Sauder Shoal Creek 422194 Operating instructions

Need help? Visit Sauder.com to view video assembly tips or chat with a live rep.

Prefer the phone? Call 1-800-523-3987.

Share your journey!

sauder.com

Sit and surf.

NOTE: THIS INSTRUCTION

BOOKLET CONTAINS IMPORTANT

SAFETY INFORMATION.

PLEASE READ AND KEEP FOR

FUTURE REFERENCE.

English pg 1-35

Français pg 36-39

Español pg 40-44

Lot # 505895 07/05/17

Purchased: __________________

Be sure to give us a ring before

making any returns. 1-800-523-3987

Computer Desk

Shoal Creek Collection | Model 422194

Table of Contents Assembly Tools Required

Part Identiﬁ cation

Hardware Identiﬁ cation

Assembly Steps

Français

Español

Safety

Warranty

Hammer

Not actual size

No. 2 Phillips Screwdriver

Tip Shown Actual Size

Skip the power trip.

This time.

3

4-5

6-35

36-39

40-44

45-46

47

422194 www.sauder.com/servicesPage 2

Short Screwdriver

Part Identiﬁ cation

å While not all parts are labeled, some of the parts will have a label or an inked letter on the edge

to help distinguish similar parts from each other. Use this part identiﬁ cation to help identify similar parts.

Now you know

our ABCs.

A RIGHT END (1)

B LEFT END (1)

C UPRIGHT (1)

D

RIGHT FRONT/LEFT

REAR LEG (2)

D28 LARGE RIGHT DRAWER SIDE (1)

D29 LARGE LEFT DRAWER SIDE (1)

D78 LARGE DRAWER BACK (1)

D107 SMALL RIGHT DRAWER SIDE (1)

D108 SMALL LEFT DRAWER SIDE (1)

D109 SMALL DRAWER BACK (1)

D707 DRAWER BOTTOM (2)

E LEFT FRONT LEG (2)

F RIGHT REAR LEG (1)

G CENTER REAR LEG (1)

H UPPER UPRIGHT (1)

I LOWER UPRIGHT (1)

J ADJUSTABLE SHELF (1)

K END MOLDING (3)

L LARGE DRAWER FRONT (1)

M SMALL DRAWER FRONT (1)

N BOTTOM (1)

O SHELF (1)

P DOOR (1)

Q BACK (1)

R PURSE SHELF (1)

S MODESTY PANEL (1)

T TOP (1)

D28

D29

D78

D707

L

D107

D108

D109

M

A

B

C

E

F

G

D

H

I

J

K

T

N

O

P

Q

S

R

422194www.sauder.com/services

Page 3

Hardware Identiﬁ cation

å Screws are shown actual size. You may receive extra hardware with your unit.

HALF GROMMET - 2

67P

40CA

CABINET RIGHT - 1

40CB

CABINET LEFT - 1

40CC

DRAWER RIGHT - 1

40CD

DRAWER LEFT - 1

FILE GLIDE - 2

15B

EXTENSION SLIDE - 2

40MC

EXTENSION RAIL - 2

40MA

(EXTENSION SET SHOWN SEPARATED)

GROMMET CAP - 1

1P

CAM COVER - 18

12P

7F

TWIST-LOCK

®

FASTENER - 25

METAL PIN - 6

1R

29M

BUMPER CARD - 1

PULL - 2

7K

10A

SLIDE CAM - 4

22H

HINGE SPACER - 2

CAM SCREW - 22

8F

KNOB - 1

24K

WOOD DOWEL - 8

15F

GROMMET - 2

10P

HIDDEN CAM - 22

1F

RUBBER SLEEVE - 4

2R

14H

HINGE - 2

422194 www.sauder.com/servicesPage 4

Hardware Identiﬁ cation

å Screws are shown actual size. You may receive extra hardware with your unit.

BLACK 1-1/8" MACHINE SCREW - 1

21S

SILVER 3/4" MACHINE SCREW - 4

20S3S

GOLD 5/16" FLAT HEAD SCREW - 16

SILVER 5/8" FLAT HEAD SCREW - 4

23S

BLACK 9/16" FLAT HEAD SCREW - 6

32S

BLACK 1-15/16" FLAT HEAD SCREW - 10

113S

30S

BLACK 1-9/16" FLAT HEAD SCREW - 8

422194www.sauder.com/services

Page 5

Step 1

Look for this icon. It means a

video assembly tip is available at

www.sauder.com/services/tips

å

Assemble your unit on a carpeted ﬂ oor or on the empty

carton to avoid scratching your unit or the ﬂ oor.

å

To begin assembly, push a SAUDER TWIST-LOCK®

FASTENER (7F) into the large holes in the MODESTY

PANEL (S) and PURSE SHELF (R). Repeat this step for

the ENDS (A and B), UPRIGHT (C), LOWER UPRIGHT (I),

SHELF (O), and BACK (Q).

Do not tighten the TWIST-LOCK® FASTENERS in this step.

(25 used)

7F

R

S

422194 www.sauder.com/servicesPage 6

7F

Step 2

Arrow

The arrow in the HIDDEN

CAM must point toward the

hole in the edge of the board.

Hole

å

Push twenty-two HIDDEN CAMS (1F) into the ENDS (A and B),

UPRIGHT (C), and BACK (Q).

1F

Arrow

A

B

Q

C

Arrow

1F

(22 used)

422194www.sauder.com/services

Page 7

Step 3

D

E

F

G

8F

å

Turn twenty-two CAM SCREWS (8F) into

the LEGS (D, E, F, and G).

8F

(22 used)

422194 www.sauder.com/servicesPage 8

Remember:

Righty tighty.

Lefty loosey.

Step 4

B

å

Turn two BLACK 9/16" FLAT HEAD SCREWS (32S) into

the LEFT END (B) until the shoulders of the SCREWS rest

on the surfaces of the END.

å

NOTE: Do not overtighten the SCREWS.

å

Slide the END MOLDING (K) onto the LEFT END (B). Line

up the grooves in the MOLDINGS over the heads of the

SCREWS in the END .

å

NOTE: The MOLDING should be even on both edges of

the ENDS

å

NOTE: If the MOLDING comes up o of the SCREWS,

remove it and slide it on again.

BLACK 9/16" FLAT HEAD SCREW

(2 used in this step)

32S

Shoulder

Apply pressure with your hands

as you guide the MOLDINGS over

the SCREWS and onto the ENDS.

Surface without TWIST-LOCK® FASTENERS

422194www.sauder.com/services

Page 9

K

Step 5

B

D

E

These surfaces

should be even.

15F

Angled edge

Edge with

TWIST-LOCK®

FASTENERS

Surface with HIDDEN CAMS

å

Insert two WOOD DOWELS (15F) into the LEGS (D and E).

å

Fasten the LEFT END (B) to the LEGS (D and E). Tighten

six HIDDEN CAMS.

å

NOTE: Be sure the WOOD DOWELS insert into the END.

1

2

422194 www.sauder.com/servicesPage 10

å

Insert two WOOD DOWELS (15F) into the LEGS (F and G).

å

Fasten the BACK (Q) to the LEGS (F and G). Tighten six

HIDDEN CAMS.

å

NOTE: Be sure the WOOD DOWELS insert into the BACK.

Step 6

F

Q

G

These surfaces

should be even.

15F

Angled edge

Edge with

TWIST-LOCK®

FASTENERS

Surface with HIDDEN CAMS

1

2

422194www.sauder.com/services

Page 11

Step 7

E

C

A

D

å

Insert a WOOD DOWEL (15F) into each of the LEGS (D and E).

å

Fasten the UPRIGHT (C) to a LEFT FRONT LEG (E) as

shown to the right. Tighten three HIDDEN CAMS.

å

Fasten the RIGHT END (A) to a RIGHT FRONT/LEFT

REAR LEG (D) as shown below. Tighten three HIDDEN CAMS.

å

NOTE: Be sure the WOOD DOWEL inserts into the END

and UPRIGHT.

15F

These surfaces

should be even.

These surfaces

should be even.

Edge with

TWIST-LOCK®

FASTENERS

Edge with

TWIST-LOCK®

FASTENERS

Surface with HIDDEN CAMS

Angled edge

1

2

422194 www.sauder.com/servicesPage 12

Step 8

D

A

I

å

Separate the EXTENSION SLIDES (40MC) from the EXTENSION RAILS (40MA) as

shown in the upper diagram below. Be prepared, the parts are greasy.

å

Fasten the EXTENSION RAILS (40MA) to the RIGHT END (A) and LOWER

UPRIGHT (I). Use four GOLD 5/16" FLAT HEAD SCREWS (3S).

å

NOTE: For each EXTENSION RAIL, turn a SCREW into the hole shown in the

enlarged diagram. Then, slide the inner cartridge of the EXTENSION RAIL in to ﬁ nd

the other hole that lines up with the hole in the END. Turn a SCREW into this hole.

å

NOTE: The EXTENSION SLIDES will be used later for the LARGE DRAWER SIDES.

GOLD 5/16" FLAT HEAD SCREW

(4 used in this step)

3S

Push the black lever in and pull the SLIDE from the RAIL.

Open end

40MA40MC

422194www.sauder.com/services

Page 13

Step 9

A

I

å

Fasten the CABINET RIGHT (40CA) to the RIGHT END (A)

and the CABINET LEFT (40CB) to the LOWER UPRIGHT (I).

Use four GOLD 5/16" FLAT HEAD SCREWS (3S) through

holes #1 and #3.

GOLD 5/16" FLAT HEAD SCREW

(4 used in this step)

3S

1

2

3

4

1

2

3

4

Roller end

422194 www.sauder.com/servicesPage 14

å

Fasten the RIGHT END (A) and UPRIGHT (C) to the

SHELF (O). Tighten four TWIST-LOCK® FASTENERS.

Step 10

A

O

C

Dowel end

How to use the SAUDER TWIST-LOCK® FASTENER

1. Insert the dowel end of the FASTENER into the

hole of the adjoining part.

NOTE: The dowel end of the FASTENER must

remain fully inserted in the hole of the adjoining

part while locking the FASTENER.

2. Tighten the FASTENER with a Phillips

screwdriver as tight as possible.

Surface with TWIST-LOCK® FASTENERS

Unﬁ nished edge

422194www.sauder.com/services

Page 15

Surface without HIDDEN CAMS

Surface with HIDDEN CAMS

å

Fasten the UPPER UPRIGHT (H) to the SHELF (O). Use

two BLACK 1-15/16" FLAT HEAD SCREWS (113S).

Step 11

O

H

BLACK 1-15/16" FLAT HEAD SCREW

(2 used in this step)

113S

Edge with small holes

422194 www.sauder.com/servicesPage 16

å

Fasten the LOWER UPRIGHT (I) to the SHELF (O). Tighten

two TWIST-LOCK® FASTENERS.

Step 12

O

I

Surface with

TWIST-LOCK®

FASTENERS

Roller end

422194www.sauder.com/services

Page 17

å

Fasten the BOTTOM (N) to the LOWER UPRIGHT (I),

RIGHT END (A) and UPRIGHT (C). Use six BLACK 1-15/16"

FLAT HEAD SCREWS (113S).

Step 13

N

A

C

BLACK 1-15/16" FLAT HEAD SCREW

(6 used in this step)

113S

I

422194 www.sauder.com/servicesPage 18

Step 14

A

C

å

Turn four BLACK 9/16" FLAT HEAD SCREWS (32S) into the RIGHT END (A) and UPRIGHT (C) until the shoulders of the

SCREWS rest on the surfaces of the END.

å

NOTE: Do not overtighten the SCREWS.

å

Slide the RIGHT END MOLDINGS (K) onto the RIGHT END (A) and UPRIGHT (C). Line up the grooves in the MOLDINGS over

the heads of the SCREWS in the END and UPRIGHT.

å

NOTE: The MOLDINGS should be even with the top edges of the END and UPRIGHT.

å

NOTE: If the MOLDING comes up o of the SCREWS, remove it and slide it on again.

BLACK 9/16" FLAT HEAD SCREW

(4 used in this step)

32S

BLACK 9/16" FLAT HEAD SCREW

32S

Apply pressure toward the END with

your hands as you guide the MOLDING

over the SCREWS and onto the END.

Apply pressure toward

the UPRIGHT with

your hands as you

guide the MOLDINGS

over the SCREWS and

onto the UPRIGHT.

Shoulder

The groove should be against

the END and UPRIGHT.

Shoulder

K

422194www.sauder.com/services

Page 19

å

Insert two WOOD DOWELS (15F) into the LEGS (F and G).

å

Fasten the RIGHT END (A), and UPRIGHT (C) to the

LEGS (F and G). Tighten six HIDDEN CAMS.

å

Fasten the LOWER UPRIGHT (I) to the BACK (Q). Tighten

two TWIST-LOCK® FASTENERS.

å

NOTE: Be sure the WOOD DOWELS

insert into the END and UPRIGHT.

Step 15

N

A

C

F

Q

G

15F

1

2

I

422194 www.sauder.com/servicesPage 20

Page is loading ...

Sauder Shoal Creek 422194 Operating instructions

Sauder Shoal Creek 422194 Operating instructions

in other languages

Related papers

Other documents