Optimus XEMEDV4BSCREEN User manual

Brand: Optimus

Model: XEMEDV4BSCREEN

Category: Door intercom systems

Type: User manual

XE MED V4B SCREEN MASTER STATION

Range: INTERCOM OVER IP

Series:

Installation  Connection  Programming  Use

Technical data sheet no. EN-604-0102A

www.castel.fr

Page 1 / 7

PRESENTATION

Product references: 540.4600 (XE MED V4B SCREEN)

The XELLIP washable master station with easy clean surface is part of a

complete, powerful Full IP multimedia system.

With native SIP, it includes the following functions (according to the

version):

 Set up Audio/Video over IP communication

 Recording on SIP server (option of configuring up to two backup

servers)

 Managing 1 to 4 programmable function buttons

 Manages a 4.3” TFT screen to display the video of the station in

communication

 Managing an "on-off" input

 Managing a single-pole dry contact to control a keeper or other organ

 Complies with the "Disability accessibility law": workstations equipped

with pictograms, colored LEDs, voice synthesizers, an integrated

magnetic induction loop

 Managing automatisms developed on the interfaces (time and logic

relations)

 Manage advanced automatisms (logical and hourly relations) on its

interfaces

 Run self tests automatically or on demand

 Update by TFTP (Trivial File Transfer Protocol).

 Integrate SNMP protocol (Simple Network Management Protocol)

 Integrate VLANs

 Secure the Ethernet network by using the 802.1X protocol (Radius)

 Backup on power failure.

 The PoE (Power over Ethernet) function

 Thanks to its embedded web server, it can be configured, monitored

and operated from any browser

VERSIONS

 The standard version of the washable master station can be powered by POE (Power over

Ethernet)

XE MED V4B SCREEN MASTER STATION

Technical data sheet no. EN-604-0102A

www.castel.fr

Page 2 / 7

CONNECTION

15-30VDC Power supply

RJ45: ETHERNET & 10/100 POE

USB (NC)

Logic input

Relay output

Reset Button

Amplifier connection

or magnétic induction loop

R T E C

Power supply connection

The station requires a power supply of 15 V to 30 V.

Comment: the station can be powered by the PoE network

Connection to the IP network

The connection is carried out by a 10/100 Mbit RJ45 Ethernet link.

Connection of the relay output

The connection is carried out via a 3-point terminal block providing a "make-and-break contact" interface (TRC).

If you use one of these relay outputs to control an AC or DC door release, wire a non-polarised 58 V diode in

parallel on the dry contact between C and T or between C and R according to the intended use (diode included).

Input connection

An on-off input allows the connection of a dry contact (do not supply power). In order to be activated, the input

must be earthed.

The contact can be up to 1 km away.

the door entry station by using the terminal supplied (mounted on microphone mount).

Protection against electrostatic discharges

IMPERATIVE : Connect the device to the ground using the terminal provided (Mounted on the fixing of the

microphone).

Debug

XE MED V4B SCREEN MASTER STATION

Technical data sheet no. EN-604-0102A

www.castel.fr

Page 3 / 7

INSTALLATION

Flush mounting:

 - Make a recess in the support with the following minimum dimensions: height 265 mm, width 167 mm and depth

48 mm.

 To guarantee a perfect seal for your station, it is necessary that the front face once mounted press on the whole

of the seal

USE

IP address of the station

Every station must have its own IP address in the network. This address can be provided by the network server

(DHCP addressing) or configured manually. The address can be configured from a PC using the web server of the

station

The station is delivered by default with a DHCP address. If no DHCP server is present, then the

station will take a fixed IP address of domain IP4All: 169.254.xx.xx. The IP address of station will be

found by the application CastelIPSearch or CASTELServeur. In the case where the discovery of the

IP address of the set is not possible, pressing the "reset" button of the station during operation

sets its IP address in 192.168.49.251.

Accessing the web server of the station

You can use any web browser, such as Firefox or Internet Explorer, to connect to the web server of the station. To do

so, open your internet browser on any PC connected to the network and enter: "https://" followed by the IP address of

the station ([https://ip_address_of_the_station]). You will then be connected directly to the web page for the station.

Now you simply need to enter your username (default: admin) and password (default: admin) to access the functions

of the web server.

The web server provides information on the station and allows you to configure

it.

In order to access all the functions, go to View / Full view.

On-line help, which can be accessed from any menu, provides information on

the various functions of the web server.

XE MED V4B SCREEN MASTER STATION

Technical data sheet no. EN-604-0102A

www.castel.fr

Page 4 / 7

FUNCTIONS

The washable master station is designed to dialogue, via the IP network, with other XELLIP stations, softphones, SIP phones or

any other elements that are compatible with the SIP standard.

General functions of the washable master station

 Configuring a network connection

 Setting up a SIP account

 Managing audio communication

↘ Setting the level of priority of the station

↘ Setting a call and communication time-out

↘ Automatic pick-up with and without delay

↘ Enabling secret mode for automatic pick-up

 Configure the viewer to customize the greeting or sleep timer

 Configure the keyboard to indicate the delay before the automatic lock

Functions of the audio interface

 Setting the speaker volume and the microphone volume

 Setting the voice transmission mode (Full Duplex / Half Duplex)

 Setting a noise-reduction level

 Configuring the RTP port number

 Validating / invalidating audio codecs

 Set up ring tones and tones

 Configure DTMF commands to control for example the local relay

 Configure noise detection

 Switch to simplex via a DTMF command:

↘ '*' to switch to simplex listening

↘ '#' to switch to speech simplex

↘ '0' returns to standard operation

Video interface functions

 Configure the RTP port number

 Validate/Cancel video codec

 Configure the bandwidth

Programmable button functions

All the buttons are programmable and can be used for:

 Making a call to 1 to 10 stations, simultaneously or with a time-delay

 Controlling the local relay, the relay of the station making or receiving the communication

 Sending a DTMF code

 Activating forwarding to a station

 Activating a call transfer

 Activating "do not disturb" mode

Functions of the on-off input interface

 Configuring the STATUS or COUNTER input

 Configuring the active status of the input (contact open or closed)

 Setting a timer for acknowledging a status change (anti-bounce function)

 Configuring the counter threshold

 Inhibiting the input

Functions of the output interface

The relay output interface can be programmed for:

 Configuring the type of relay output: monostable, bistable or flashing

 Configuring the type of NO/NC contact

 Controlling the Start/Stop output

 Controlling the Forcing Open/Closed output

 Configuring the time parameters of the output

XE MED V4B SCREEN MASTER STATION

Technical data sheet no. EN-604-0102A

www.castel.fr

Page 5 / 7

Functions of logical inputs (or flags)

Logic inputs allow two features in particular:

 create a logical state from which it will be possible to condition actions in relationships.

 create a counter that will be updated according to events and depending on the value of this counter to trigger

one or more actions.

Configuring relations

The Web server is where automatic controls, also called relations, are configured

There are two types of relations:

 Time: used to trigger actions at identified time slots. There are three levels of priority for a time relation (high,

medium and low).

 Logical:

↘ Logical condition: used to trigger actions at certain status conditions (active, inactive, etc.). A logical

relation can integrate several conditions by operators such as AND, OR, NOT, XOR. Likewise, a logical

relation can trigger several actions.

↘ Digital condition (Counting): used to perform actions by comparing the value of a counter with different

thresholds. It is also possible to add or subtract counter values and compare the result obtained.

Configuration of web server users (software users)

The Web server for the station can grant, modify or remove rights for users by specifying their login, password and

operating language.

Function for voice-transmission users of the station

In the user tab, you can create, edit or delete the voice-transmission users to whom you assign a profile. Then, a user

can log into the station using his/her username and password and activate his/her profile on the station.

Profile configuration

Station operating profiles can be created, modified or deleted. Each profile specifies a station priority, a configuration

of function buttons and access rights to the station.

The station can operate with a unique profile or with different profiles according to time slots.

SNMP administration management

The station features an SNMP agent (Simple Network Management Protocol) that can respond to SNMP queries and

send notifications (TRAPS) to an SNMP manager.

From web pages, it is possible to:

 Configure different communities (read/write)

 Configure system data (sysContact and sysLocation)

 Configure notifications (recipient, community, etc.)

 Download MIB Castel

It supports the SNMPv1 and SNMPv2c versions.

Self-test function

The station has several tests to validate its operation:

 HP/MIC self-test: can remotely test the right operation of the speaker and microphone. From the ‘advanced

parameters’ page, the levels of this test can be adapted according to the installation environment. This test can

be activated from the web server or by an SNMP command. The result of the test can be viewed from the web

server history and by an SNMP notification.

 Mechanical button self-test: the detection of a locked mechanical button (contact made for more than 20 s) is

signalled by an SNMP notification and an event is signalled in the web server history.

Backup and recovery of system parameters

A full backup or recovery of the station parameters can be made (configuration, profiles, relations, directory, etc.

The door entry station can be reset to factory settings by pressing the reset button for 10 seconds when the station is

started up.

Update by TFTP

Updating software with TFTP can be very useful when several stations must be updated.

The station is looking forward a TFTP server which provides the available software release. If the station is concerned

by this update, it downloads it and flashes it independently.

The updating software takes place most of the time when the software release on the server is newer than the one

installed on the station.

It is possible to force an updating process to a specific release of the TFTP server.

The TFTP server can request the stations to reset the current configuration, so the data partition is cleared.

It is possible to configure the station to detect a new release when the station is starting or cyclically.

XE MED V4B SCREEN MASTER STATION

Technical data sheet no. EN-604-0102A

www.castel.fr

Page 6 / 7

Backup on power outage

When a power outage occurs, the station can back up the following information:

 counter values

 history

 backed up events (these events are defined from CastelServer)

 The interface statuses

History function

The history displays station events. They are listed by showing the date and time of the relevant event, a description

and additional information.

Functions used to meet the accessibility law (depending on versions)

Rule: ‘Any signal related to the operation of an access device is audible and visual. ’

During the call, the entry station sends a configurable voice message and the call signal LED or a call visual on the

display switches on.

When the call is going through, the entry station sends a configurable voice message and the call signal LED or a call

visual on the entry station display switches on.

During the internal relay command at the station, the entry station sends a configurable voice message and the door

signal LED or a door visual on the display switches on.

Rule: ‘When there is an electric unlocking device, it enables any person with reduced mobility to reach the

door and start the opening manoeuvre before the door becomes locked again. ’

The entry station’s strike plate relay can be configured with a configurable hold time.

Rule: ‘In the absence of a direct view of these accesses by staff, the intercom devices feature a system

enabling staff to view the visitor. ’

The entry stations have a wide angle colour camera.

Rule: ‘When they are installed or renewed, the intercom devices have a magnetic induction loop. ’

Entry stations have an integrated magnetic loop.

XE MED V4B SCREEN MASTER STATION

Environmental protection:

Dispose of this product in compliance with the environmental protection regulations.

Technical data sheet no. EN-604-0102A

www.castel.fr

Page 7 / 7

CASTEL: ZAC de La Ronde – 10 route du Bois de La Casse – 49680 NEUILLE – France

Tel.: +33 (0)2.41.40.41.40 - Fax: +33 (0)2.41.40.41.49

Non-contractual photos and document. Concerned with achieving continuous improvement, CASTEL reserves the possibility of making any modification

considered to be necessary.

TECHNICAL CHARACTERISTICS

Compliance with European standards

 Safety according to EN 60950

 EMC emissions according to EN 55022 class B

 EMC immunity according to EN 55024

Mechanical characteristics

 Protection rating IP64 according to EN 60529.

 Polyester front panel.

 Flush mounting.

 Stainless steel case

 Dimensions:

↘ Front panel: H280 mm x W170 mm

↘ Embeddable base: H264mm x W116mm x

D47mm

General electric characteristics

 Protection against electric shocks, class 3

according to EN 60950

 Storage temperature: -20 ºC to +70°C.

 Operating temperature: 0 to +50°C

 Input voltage: 15VDC (15V to 30V)

 Consumption: 15V/150 mA in standby and

15V/200 mA during communication

Buttons

 Acquisition speed 5 Hz (200 ms)

Inputs

 2 protected and filtered digital inputs

 Acquisition speed 5 Hz (200 ms)

Outputs

 1 potential-free relay outputs

 Relay cutoff power 42.4 Vac/60 V dc/5 A/150 VA

 The maximum frequency is 5 Hz (minimum

switching time: 200 ms)

Display screen

 TFT colour touch screen 4.3”

Camera

 CMOS 1/5’’ 640*480

 Wide angle 110°

 Sensibility: 6V/Lux-Sec

 Low vision brightness: 5 Lux (minimum) to 80

Audio codecs

 G711 Ulaw/Alaw

 GSM

 G722

Video codec

 Video format CIF/QCIF

 H263

 H263-1998

 H264

DTMF

 RFC-2833

 SIP INFO

Ethernet 10/100/1000 Mbps network

 Fixed IP or DHCP

 PoE class0 conformity with standard IEEE

802.3af

 Security of Ethernet connections via protocol

802.1X

 SNMP V1 and V2c

Optimus XEMEDV4BSCREEN User manual

Brand: Optimus

Model: XEMEDV4BSCREEN

Category: Door intercom systems

Type: User manual

Download PDF

report

Optimus XEMEDV4BSCREEN User manual

Optimus XEMEDV4BSCREEN User manual

Related papers

Other documents