Extron NAV 10E 101 User guide

Category
Network switches
Type
User guide
NAV Pro AV Over IP Solutions
Minimum Network Requirements & Guidelines – 1G Infrastructures
The NAV
AV over IP platform uses standard 1G and 10G networks. Below are minimum requirements and
guidelines to ensure a successful implementation for a 1G system. For 10G system requirements, please see
the other side.
Minimum Network Requirements – 1G Systems
Implementation Considerations
Devices can be installed on a physically isolated network or converged onto existing Gbps networks
For streaming on a private network use the 239.255.0.0 to 239.255.255.255 range which is reserved
for administratively scoped addressing
Category 5e or 6 Ethernet network cable for Gbps speeds up to 100m
Network Switch Hardware
1 Gbps port for every connected NAV 1G endpoint
IGMPv2 or IGMPv3 implemented
Layer 2+ or 3
Ensure switch supports non-blocking backplane/chassis
If applicable, use switches that support 802.1x for endpoint authentication
Network Switch Settings
IGMPv2 or IGMPv3 snooping enabled on all switches and VLANs
IGMPv2 or IGMPv3 querier enabled on one of the switches if no router is present
IGMP Immediate Leave/Fast Leave enabled
802.3az Energy Efficient Ethernet disabled
Inter-network Connectivity
IGMPv3 required for SSM (Source-Specific Multicast)
Enable PIM (Protocol Independent Multicast) on Layer 3 devices for SSM
*PIM-SSM is recommended for interfaces connecting different subnets and uses the 232.0.0.0 to 232.255.255.255 range
Configure Access Control Lists and Firewalls to allow traffic from required address ranges/ports
1G Switch Decoder DisplayEncoder
HDMI CATx
Source
MODEL 80
FLAT PANEL
NAV SD 101
NAV
HDCP
VIDEO
CONFIG
NAV LNK
ACT
ANALOG
AUDIO
AUDIO LAN ID
NAV E 101
INPUTS
HDCP
HDMI
CONFIG
STREAM LNK
ACT
ANALOG
AUDIO
HDMI AUDIO
NAV LAN ID
© 2018 Extron Electronics. All rights reserved. All trademarks mentioned are the property of their respective owners. Prices and specications subject to change without notice.
NAV Pro AV Over IP Solutions
Minimum Network Requirements & Guidelines – 10G Infrastructures
The NAV
AV over IP platform uses standard 1G and 10G networks. Below are minimum requirements and
guidelines to ensure a successful implementation for a 10G system. For 1G system requirements, please see
the other side.
10G Switch Decoder DisplayEncoder
HDMI Fiber
Source
MODEL 80
FLAT PANEL
NAV 10SD 101
NAV
HDCP
VIDEO
CONFIG
ANALOG
HDMI
LNK
ACT
AUDIO
AUDIO LAN ID
NAV 10E 101
INPUTS
HDCP
HDMI
CONFIG
STREAM LNK
ACT
NAV
ANALOG
AUDIO
HDMI AUDIO
NAV LAN ID
Minimum Network Requirements – 10G Systems
Implementation Considerations
Devices can be installed on a physically isolated network or converged onto existing Gbps networks
For streaming on a private network use the 239.255.0.0 to 239.255.255.255 range which is reserved
for administratively scoped addressing
Singlemode or Multimode fiber optic cable for 10 Gbps speeds
Network Switch Hardware
10 Gbps port for every connected NAV 10G endpoint
IGMPv2 or IGMPv3 implemented
Layer 2+ or 3
Ensure switch supports non-blocking backplane/chassis
If applicable, use switches that support 802.1x for endpoint authentication
Network Switch Settings
IGMPv2 or IGMPv3 snooping enabled on all switches and VLANs
IGMPv2 or IGMPv3 querier enabled on one of the switches if no router is present
IGMP Immediate Leave/Fast Leave enabled
802.3az Energy Efficient Ethernet disabled
Inter-network Connectivity
IGMPv3 required for SSM (Source-Specific Multicast)
Enable PIM (Protocol Independent Multicast) on Layer 3 devices for SSM
*PIM-SSM is recommended for interfaces connecting different subnets and uses the 232.0.0.0 to 232.255.255.255 range
Configure Access Control Lists and Firewalls to allow traffic from required address ranges/ports
  • Page 1 1
  • Page 2 2

Extron NAV 10E 101 User guide

Category
Network switches
Type
User guide

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI