Contacta STS-K001L-B User guide

Brand: Contacta

Model: STS-K001L-B

Type: User guide

This manual is also suitable for

STS-K001L-G

Installation &

User Guide

January 2020

Window Intercom System

Bridge Bar Kit - STS-K001L

Contents

Product Overview

Components

Connections

Installation Instructions

Speaker & Microphone Kit Installation

  StaSideInstallation

Customer/Visitor Side Installation

Hearing Loop Installation

 AmplierSetup

Troubleshooting

Engineers Mode

Contactahasapolicyofcontinuousproductdevelopment,andthereforesmallspecication

changesmaynotbereectedinthismanual.Images,labels,packaging,accessoriesandproduct

coloursaresubjecttochangewithoutnotice.

Product Overview

Window intercom systems provide assistance for clear communication where

normal speech is impaired by use of glass, a security screen or other similar

barriers.

There is a hearing loop facility included, providing additional assistance for

hearingdevicewearers.

1. Installation and User Manual

2. Amplier

3. Hearing Loop Sticker

4. IEC Lead

5. PowerSupply

6. HearingLoopAerial

7. MountingBracket

Fixing Kit:

• Adhesive Clip x 10

• No.6x1/2”CountersunkScrewsx15

• P-Clips x 6

General Components

Speaker & Microphone Components

1. StaMicrophone

2. Bridge Bar

Connections

Hearing Loop

Power Supply

Bridge Bar

StaMicrophone

LED connection or alert tone (if required)

CondenceLEDtoconrmthesystemispowered

oranalerttonefortheattentionofsta

Stamicrophone

Customer/visitor microphone

CondenceLED(ifrequired)forstatusalerts

and fault detection

Hearing loop aerial

Line in connection for

external audio source

Staspeaker

Customer/visitor speaker

Power input

connection

Use power supply

through ground

supply only

Negative -

or screened cable

Positive +

Werecommendthatinstallationiscarriedoutbyaqualiedengineer,

adheringtorelevantstandards.

Checkthecontentsoftheboxtofamiliariseyourselfwiththecomponents.

Installation Instructions

A toolkit recommended to install the system will include:

Trim cables if necessary (excluding the power supply)

to the required length to connect to the back of the

amplier.Bareapproximately6mmofthecableendsto

connecttothe2pinplugs.

• Pliers

• Tape Measure

• Pencil or Marker Pen

• Torch

• Cable Ties

• Electrical Insulation Tape

• Trunking

• Screwdrivers(FlatorBlade2.5mm

and Phillips Head PH2)

• Battery or Mains Drill

• Drillbits: 2mm, 3mm, 5mm and 7mm

• Allen Key Set

• Cable Tacking Gun (10mm)

• Wire Cutters/Strippers

Recommended Tools

AhacksawmayberequiredforadjustmentstotheBridgeBarunit.

1. Placethestamicrophoneonthestasideofthecountertop,ensuring

thatitdoesnotcauseanobstructionandisasclosetostaaspossible.

2. Placetheamplierunderthestacounter,ensuringthatitwillnot

obstructstawhentheyaresitting.

3. Markthefourxingpointsfortheamplierunderthecounter.

4. Drillandxtheamplierinplaceusingthesuppliedscrews.

5. Useacablemanagementholetorunthestamicrophonecablebackto

theamplier.Ifthereisnotalreadyacablemanagementhole,drillina

suitablelocationneartherearofthesurface.

6. Installtheamplier’spowersupplyclosetoapowersocketoutletusing

thesuppliedmountingbracketandxingscrews.

Fixing points

StaSideInstallation

Speaker & Microphone Kit Installation

3. Ifthebridgebarneedstobenarrowed,calculatethewidthrequired

(minimum: 450mm) with the following steps:

a. Locatetheallengrubscrewsonthemountingbracketandloosen

themtoallowthebracketstoslidealongthetube.

b. Slidethebracketsinwardsuntilthedesiredwidthisobtained.Ensure

themicrophonestemisanequaldistancefrombothbrackets.

c. Ifnecessary,useahacksawtocutthebridgebartothecounter’s

requiredlength.Becarefultoavoidanydamagetowiring.

d. Ensurethebracketsareinthedesiredlocationandre-tightenthe

grubscrews.

4. Placethemountingbracketsadjacenttoeithersideofthepass-through.

Theyshouldbeapproximately2-3mmawayfromthescreen.

5. Markthefourxingpointsandtwocablemanagementholestobe

drilled.

1. Place the bridge bar on the counter top in a central location over the

pass-throughtray.

2. Disassemble the speaker pods by undoing the screws and removing the

housing.

Customer/Visitor Side Installation

Housing

xingpoints

Allen grub

screws

Allen grub

screws

6. Ensuretherewillbeaccesstoretrievethecables,thendrilltheholes.

7. Fixthespeakerpodstothecounterandfeedthewiringthroughthe

cablemanagementholes.

8. Retthehousingusingthescrewspreviouslyremoved.

9. Avoidlooseortrailingcables.Usetrunkingortopreventtriphazardsor

unitsbeingtuggedfromtheirposition.

10. Routeallthecablingneatlytotheamplierlocationonthestaside.

Cable

holes

Fixing points

Theaerialshouldbexedunderthedesk-toporcountercentrallyonthe

customeorvisitorside,onehalfmountedhorizontallyunderthecounterand

theotherhalfmountedvertically,facingthecustomer/visitor(asintherst

scenariobelow).

Position the aerial under the counter using either the provided P-clips

oranotherxingmethodofyourchoice.Seethediagrambelowfor

recommendedpositioning.

Aistheoptimumlayoutforacounterhearingloop.

B and C are acceptable only if A is not possible and the layout is aligned so

thatthemagneticeldwillbedirectedtowardsuser’sheadheights.

Ensureallhearingloopsignageisdisplayedclearly.

XX

Hearing Loop Installation

A B C

AmplierSetup

1. Connectallgreenplugstothebackoftheamplier,followingthe

locationsprintedabovethesockets(seepage4).

2. PowerontheamplierbypressingtheOn/Obutton.

3. Whenpoweredandinnormaloperationalmodetheamplierwilldisplay

VolumeInLED1andVolumeOutLED1assteadygreen.

4. Whentheamplierisswitchedo,allaudioismutedandnoneofthe

LEDsareilluminated.Pressinganybuttonwillturntheamplieronagain.

5. AdjustVolumeInandVolumeOuttoacomfortablelevel.

6. Press and hold the Volume In (+) or (-) buttons to increase or decrease the

level.ThecorrespondingLEDbarwillshowthevolumesetting.

6. Ensure the mouse microphones are placed as close to their intended

usersaspossible.

7. Checktheamplierisfullyfunctionalbyensuringthered‘fault’lightis

NOTshowingonthefront.

8. The Amplifier is now set up.

OurWindowIntercomSystemampliersarepre-settovolumelevels

suitablefornearlyallusers.ShouldyouneedtoadjusttheMaximum

Volume,DuckingorHearingLooplevelsoutsideofthepre-setamplier

parameters,useEngineer’sMode(seepage13).

Overview of Front Panel Buttons

Volume In (Customer/Visitor to Staff)

Increase and decrease

Volume Out (Staff to Customer/Visitor)

Increase and decrease

Settings

On/O

Setup

Factory Default Settings

Fault Diagnosis LEDs

• Volume In LED 8 will stay red if there is a

faultwiththestamicrophone.

• Volume Out LED 8 will stay red if there is a

faultwiththecustomer/visitormicrophone.

• VolumeInLED8willashredifthereisa

faultwiththeloop(e.g.abrokenaerial).

Toreturntheampliertothefactorydefaultsettings:

1. Unplugthepowersupplyandthenreconnectit.

2. TheLEDindicatorswillshowalightpatterninthe“VolIn”column.This

indicatesthermwarerevision.Thiswillbefollowedbyagreenlight

atthebottomofeachcolumn.     

3. Within20seconds,presstheOn/ObuttonandVolumeIn(-)button

together,thenreleasethem.     

4. The“VolIn”columnwillagainindicatethermwarerevision.Thisindi-

catesthatthesettingshavebeenrestored.

Symptom Possible Fault Action

There is no

power

detected

through the

amplifier (and

there is power

at the socket).

1) Power jack not plugged in or

faulty.

2)Plugfusehasblown.

3) Faultypowersupplyunit.

4)Faultyamplier.

1)Checkpowerjackisrmlyplugged

in.

2)Replacefuse.Ifitblowsagain,

replacethepowersupplyunit.

3)Replacethepowersupplyunit.

4)Replaceamplier.

The red LED is

illuminated on

front panel.

1) Constant red LED:

Staorcustomer/visitormicrophone

fault.

2) Red LED comes on after speech:

Inductionloopfault.

1) Ensure microphone is wired

correctlyandrmlypluggedin. Try

alternative microphone to ensure

portisworking.

2) Ensure induction loop connector is

wiredcorrectlyandrmlypluggedin.

I can’t hear

audio through

the induction

loop.

1) Induction loop or microphone is

disconnected.

2)Looptesterhasafault.

1 ) Check instructions for correct

connections and, if possible, check

the hearing device with a known

workinghearingloop.

2) Ensure loop tester has a new set

ofbatteries.

I can hear

interference

through

speakers

(buzzing /

whistling /

hissing).

1) Unscreened or poorly earthed

third party equipment is being used

incloseproximity.

2)Internalvolumegainsettohigh.

3) Incorrect power supply being

used.

1)Switchoanythirdparty

equipment to identify the source of

interference.

2)Accesstheamplierengineers

modetoadjusttheinternalsettings.

3) Ensure that our grounded power

supplyunitisconnected.

Amplifier goes

into feedback.

1)Internalvolumegainsettohigh.

2) Microphone positioned too close

tospeaker.

1)Accesstheamplierengineers

modetoadjusttheinternalsettings.

2) Move the microphone to a

locationfurtherfromthespeaker.

Unit does not

go into power

saving mode.

1)Ambientnoiseinareaistoohigh. 1)Switchoanyairconsystems,

desktop fans and/or computers to

reduceambientnoise.

Troubleshooting

If no action is successful please seek assistance from

yourdistributororaContactainstaller.

Engineer’sMode

BeforeenteringEngineer’sMode,cyclethepower.Todothiseither:

• Switchthepoweroatthemainssocketandbackonagain

• Removethepowerconnectorandre-insertit

ToenterEngineer’sMode,simultaneouslypressandreleasethefollowing

buttons within 20 seconds of cycling the power:

• Settings button

• Volume In increase button

• Volume Out increase button

Number1LEDontheVolumeInwillashgreentoindicatethatyouarein

Engineer’sMode.

Theon/oandsettingsbuttonsinEngineer’sModeoperateasfollows:

SaveandexitEngineer’sMode

Move to the next setup area

TheamplierwillautomaticallyexitEngineer’sModeifnobuttonsare

pressedfor2minutes.

Thereare3editablesetupareasinEngineer’sMode.Youwillalwaysenter

setuparea1rst.ThegreenVolumeInLEDbarwillashtoindicatewhich

setupareayouarein.

Setup Area 1:

Maximum Volume Adjustment (LED 1 flashes)

Setup Area 1 allows you to adjust the Volume In and Volume Out levels to

furtheroptimisethesystemfortheenvironmentinwhichitisinstalled.

Engineers Mode allows you to adjust the Volume In and Out levels, Ducking

levels and Hearing Loop levels to better suit your environment and achieve

thebestpossibleperformance.

Increase maximum

stavolumelevel

Decrease maximum

stavolumelevel

Increase maximum

customer volume level

Decrease maximum

customer volume level

1. Ensurethecustomer/visitorandstavolumesareturneddown.

2. Adjuststa(VolumeIn)volumetoacomfortablelevel.Pressandhold

theVolumeIn(+)or(-)buttonstoincreaseordecreasethelevel.The

correspondingLEDbarwillshowthevolumesetting.

3. Raisecustomer/visitor(VolumeOut)volumeuntilfeedbackisheard.Press

and hold the Volume Out (+) or (-) buttons to increase or decrease the

level.ThecorrespondingLEDbarwillshowthevolumesetting.

4. Lowercustomer/visitor(VolumeOut)volumeuntilfeedbackiseliminated.

Setup Area 2:

Ducking Adjustment (LED 2 flashes)

SetupArea2allowsyoutoadjusttheDuckinglevelortoturniton/o.

The ducking function is provided to reduce feedback on a window intercom

system.Feedbackoccurswhentheoverallsettingofbothvolumecontrols

istoohigh.Theduckingsystemworksbydetectingwhichmicrophoneinthe

conversationisbeingused,andtemporarilyreducingthevolumesetting.

Increase

ducking level

Decrease

ducking level

Ducking on

Duckingo

Increase drive

Decrease drive

The drive levels should be adjusted so the red LED 8 is illuminated only when

Setup Area 3:

Hearing Loop Drive Adjustment (LED 3 flashes)

SetupArea3allowsyoutoadjusttheHearingLoopDriveortoturniton/o.

Hearing loops improve communication by enabling hearing device users to

hearsoundsourcesdirectly,cuttingoutbackgroundnoise.

Hearing Loop Drive on

HearingLoopDriveo

therearepeaksinthespeechvolume.

Iftheamplierdoesnothavealoopattached,turntheHearingLoopDriveo

asindicatedinthediagramabove.

www.contacta.co.uk

[email protected].uk

+44 (0) 1732 223900

Technical Support - Ext 5

Further information is available on our website and our YouTube channel.

WindowIntercomSTS-A31HAmplier

Setup Video

Window Intercom Unboxing &

Positioning Guide Video

Contacta STS-K001L-B User guide

Brand: Contacta

Model: STS-K001L-B

Type: User guide

This manual is also suitable for

STS-K001L-G

Download PDF

report

Contacta STS-K001L-B User guide

This manual is also suitable for

Contacta STS-K001L-B User guide

Related papers

Other documents