ACTi R21CF-3x Installation guide

Face Recognition Reader

Installation Guide

R21CF-30, R21CF-31, R21CF-32, R21CF-33

2018/01/19

www.acti.com

Installation Guide

2

The following documentation covers the installation / configuration procedures of your device.

NOTE: The accuracy of the analytics algorithm may be affected by different environmental

factors or inappropriate installation. Please follow the procedures in this installation guide.

ACTi will not be held liable for inaccuracies resulting from the aforesaid causes.

Step 1: Prepare for Installation

A. Bundled accessories

1. Mounting bracket

2. Screw pack

3. Input / Output cables

B. Additional requirements

1. DC 12 V Power supply with at least 1.5A output

2. Ethernet cable

Step 2: Know the Device

The Device

www.acti.com

Installation Guide

3

Port Pins

Port

Pin#

Definition & Color

P1

(Power)

1

12V POWER SUPPLY

2

12V POWER GND

P2

(Digital I/O)

1

Brown

12V DC OUT

2

Black

12V DC OUT

3

Pink

DOOR SENSOR INPUT

4

Purple

EXIT SWITCH INPUT

5

White

RELAY 1 COM

6

Gray

RELAY 2 COM

7

Green

RELAY 1 NC

8

Yellow

RELAY 2 NC

9

Blue

RELAY 1 NO

10

Orange

RELAY 2 NO

P3 (Communication)

1

Red

12V Power OUT

2

Black

12V Power OUT GND

3

Blue

Wiegand IN Data 0

4

Gray

Wiegand IN Data 1

5

Green

Wiegand OUT Data 0

6

White

Wiegand OUT Data 1

7

Orange

RS232 Tx

8

Yellow

RS232 Rx

P4

(Network)

Standard Gigabit Ethernet

DC 12V Power, 2Amp

Right: 12V DC

Left: Ground

www.acti.com

Installation Guide

4

Typical Wiring Scheme

Step 3: Connect Other Devices

1. Route the cables through the hole on the wall.

2. Connect the devices, such as the power adapter, to the cables with terminal block (refer

to the earlier sections to check the proper wiring connections).

www.acti.com

Installation Guide

5

Step 4: Install the Device

Installation Height Consideration

 For installation with multiple devices, all units (including unit used for user enrollment)

must be installed at the same height

 Installation height depends on the end user’s minimum and average height

 See below table to find the appropriate installation height

Installation

Height of Device (H)

Minimum

User Height

Maximum

User Height

1.05 m

1.30 m

1.70 m

1.10 m

1.35 m

1.75 m

1.15 m

1.40 m

1.80 m

1.20 m

1.45 m

1.85 m

1.25 m

1.50 m

1.90 m

1.30 m

1.55 m

1.95 m

Installation height (H) measured from

the bottom of the device to ground

www.acti.com

Installation Guide

6

Installation Procedures

Decide the appropriate

height to mount the

device (refer to the table

above).

Ensure power, network,

communication, and I/O cables

are available from the opening

of the mounting bracket.

Ensure the device is

vertically installed and

parallel to a vertical wall.

Apply screws to tighten

the mounting bracket on

the wall.

www.acti.com

Installation Guide

7

Finally, mount the two (2)

bundled screws at the

bottom of the device.

Power up the device to test if all

the cables are connected

correctly

Connect all the cables to the

ports, and mount the device

gently.

Hook the top of the bracket and

press it down. Slide the unit

down to reach the bottom of the

bracket.

7F, No. 1, Alley 20, Lane 407, Sec. 2, Ti-Ding Blvd., Neihu District, Taipei, Taiwan 114, R.O.C.

TEL : +886-2-2656-2588 FAX : +886-2-2656-2599

Email: [email protected]om

ACTi R21CF-3x Installation guide

ACTi R21CF-3x Installation guide

Related papers