] poe enable

[H3C-GigabitEthernet3/1/3] poe enable

Go on the configuration till the port GigabitEthernet3/1/48.

# Enable PoE on the ports GigabitEthernet5/1/1 through GigabitEthernet5/1/48.

[H3C-GigabitEthernet5/1/1] poe enable

[H3C-GigabitEthernet5/1/2] poe enable

[H3C-GigabitEthernet5/1/3] poe enable

Go on the configuration till the port GigabitEthernet5/1/48.

# Set the PoE priority of the port GigabitEthernet3/1/48 to critical, the PD connected

with GigabitEthernet3/1/48 will be powered in precedence on the premise that other

ports' power supplying is not interrupted.

[H3C-GigabitEthernet3/1/48] poe priority critical

# Set the maximum PoE power on the GigabitEthernet5/1/15 port to 9000 mW.

[H3C] interface GigabitEthernet5/1/15

[H3C-GigabitEthernet5/1/15] poe max-power 9000

Operation Manual – PoE

H3C S9500 Series Routing Switches Chapter 2 PoE PSU Supervision Configuration

2-1

Chapter 2 PoE PSU Supervision Configuration

2.1 Introduction to PoE PSU Supervision

The PoE-capable S9500 series can monitor the external PoE PSUs through the power

supervision module on the PoE external power system.

The PoE PSU supervision module enables you to:

z Set the alarm thresholds for the AC input voltages of the PoE PSUs.

z Set the alarm thresholds for the DC output voltages of the PoE PSUs.

z Query PSU information such as voltage and power.

2.2 AC Input Alarm Thresholds Configuration

You can set the AC input alarm thresholds for the PoE PSUs to enable the S9500

series to monitor the AC input voltages of the PSUs in real time through the PoE

supervision module.

2.2.1 AC Input Alarm Thresholds Configuration Tasks

Table 2-1 AC input alarm thresholds configuration tasks

No Item Command Description

1 Enter system view

system-view

Set the overvoltage alarm

threshold of AC input (upper

threshold) for the PoE PSUs

poe-power

input-thresh

upper string

Required, and the max

voltage is 264.0 V.

Set the undervoltage alarm

threshold of AC input (lower

threshold) for the PoE PSUs

poe-power

input-thresh

lower string

Required, and the min

voltage is 90.0 V.

Display the AC input state of

each PoE PSU

display

poe-power

ac-input state

Optional, and you can

execute this command

in any view.

Operation Manual – PoE

H3C S9500 Series Routing Switches Chapter 2 PoE PSU Supervision Configuration

2-2

 Note:

z You can set the thresholds to any appropriate values in the range, but make sure

the lower threshold is less than the upper threshold.

z For 220 VAC input, it is recommended to set the upper threshold to 264 V and the

lower threshold to 181 V.

z For 110 VAC input, it is recommended to set the upper threshold to 132 V and the

lower threshold to 90 V.

2.2.2 AC Input Alarm Thresholds Configuration Example

I. Network requirements

z Set the overvoltage alarm threshold of AC input for PoE PSUs to 264.0 V.

z Set the undervoltage alarm threshold of AC input for PoE PSUs to 181.0 V.

II. Configuration procedure

# Enter system view.

<H3C> system-view

# Set the overvoltage alarm threshold of AC input for PoE PSUs to 264.0 V.

[H3C] poe-power input-thresh upper 264.0

# Set the undervoltage alarm threshold of AC input for PoE PSUs to 181.0 V.

[H3C] poe-power input-thresh lower 181.0

# Display the information about the AC input for the PoE PSUs.

[H3C] display poe-power ac-input state

2.3 DC Output Alarm Thresholds Configuration

You can set the DC output alarm thresholds for the PoE PSUs to enable the S9500

series to monitor the DC output voltages of the PSUs in real time through the PoE

supervision module.

2.3.1 DC Output Alarm Thresholds Configuration Tasks

Table 2-2 DC output alarm thresholds configuration tasks

No Operation Command Description

1 Enter system view

system-view

Set the overvoltage alarm

threshold of DC output (upper

threshold) for the PoE PSUs

poe-power

output-thresh upper

string

Required, and the

range is 55.0 V to

57.0 V.

Operation Manual – PoE

H3C S9500 Series Routing Switches Chapter 2 PoE PSU Supervision Configuration

2-3

Set the undervoltage alarm

threshold of DC output (lower

threshold) for the PoE PSUs

poe-power

output-thresh lower

string

Required, and the

range is 45.0 V to

47.0 V.

Display the DC output state

of the PoE PSUs.

display poe-power

dc-output state

Optional, and you

can execute this

command in any

view.

Display the DC output

voltage/current value of the

PoE PSUs

display poe-power

dc-output value

Optional, and you

can execute this

command in any

view.

 Note:

For both 220 VAC and 110 VAC input, it is recommended to set the upper threshold to

57.0 V and the lower threshold to 45.0 V.

2.3.2 DC Output Alarm Thresholds Configuration Example

I. Network requirements

z Set the overvoltage alarm threshold of DC output for the PoE PSUs to 57.0 V.

z Set the undervoltage alarm threshold of DC output for the PoE PSUs to 45.0 V.

II. Configuration procedure

# Enter system view.

<H3C> system-view

# Set the overvoltage alarm threshold of DC output for the PoE PSUs to 57.0 V.

[H3C] poe-power output-thresh upper 57.0

# Set the undervoltage alarm threshold of DC output for the PoE PSUs to 45.0 V.

[H3C] poe-power output-thresh lower 45.0

# Display the DC output state of the PoE PSUs.

[H3C] display poe-power dc-output state

# Display the DC output voltage/current values of the PoE PSUs.

[H3C] display poe-power dc-output value

2.4 Displaying PoE Supervision Information

After completing the above configurations, you can execute the display command in

any view to query the PoE state of the switch. Then you can view the display output to

check the effect of these configurations.

Operation Manual – PoE

H3C S9500 Series Routing Switches Chapter 2 PoE PSU Supervision Configuration

2-4

Table 2-3 Display PoE supervision information

No Operation Command Description

Display the basic information

about the PoE PSUs.

display

supervision-module

information

You can execute

this command in

any view.

Display detailed alarm

information about the PoE

PSUs.

display poe-power

alarm

You can execute

this command in

any view.

Display the number and

current state of AC power

distribution switches of the

PSUs.

display poe-power

switch state

You can execute

this command in

any view.

For details about display output, refer to the Command Manual.

2.5 PoE PSU Supervision Configuration Example

I. Network requirements

z Insert a PoE-capable card into slot 3 of the S9500 series routing switch.

z Connect GigabitEthernet3/1/1 to GigabitEthernet3/1/48 to IP phones.

z Set the AC input and DC output alarm thresholds to appropriate values.

II. Network diagram

Network

S9500

IP Phone

Network Network

IP Phone

GigabitEthernet3/1/1 -GigabitEthernet3/1/48

Network

S9500

IP Phone

Network Network

IP Phone

Network

S9500

IP Phone

Network Network

IP Phone

GigabitEthernet3/1/1 -GigabitEthernet3/1/48

Figure 2-1 Network diagram for PoE supervision configuration

III. Configuration procedure

# Enter system view.

<H3C> system-view

Operation Manual – PoE

H3C S9500 Series Routing Switches Chapter 2 PoE PSU Supervision Configuration

2-5

# Set the overvoltage alarm threshold of AC input for PoE PSUs to 264.0 V.

[H3C] poe-power input-thresh upper 264.0

# Set the undervoltage alarm threshold of AC input for PoE PSUs to 181.0 V.

[H3C] poe-power input-thresh lower 181.0

# Set the overvoltage alarm threshold of DC output for the PoE PSUs to 57.0 V.

[H3C] poe-power output-thresh upper 57.0

# Set the undervoltage alarm threshold of DC output for the PoE PSUs to 45.0 V.

[H3C] poe-power output-thresh lower 45.0

H3C S9500 Series Operating instructions

Brand: H3C

Model: S9500 Series

Type: Operating instructions

H3C S9500 Series: Unleash the Power of Connectivity and Remote Powering

Seamless Connectivity: Equip your network with Gigabit Ethernet ports to establish high-speed connections. Connect diverse devices such as IP phones, wireless access points, and surveillance cameras to create a comprehensive and reliable network infrastructure.

Download PDF

report

H3C S9500 Series Operating instructions

H3C S9500 Series Operating instructions

Related papers

Other documents