Honda 08B26-S9V-100 User manual

Brand: Honda

Model: 08B26-S9V-100

Category: Toys & accessories

Type: User manual

PARTS LIST

CD Changer Attachment Kit (sold separately):

P/N 08B26-S9V-100

Right base bracket

Left base bracket

Right changer bracket

Left changer bracket

BUS Cable

4 Flange bolts, 6 x 12 mm

4 Flange nuts

2 EPT seals (Black)

8 Wire ties

4 Washer-screws, 4 x 8 mm

2 Wire clips

CD Changer (sold separately):

P/N 08A26-1B1-100

CD changer

4 Washer-screws, 4 x 6 mm

(Not used)

Adhesive seal sheet

Locking covers

CD magazine

Owner’s Manual

Small wire tie

(Not used)

INSTALLATION

INSTRUCTIONS

Accessory Application Publications No.

Issue Date

MAY 2002

2003-2004 PILOT

CD CHANGER

ATTACHMENT

All 23607

2 Cushion tapes (Gray)

www.collegehillshonda.com/parts

With Navigation Unit:

• Remove the driver’s and passenger’s center

console trim pieces (three clips each). Take

care not to damage the clips.

TOOLS AND SUPPLIES REQUIRED

Flat-tip screwdriver

Phillips

screwdriver

Shop towel

Diagonal cutters

10 mm Combination wrenches

Isopropyl alcohol

Utility knife

INSTALLATION

Customer Information: The information in this

installation instruction is intended for use only by

skilled technicians who have the proper tools,

equipment, and training to correctly and safely add

equipment to your vehicle. These procedures

should not be attempted by “do-it-yourselfers.”

1. Make sure you have the anti-theft code for the

radio, then write down the frequencies for the

preset buttons.

2. Disconnect the negative cable from the battery.

3. Remove the audio unit.

Without Navigation Unit:

• Using a flat-tip screwdriver wrapped with a

shop towel, gently pry out on the audio panel

to remove the five clips. Unplug the connectors

and remove the audio panel.

• Remove the four screws that fasten the audio

brackets. Pull the audio unit out toward you,

unplug the vehicle connector and antenna lead

from the rear of the audio unit.

DRIVER’S CENTER

CONSOLE TRIM

PASSENGER’S

CENTER

CONSOLE TRIM

CLIPS (3)

AUDIO

UNIT

VEHICLE

CONNECTOR

ANTENNA

LEAD

AUDIO

BRACKET

AUDIO

BRACKET

SCREWS

(Reuse.)

AUDIO PANEL

CLIPS (5)

VEHICLE

CONNECTOR

4. On the driver’s side of the vehicle, gently pull the

center console lower cover out toward you to

release the seven clips and remove the center

console lower cover. Take care not to damage the

clips.

• Remove the four screws that fasten the audio

brackets. Pull the audio unit/heater control unit

out toward you, unplug the vehicle connectors

and antenna lead.

• Remove the center panel (four self-tapping

screws, two clips, and unplug the vehicle

accessory power outlet).

5. Remove the driver’s seat front cover by pulling it

toward you. Take care not to damage the clips.

CLIPS (2)

SELF-

TAPPING

SCREW

VEHICLE

CONNECTOR

CENTER

PANEL

HEATER

CONTROL

UNIT

AUDIO UNIT

AUDIO

BRACKET

SCREW

AUDIO

BRACKET

ANTENNA

LEAD

VEHICLE

CONNECTOR

CLIPS (7)

DRIVER’S CENTER

CONSOLE LOWER

COVER

DRIVER’S

SEAT

CLIPS (4)

DRIVER’S

SEAT FRONT

COVER

DRIVER’S

SEAT

With Navigation Unit:

• Route the BUS cable from the dashboard

opening to the driver’s floor. Pull out the end of

BUS cable 30 mm from the end of the vehicle

20-pin connector, and secure the BUS cable to

the vehicle harness with wire ties.

• Cut the EPT seal in half. Attach 1/2 of the EPT

seal on the edge of vehicle body to protect the

BUS cable. Before attaching the tape, wipe the

surface with isopropyl alcohol.

• Secure the BUS cable on the vehicle frame

with two wire ties.

Routing the BUS cable

6. Route the BUS cable.

Without Navigation Unit:

• Route the BUS cable from the dashboard

opening to the driver’s floor. Pull out the end of

BUS cable 30 mm from the end of the vehicle

20-pin connector, and secure the BUS cable to

the vehicle harness and frame with three wire

ties.

30 mm

BUS

CABLE

EPT SEAL

Clean with isopropyl

alcohol.

FRAME

WIRE TIE

BUS CABLE

14-PIN

CONNECTOR

VEHICLE

HARNESS 20-PIN

CONNECTOR

CENTER

PANEL

OPENING

WIRE

TIE

FRAME

BUS

CABLE

WIRE

TIE

30 mm

VEHICLE

HARNESS

WIRE TIE

VEHICLE

20-PIN

CONNECTOR

BUS CALBE

14-PIN

CONNECTOR

Installing the CD Changer

11. Carefully unpack the CD changer. Remove the

three shipping clips, and discard the shipping

cover. Install an adhesive seal (included with the

CD changer kit) over each of the three clips holes.

Save the shipping clips for your customer in the

event the unit needs to be serviced.

7. Using 1/2 of an EPT seal attach it to the frame at

the location shown. Measure 450 mm from the

end of the BUS cable to the frame, then bundle up

the excess cable and secure it to the vehicle with

three wire ties.

10. Install the right and left base brackets to the

driver’s seat raisers using two 6 x 12 mm flange

bolts for each bracket. Do not tighten the bolts yet.

9. Near the edge of the driver’s seat raiser make a

50 mm slit in the floor carpet with a utility knife.

Route the BUS cable under the floor carpet and

out the slit near the seat raiser.

8. Attach 1/2 of an EPT seal to the edge of the

frame in the area shown.

6 x 12 mm

FLANGE

BOLT

LEFT

BASE

BRACKET

RIGHT

BASE

BRACKET

SHIPPING CLIPS (3)

ADHESIVE SEALS (3)

SHIPPING COVER

(Discard.)

EPT SEAL

Cut in half.

WIRE

TIE

FRAME

450 mm

BUS CABLE

Bundle up

the excess

BUS cable.

Secure to the

vehicle harness.

1/2 EPT seal

(Clean with

isopropyl

alcohol.)

FLOOR

CARPET SLIT

BUS

CABLE

50 mm

Cut

here.

FRAME

15. Attach one cushion tape to the rear of the CD

changer leaving half of the cushion tape extended

past the CD changer. Using scissors, cut the

cushion at the end of the CD changer. Fold the

ends down and around the end of the CD

changer.

12. Visually check the position of the spring adjusting

pin on both sides of the CD changer. If the spring

adjusting pins are not in the horizontal (H)

position, move the pins to the horizontal (H)

position by sliding them up with your fingers.

13. Remove the adhesive backing from the “L” and “R”

locking covers, and attach them to the sides of

the CD changer. Align the diagonally opposite

holes with the H and V positions.

14. Install the right changer bracket to the CD

changer using two 4 x 8 mm washer-screws, and

the two wire clips. Install the left changer bracket

to the CD changer using two 4 x 8 mm washer-

screws.

SPRING

ADJUSTING

PINS

LEFT LOCKING

COVER

(Included with CD

Changer kit)

RIGHT

LOCKING

COVER

(Included with

CD Changer

kit)

SPRING

ADJUSTING PIN

(H: HORIZONTAL)

(V: VERTICAL)

WIRE

CLIP

RIGHT

CHANGER

BRACKET

LEFT

CHANGER

BRACKET

4 x 8 mm

WASHER-

SCREW

4 x 8 mm

WASHER-

SCREW

WIRE

CLIP

FRONT

16. Attach the cushion tape to the top of the left

changer bracket align the cushion tape already

attached. Fold the cushion tape around the CD

changer.

17. Insert the studs of the left and right base brackets

into the holes in the left and right changer

brackets, then install the four flange nuts on the

end of each stud. Tighten the four flange nuts and

four bracket bolts in step 10 on the bracket plates.

RIGHT BASE

BRACKET

LEFT BASE

BRACKET

FLANGE

NUTS (4)

RIGHT

CHANGER

BRACKET

CD CHANGER

LEFT CHANGER

BRACKET

CUSHION TAPE

CUSHION

TAPE

LEFT CHANGER

BRACKET

With CD/Cassette Tuner:

(With Navigation Unit)

With Cassette Player:

19. At the dashboard area, plug the BUS cable 14-pin

connector, the vehicle connectors, and the

antenna lead into the rear of the audio unit.

With Pocket:

18. Plug the BUS cable connector into the CD

changer connector. Bundle up any excess BUS

cable and attach it to the CD changer bracket with

the two wire clips installed in step 14.

BUS CABLE

14-PIN

CONNECTOR

AUDIO UNIT

CASSETTE

PLAYER

ANTENNA

LEAD

VEHICLE

20-PIN

CONNECTOR

BUS CABLE

14-PIN

CONNECTOR

AUDIO UNIT

ANTENNA

LEAD

VEHICLE

20-PIN

CONNECTOR

VEHICLE

16-PIN

CONNECTOR

VEHICLE

22-PIN

CONNECTOR

BUS CABLE

CD CHANGER

WIRE CLIP

BUS CABLE

14-PIN

CONNECTOR

AUDIO UNIT

POCKET

ANTENNA

LEAD

VEHICLE

20-PIN

CONNECTOR

21. Check that all wire harnesses are routed properly

and all connectors are plugged in.

22. Reinstall all removed parts.

23. Place shipping clips in a plastic bag and put the

bag in the glove box.

24. Reconnect the negative cable to the battery.

25. Enter the customer’s radio anti-theft code, and

reset the radio station presets.

NOTE: Whenever the battery is disconnected, the

driver’s window AUTO function is disabled.

26. Start the engine. Push down on the driver’s

window switch until the window is fully open.

27. Pull up on the driver’s window switch to close the

window completely, then hold the switch for two

seconds.

28. Test the AUTO window function.

29. Do the idle learn procedure.

 Make sure all electrical items are turned off.

 Start the engine. Hold the engine speed at 3,000

rpm with no load (in Park or Neutral) until the

radiator fan comes on.

 Let the engine idle for about 5 minutes with the

throttle fully closed and with all electrical items

off.

NOTE: If the radiator fan comes on during this step,

the time when it is operating must not be included in

the 5 minutes.

With Navigation Unit:

20. Slide the audio unit into the center panel opening,

and reinstall the four screws.

Without Navigation Unit:

AUDIO

UNIT

BUS CABLE

CONNECTOR

VEHICLE

CONNECTOR

ANTENNA

LEAD

SCREWS

(reused)

AUDIO

BRACKET

AUDIO UNIT

BUS

CABLE

VEHICLE

HARNESS

ANTENNA

LEAD

SCREW

(reused)

VEHICLE

HARNESS

HEATER

CONTROL

Honda 08B26-S9V-100 User manual

Brand: Honda

Model: 08B26-S9V-100

Category: Toys & accessories

Type: User manual

Download PDF

report

Honda 08B26-S9V-100 User manual

Honda 08B26-S9V-100 User manual

Related papers

Other documents