SICK UP30-211118 Operating instructions

SICK
Brand
SICK
Model
UP30-211118
Category
Measuring, testing & control
Type
Operating instructions
Page is loading ...
We reserve the right to make changes without
prior notication
UP30-211118
8013214
ENGLISH
Ultrasonic sensor
with analogue- and switching output
Operating Instructions
Safety Specications
‡ No safety component in accordance with EU machine
guidelines.
‡ Read the operating instructions before starting operation.
‡ Connection, assembly, and settings only by competent
technicians.
‡ Protect the device against moisture and soiling when
operating.
Proper Use
The UP30-211118 is an ultrasonic sensor and is used for
non-contact level detection of uids.
Starting Operation
See ow chart C.
Maintenance
SICK sensors do not require any maintenance. We recom-
mend that you clean the external lens surfaces and check
the screw connections and plug-in connections at regular
intervals.
C
Flow chart
A
UP30-211118
Numerical parameterization by
LED display
Activate/deactivate display
touch control
Restore default settings
Add-on-Menü: Additional functions
switch off the
supply voltage
switch on the supply
voltage keeping T1
pressed down until »on«
or »off« appears
»on« or
»off«
»on« or
»off«
press T1 to activate
or deactivate
do not press any key
for 20 s
normal operation
switch off the supply
voltage
switch on the supply
voltage keeping T1
pressed down approx.
15 s until »rESEt«
has passed through
normal operation
2 T + 1 T
1 T
2 T
2 T + 1 T
keep T1 and T2 pressed down approx. 13 s until the welcoming
text has passed through and »Add« appears in the LED display
2 T + 1 T
2 T
1 T
2 T
1 T
2 T + 1 T
finished
» «: display
mm or cm
» «: display
%, 100%
corresponds
to smallest
analogue
value
» «: display
%, 100%
corresponds
to largest
analogue
value
»C01«: bright display
»C02«: display dimmed
»C03«: display off
The highest assigned
sensor address can
be entered optionally
for optimizing multi-
plex speed.
setting range »01«
to »10«
»F00«: no filter
»F01«: standard filter
»F02«: average value
filter
»F03«: foreground-
filter
»F04«: background-
filter
strength of the selec-
ted measurement
value filter
»P00«: weak filter
effect
to
»P09«: strong filter
effect
Influences the size of
the detection range.
»E01«: high
»E02«: standard
»E03«: low
smallest value:
blind zone
largest value:
window border near
the sensor – 1
power-save mode display mode select current/
voltage output
measurement
value filter
filter strengthforeground
suppression
multiplex operation
device address
multiplex operation
highest address
»Aut«: automatic
detection of
the load
»U«: voltage output
»I«: current output
»00«: synchronization
»01« to »10«:
sensor address
for multiplex
operation
»oFF«: synchronization
deactivated
smallest value:
sensor-remote
window border
largest value:
999 mm at
UM30-211118 and
UM30-212118
999 cm at
UM30-213118,
UM30-214118 and
UM30-215118
measurement range calibration display detection range
sensitivity
Level reflector, at
least 200 x 200 mm
2
large, aligned at a
right angle to the sen-
sor, position exactly at
a distance of 250 mm
from the sensor with
UM30-211113 and
UM30-212113 and
at exactly a distance
of 900 mm with all
other sensors. Set
250 mm or 900 mm
on the display. Con-
firm calibration by
pressing T1 + T2.
2 T + 1 T
1 T
2 T
2 T + 1 T
2 T
1 T
2 T + 1 T
1 T
2 T
2 T + 1 T
2 T
1 T
2 T + 1 T
1 T
2 T
2 T + 1 T
2 T
1 T
2 T + 1 T
1 T
2
T
2 T + 1 T
2 T
1 T
2 T + 1 T
1 T
2 T
2 T + 1 T
2 T
1 T
2 T + 1 T
1 T
2 T
2 T + 1 T
2 T
1 T
2 T + 1
T
1 T
2 T
2 T + 1 T
2 T
1 T
2 T + 1 T
1 T
2 T
2 T + 1 T
2 T
1 T
2 T + 1 T
1 T
2 T
2 T + 1 T
2 T
1 T
2 T + 1 T
1 T
2 T
2 T + 1 T
2 T
1 T
delay time in seconds
at approach of an
object between de-
tection of the object
and output of the dis-
tance value (acts like
a switch-on delay)
»00«: 0 s (no delay)
to
»20«: 20 s response
delay
response delay
2 T + 1 T
1 T
2 T
2 T + 1 T
2 T
1
T
Note:
Changes to the settings
in the add-on menu can
hamper the sensor function.
A6, A7, A8, A10, A11, A12
affect the extent of the re-
sponse delay of the sensor.
hysteresis
switching output
smallest value:
»001«
largest value:
difference between
limiting scanning
range and switching
point –1
Hysteresis affects
both switching points
in window operation.
2 T + 1 T
1 T
2 T
2 T + 1 T
2 T
1 T
keep T1 and T2 pressed down approx. 3 s
until the welcoming text has passed through
set the switching
point in mm or cm
for a simple
switching point,
press T2 until
»- - -« appears
set the sensor-
remote switching
point in mm or cm for
window operation
2 T
1 T
2 T
2 T
1
T
2 T + 1 T
1 T
2 T
2 T + 1 T
2 T + 1 T
2 T
1 T
2 T + 1 T
2 T + 1 T
2 T + 1 T
2 T
1 T
2 T
1 T
2 T
1 T
2 T + 1 T
set the window border near
the sensor in mm or cm
select the rising ( ) / falling
( ) output characteristic
1 T
2 T
2 T + 1 T
2 T
1 T
2 T + 1 T
2 T + 1 T
set the switching output
set the analogue output
set the sensor-remote
window border in mm or cm
finished
1
1
2
select the normally closed ( ) /
normally open ( ) contact
Parameterization of Teach-in
B
T1 D1 D2 T2
1
L+
Q
A
2
4
5
Q
PNP
brn
wht
blk
3
Sync/Com
gra
blu
M
Operating scanning dist. 30-500mm (700mm)
(limiting scanning dist.)
Ultrasound frequency 320kHz
Resolution 0,18 mm
Reproducibility ±0,15 % of limiting scanning
distance
Accuracy ≤ 2 % of limiting scanning
distance
Supply voltage
1)
9...30 V DC
Ripple ±10 %
Current consumption
2)
≤ 80 mA
Standby delay < 300 ms
Response time
3)
110 ms
Analogue output
4) 5)
4-20 mA/0-10 V
Connection type M 12, 5-pin
Process connection G 1/2
Pressure resistance/ area of use 0,5 - 6 bar gauge pressure
Enclosure rating IP 67
Ambient operating temperature
6)
-25...+70 °C
1)
Reverse-polarity protected
2)
Without load
3)
Recovery time 32 ms …180 ms according to EMC EN 50319
4)
Short-circuit protected, reversible
5)
Automatic switching between voltage and current outputs dependet on load 4 … 20 mA:
RL ≤ 100/at 9 V ≤ UB ≤ 20 V; RL ≤ 500/at UB ≥ 20 V; 0 … 10 V: RL ≥ 100 k/at UB ≥ 15 V,
short-circuit protected
6)
Temperature compensation at –25 …+50 °C, can be switched off
UP30-211118
Australia
Phone +61 3 9497 4100
1800 33 48 02 – tollfree
E-Mail [email protected]
Belgium/Luxembourg
Phone +32 (0)2 466 55 66
E-Mail [email protected]
Brasil
Phone +55 11 3215-4900
E-Mail [email protected]
Ceská Republika
Phone +420 2 57 91 18 50
E-Mail [email protected]
China
Phone +852-2763 6966
E-Mail [email protected]
Danmark
Phone +45 45 82 64 00
E-Mail [email protected]
Deutschland
Phone +49 211 5301-250
E-Mail [email protected]
España
Phone +34 93 480 31 00
E-Mail [email protected]
France
Phone +33 1 64 62 35 00
E-Mail [email protected]
Great Britain
Phone +44 (0)1727 831121
E-Mail [email protected]
India
Phone +91–22–4033 8333
E-Mail [email protected]
Israel
Phone +972-4-999-0590
E-Mail [email protected]
Italia
Phone +39 02 27 43 41
E-Mail [email protected]
Japan
Phone +81 (0)3 3358 1341
E-Mail [email protected]
Nederlands
Phone +31 (0)30 229 25 44
E-Mail [email protected]
Norge
Phone +47 67 81 50 00
E-Mail [email protected]
Österreich
Phone +43 (0)22 36 62 28 8-0
E-Mail [email protected]
Polska
Phone +48 22 837 40 50
E-Mail [email protected]
Republic of Korea
Phone +82-2 786 6321/4
E-Mail kang@sickkorea.net
Republika Slowenija
Phone +386 (0)1-47 69 990
E-Mail [email protected]
România
Phone +40 356 171 120
E-Mail [email protected]
Russia
Phone +7 495 775 05 34
E-Mail info@sick-automation.ru
Schweiz
Phone +41 41 619 29 39
E-Mail [email protected]
Singapore
Phone +65 6744 3732
E-Mail [email protected]
Suomi
Phone +358-9-25 15 800
E-Mail [email protected]
Sverige
Phone +46 10 110 10 00
E-Mail [email protected]
Taiwan
Phone +886 2 2375-6288
E-Mail [email protected]
Türkiye
Phone +90 216 587 74 00
E-Mail [email protected]
USA/Canada/México
Phone +1(952) 941-6780
1 800-325-7425 – tollfree
E-Mail [email protected]
UP30-211118
Standard factory settings of
UP30 are:
■ Rising analog characteristic
■ Window function for the
analog output set to blind
zone and operating range
■ Switching signal is set as
normally open
■ Switching signal set on ma-
ximum operating range
■ Measurement range set to
maximum range
  • Page 1 1
  • Page 2 2

SICK UP30-211118 Operating instructions

SICK
Brand
SICK
Model
UP30-211118
Category
Measuring, testing & control
Type
Operating instructions
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

in other languages

Related papers

Other documents