Infineon KIT_T2G-B-H_LITE Quick start guide

Infineon
Brand
Infineon
Model
KIT_T2G-B-H_LITE
Type
Quick start guide
-
QUICK START GUIDE
TRAVEOTM T2G Body High Lite Kit
KIT_T2G-B-H_LITE
Kit contents
1. KIT_T2G-B-H_LITE Board 2. Quick start guide (this document)
www.infineon.com/traveobhlitekit
Quick Start Guide Page 2 of 4
1USB cable connected to the
KitProg3 USB connector
2
Before you start
1. Ensure that you have the following:
– PC with USB port
– UART terminal soware such as Tera Term
or Minicom
2. Visit the kit webpage to download and install the
required soware.
Connect and power up the board
1. Connect the power adapter provided with the kit to the
board (J1).
2. Connect the KitProg3 USB connector (J2) to your PC.
Connect the kit with the UART terminal soware
1. Open the UART terminal soware and connect to the kit’s
USB-to-UART COM port with the following settings:
– Baud rate: 115200, Data: 8 bit, Parity: none as shown in
the UAB-UART COM port setup figure
– Stop bit: 1 bit, Flow control: none as shown in the
UAB-UART COM port setup figure
2. Press the RESET button (SW2) to reset the device.
Run the pre-programmed code example
1. Observe the “Hello World!!!” message on the serial
terminal and confirm that the three user LEDs blink one
aer the other.
2. Press the Enter key to pause or resume blinking the user
LED. Alternatively, use USER BTN1 or USER BTN2 to
pause or resume the blinking.
3. Follow the instructions on the serial terminal
to run other demos.
Run the pre-programmed code example
1. Observe the “Hello World!!!” message on the serial
terminal and confirm that the three user LEDs blink one
aer the other.
2. Press the Enter key to pause or resume blinking the user
LED. Alternatively, use USER BTN1 or USER BTN2 to
pause or resume the blinking.
3. Follow the instructions on the serial terminal
to run other demos.
Run the pre-programmed code example
1. Observe the “Hello World!!!” message on the serial
terminal and confirm that the three user LEDs blink one
aer the other.
2. Press the Enter key to pause or resume blinking the user
LED. Alternatively, use USER BTN1 or USER BTN2 to
pause or resume the blinking.
3. Follow the instructions on the serial terminal
to run other demos.
Next steps
Visit the kit webpage for information on code examples
supported for this kit and kit documentation.
Note:
The demos on the serial terminal may dier because of
continuous feature enhancements.
USB-to-UART COM port setup
3 Serial terminal
Quick Start Guide Page 3 of 4
TRAVEOTM T2G Body High Lite Kit Board details
1 Shield2Go connectors (not mounted) (J7, J19)
2 mikroBUS connectors (J11, J12)
3 32.768-kHz oscillator for WCO (Y1)
4 16-MHz oscillator for ECO (Y2)
5 Ethernet physical layer (PHY) transceiver (U11)
6 RJ45 Ethernet connector (J6)
7 TRAVEO™ T2G microcontroller (U6)
8 8-pin Arduino header (J13)
9 Expansion header 1 (X1)
10 6-pin Arduino header (J15)
11 DC power jack (J1)
12 Power LED (LED2)
13 KitProg3 USB Micro-B connector (J2)
14 VDD current measurement jumper (J20)
15 MIPI10/20 debug connector (J4)
16 KitProg3 status LED (LED1)
17 PSoC™ 5LP based KitProg3 (U4)
18 Mode switch (SW1)
19 T2G-B-E VDDIO current measurement jumper (J21)
20 8-pin Arduino header (J14)
21 Potentiometer (VR5)
22 USER LED (LED)
23 USER LED2 (LED4)
24 USER LED1 (LED3)
25 Expansion Header 1 (X2)
26 10-pin Arduino header (J16)
27 CAN FD transceiver (U8)
28 CAN FD connector (J5)
29 USER2 button (SW3)
30 USER1 button (SW2)
31 RESET button (SW1)
32 25-MHz crystal for Ethernet transceiver (Y3)
1
2
1
3
4 765 8 9 10
11
12
13
14
15
17
16
18
19
20
21
22
23242526272829
303132
Quick Start Guide Page 4 of 4
KIT_T2G-B-H_LITE Board pinout details
AN
RST
CS
SCK
MISO
MOSI
V
GND
PWM
INT
RX
TX
SCL
SDA
V
GND RX
TX
RST
GPIO
CS
CLK
MOSI
MISO
V
AN
AN
SDA
SCL
GND
V
INT
PWM
Date: 07 / 2023
All rights reserved. © 2023
Infineon Technologies AG
Document number: 002-37238 Rev. **
For additional details, see the kit guide available on the Infineon kit webpage.
RX
TX
RST
GPIO
CS
CLK
MOSI
MISO
UART_RX/D
UART_TX/D
P_/D
P_/D
P_/D
P_/D
P_/D
P_/D
VIN/VIN
GND_/GND
GND_/GND
V/V
V/V
RST/XRES_L_MCU
IOREF/V
P/NC
POT_AOUT/A
ADC_/A
ADC_/A
ADC_/A
ADC_/A
ADC_/A
V
P_
NC
NC
NC
NC
SPI_MOSI
SPI_CSO
SPI_CLK
SPI_MISO
NC
NC
NC
NC
XRES_L_MCU
ADC_
SPI_CS
P_
NC
GND
GND
P_
NC
NC
NC
NC
P_
P_
P_
P_
NC
NC
NC
NC
NC
NC
SPI_CS
SPI_CS
P_
VIN
V
AN
AN
SDA
SCL
GND
V
INT
PWM
V
NC
NC
NC
NC
NC
POT_AOUT
P_
ADC_
ADC_
NC
NC
V
P_
UART_TX
USER_SW
USER_LED
NC
NC
GND
GND
NC
NC
NC
NC
NC
NC
P_
P_
ADC_
ADC_
NC
NC
UART_RX
NC
USER_SW
USER_LED
USER_LED
NC
VIN
(AD/SCL)C_SCL
(AD/SDA)C_SDA
AREF/V
GND_/GND
D/SPI_CLK
D/SPI_MISO
D/SPI_MOSI
D/SPI_CS
D/P_
D/P_
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4

Infineon KIT_T2G-B-H_LITE Quick start guide

Infineon
Brand
Infineon
Model
KIT_T2G-B-H_LITE
Type
Quick start guide
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents