2. PortaPivot
  3. V2
V2

PortaPivot V2 User guide

  • Hello! I am an AI chatbot trained to assist you with the PortaPivot V2 User guide. I’ve already reviewed the document and can help you find the information you need or explain it in simple terms. Just ask your questions, and providing more details will help me assist you more effectively!
8 x Maxxfast
CST 4.5x50
8 x DIN ≈965 A
M5x10
www.portapivot.com
4 x SP-CRL
2 x SP-PHD (=XL)
1 x TORX BIT TX 25
1 x TORX BIT TX 20
16 x DIN 988-5x10x1
4 x DIN916-M6x6
4 x Fisher
Duopower 8x40
4 x Maxxfast
CK 6x50
4 x PAP-ADKPB 2 x SP-PZOV 3 mm
2 x SP-PZOV 1.5 mm
2 x SP-PZOV 1.5 mm
2 x SP-PZOV 1 mm
2 x SP-PZOV 1 mm
OPTIONAL STEALTHPIVOT XL ACCESSORY SET
OPTIONAL STEALTHPIVOT INSTALLATION TOOL
STEALTHPIVOT XL SET
2 x PAP-1W 8 x Maxxfast CST 4.5x50
4 x Fisher Duopower 8x40
1 x SP-PS&KAL
4 x PAP-2W
4 x magnet South/North
4 x ISO 10642 - M4x8
OPTIONAL STEALTHPIVOT INSTALLATION TOOL
STEALTHPIVOT XL - QUICKSTART GUIDE
By PortaPivot
33
25.25
18
11.25
Ø3
25.75
35
5
236.5
270.5
25.75
33
99
225
270
R5
R5.25
7.25
256
STEALTHPIVOT XL CAVITY DIMENSIONS (mm)
STEALTHPIVOT XL DIMENSIONS (mm)
1000
500
250
85
joint A & BX
Th
2
2
3
4
40
2
2
3
3
30
2
3
3
5
50
3
3
4
7
60
Door WIDTH
Xmin = W-1150
Xmin ≥ 150
*Xmin result
1100
-50
no
150
Door WIDTH
Xmin = 1/3
1751
584
1800
600
2100
700
EXAMPLES EXAMPLES
1200
50
no
150
1350
200
yes
200
1500
350
yes
350
11 mm
3 mm* 3 mm*
11 mm
joint A joint B
Pivot distance = X
Door thickness = Th
Xmax = 1/2Xmax = 1/2
Xmin = 1/3
WIDTH = 1000-1750 WIDTH = 1751-2250
Xmin = WIDTH-1150
Xmin ≥ 150*
AXIS POSITIONSAXIS POSITIONS (X)
ADVISED JOINT DIMENSIONS
Max. width = 2250 mm
Max. weight = 150 kg (330 lbs)
Top & bottom joints: min. 11 mm
*Left & right joints:
The minimum joint depends on the
door thickness and pivot distance.
For visual coherence, we advise to
use equal joints left and right. See
visual and table below for advised
left and right joint dimensions.
180°
360°
S90 should always be
oriented the same for top
and bottom hinge!
S90 - 90° STOP ACCESSORY
75 mm
AXIS*
75 mm
Ø 8 mm
45 mm deep
1
3
2
DRILL PIVOT MOUNT HOLES
*Depends on doorway measurements!
SYNCHRONIZE PIVOT AXIS HEIGHT IN DOORWAY
difference
difference
Height between floor and
ceiling at pivot axis
Pivot to pivot
distance on door
DOORWAY DOOR
MAXIMUM
RECTANGLE
Compare the measured doorway height at the pivot axis with the
pivot to pivot distance of the door. Synchronize them if necessary by
using one of the hinge height adjustment options on the next page.
INSTALL IN SOLID OR REINFORCED MATERIALS!
HINGE HEIGHT ADJUSTMENT OPTIONS
For TOP or BOTTOM joint adjustment
= preferred method for bottom hinge
1. Shims between hinge and door
For TOP or BOTTOM joint adjustment
= faster but less stable method
2. Shims between hinge and floor
Only for TOP joint adjustment and non compressible door structures!
3. Inbus screws
1
3
2
Use the drill tool to rotate the pivot mount in place.
Repeat for the bottom pivot mount.
Install the octagonal inserts at ‘position 1’ in the top mount, then insert
screws but do not fully tighten yet. Repeat for the bottom mount.
Always rotate the pivot mount
in the closing direction of the
door! If not, the door will be
blocked in its opened position.
INSTALL ASSEMBLED DOOR
Place the assembled door in the
doorway, with the pivot axis in
between the 2 pivot mounting holes.
Tilt the door upright
and keep it in place.
Put both pivots in their ‘closed’ position.
1
3
2
4
5
1,35 mm
1,50 mm
1,20 mm
1,05 mm
The inserts are excentric, so each position will affect the
centerline angle of the door leaf.
The view below shows the effect on the centerline angle
when rotating the inserts to different positions.
ADJUST PIVOT AXIS POSITION
0° POSITIONING ADJUSTMENTS
Optional
MINIMIZE VISIBLE COMPONENTS
INTERCHANGEABLE GAS DAMPERS
Slide the 3D printed covers over the base of the
hinge to cover up the screws and hexagonal inserts.
Stealthpivot NL and XL are equipped with 480N gas dampers which
can easily be replaced.
Optional 750N dampers are also available.
0°
+90°
-90°
0°
+90°
50
11
11 11
Ø8
neodymium
magnet
2-way
magnet holder
neodymium
magnet
1-way
magnet holder
69
55
optional shim for height adjustment
2-way magnet holder
1-way magnet holder
0° positioning magnet
(North/south)
2-way magnet holder
0° positioning magnet
(North/south)
OPTIONAL 0° POSITIONING ACCESSORIES
Ø8 mm
Maxxfast CST 4.5x50
Fischer duopower 8x40
www.portapivot.com
1-WAY2-WAY
1-WAY
magnet holders
2-WAY
magnet holders
2-WAY SETUP 1-WAY SETUP
Find more pictures, information and in-depth manuals
@
WWW.PORTAPIVOT.COM
By PortaPivot
/